• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Recent content by JGordon

  1. J

    GS1100 Head Building

    Thanks guys....I'll take a look at these places. JGordon
  2. J

    GS1100 Head Building

    Anyone know of a reputable place to get a head built? Looking for OS valves with a nice port job. 1260 motor w/ 345 lift cams. Jgordon
  3. J

    77 GS 750 with Wiseco 844 kit

    This is what happens when a motor sits for a while without being ran or turned over. Depending on how deep the pits are is whether it will clean up. I would probably try and get a used set in good shape.
  4. J

    gs1100esd cyl stud install

    You can take a look at your cylinder head and see from where the studs come through the heights and go from there. I've put a few set's in but always looked at the head to make sure they are in the right spot.
  5. J

    82 GS1100E Project/Cleanup

    Tech, Where did ya get the new harness?
  6. J

    82 GS1100E Project/Cleanup

    Its looking good. I did one like this but am only running one carb to make is easier to keep synced up and a little air compressor to give it a couple of more HP (-:. You are doing and excellent job!!!
  7. J

    Nasty Oil and Scored Up Pistons

    Yep. Pretty bad. I have a bigger setup I'm puttin' in it so not a big deal.
  8. J

    Nasty Oil and Scored Up Pistons

    I was taking off the 1150 head and putting on a better ported 1100 head and noticed some nasty oil. I pulled the cylinders and saw that the pistons were scored so decided to take it on down and get the cases bored for a little bit bigger piston kit. When I pulled the clutch hub I found the...
  9. J

    1230

    Finishing up my turbo project. Finished up the CL450 project. Building a 47' Knucklehead. Putting a 1260 in my street bike. You know......just tinkering (-:
  10. J

    1230

    Looking good there Chef.
See more
Back
Top