My Homemade Manometer (pics!)

[C.V.]

So after much internet research, and less than 20 bucks, here it is, after growing another 3 feet...



It is 4 half inch OD clear tubes, originally 4 feet, ultimately 7 feet, terminating into a common airtight reservoir, filled with ATF. I stepped the vacuum end down in size twice, once down to smaller vinyl tubing (about 5 feet worth, the "whips"), then down to the size of the vacuum line using a new female bullet connector to splice the 2 together, this also served as a good vacuum restictor! The bench sync was so far off (and i really thought it was very close!) that cyl one was drawing so much more vacuum, that i needed to extend the the tubes to compensate for the error. It didn't matter once I got them close, as you can see in the next 3 pics. These are three different adjustments (after getting them close), with the last one where i left it.

[tkent02]

Congrats, how does it run now?

[C.V.]

video

here is a quick video of it functioning...don't pay much attention to what i am saying, I thought i was finished, but I wasn't..The thing was very sensitive, a slight turn of the adjuster would make a big difference. You can see cyl one shoot up with just a litlle turn. Almost no intake pulse.

[C.V.]

Congrats, how does it run now?

Much smoother through out the whole power range now, very noticeable difference. I wasn't really unhappy with the bench, it ran OK, but it was way off! Never assume that it is good enough with getting a vacuum sync on it!


Hey, special thanks to Bob (Baatfam) for donating the vacuum barbs!

[Griffin]

Good job, I like it. It kinda reminds me of the old county fair game where you hit the base pad with a sledgehammer and try to ring the bell at the top.


Yeah, I've learned myself that bench-syncing is essentially worthless. Every time I've rebuilt carbs, bench-synced them, then mounted and synced them properly, at least one, sometimes two cylinders have been WAY off of the two that were pretty close.

Home made manometer, vacuum gauges, mercury sticks, Morgan carb tune, it doesn't matter. You just need some objective method to compare intake vacuum levels, or your bike will never truly run right.

[Baatfam]

Good job, Victor...I'm glad to see it all worked out...

[Bufallobiff]

What type of fitting do you need to access the vacuum in the inlet rubbers and where can you get them? I got a Twinmax on Ebay but it had no adapters.

[themess]

I second that question. The lowest price I've seen is about $8 each. That's a big step towards a Morgan Carbtune.

[Nessism]

I've read about people drilling down through a socket head screw and epoxying a piece of brass tubing in the socket so a piece of tubing can be attached. Not sure what thread and pitch but the info is in the archives if you care to search.

BTW, great job CV. I love do-it-yourself projects.

[Baatfam]

What type of fitting do you need to access the vacuum in the inlet rubbers and where can you get them? I got a Twinmax on Ebay but it had no adapters.

I second that question. The lowest price I've seen is about $8 each. That's a big step towards a Morgan Carbtune.

Z1 sells 5mm adapters for just over $9 a set...

Vacuum Carb Sync Adapter Kit 5mm

[Steve]

Nice job.

Depending on the amount of fluid in your reservoir, you could probably lower the level to the bottom of the tubes, as long as the tubes are still immersed in fluid.
That would reduce your overall height of the manometer that much more.

Now, after it's all done (and, you say, worth it), just how much time to you figure you have invested in this project, including all the research, material acquisition and assembly?

How much do you value your time?

How do you plan to store your gauge until the next time you use it?

Do you think that overall, it was worth all the time (and its value) rather than $90 for a ready-made item (that is only about 18" long and won't leak)?

Please, expiring minds want to know.

.

[Nessism]

Nice job.

Depending on the amount of fluid in your reservoir, you could probably lower the level to the bottom of the tubes, as long as the tubes are still immersed in fluid.
That would reduce your overall height of the manometer that much more.

Now, after it's all done (and, you say, worth it), just how much time to you figure you have invested in this project, including all the research, material acquisition and assembly?

How much do you value your time?

How do you plan to store your gauge until the next time you use it?

Do you think that overall, it was worth all the time (and its value) rather than $90 for a ready-made item (that is only about 18" long and won't leak)?

Please, expiring minds want to know.

.

Geeze Steve, some people don't want to spend $90 on something they can make themselves for $10, regardless of how much time they spend. And even if it costs more than $10, the satisfaction and knowledge people learn from DYI projects can not be calculated. This is the GSR, not some late model bike forum where people take their bikes in for oil changes.

[Dave8338]

Geeze Steve, some people don't want to spend $90 on something they can make themselves for $10, regardless of how much time they spend. And even if it costs more than $10, the satisfaction and knowledge people learn from DYI projects can not be calculated. This is the GSR, not some late model bike forum where people take their bikes in for oil changes.

...Either way, the end result is what matters. I've made things and had twice as much in them as I could have purchased them for, but it bought me precious time in the shop and at the end of the day, one can always say: "I did it my way".

Nice job on the sync tool. A bench sync gets things close enough to get them running. The final set still needs to be done with the trans fluid...

[Steve]

Yeah, I've learned myself that bench-syncing is essentially worthless. Every time I've rebuilt carbs, bench-synced them, then mounted and synced them properly, at least one, sometimes two cylinders have been WAY off of the two that were pretty close.

Either you need more practice or I have been incredibly lucky. I have gotten them close, but you are right that it is not a substitute for a good vacuum sync.

I got a Twinmax on Ebay but it had no adapters.

Unless you have a twin-cylinder bike, the Twinmax is only marginally better than a single gauge and manifold. As C.V. mentioned, it's amazing to see how one small tweak of the screw affects them all.

.

[Griffin]

Nice job.

Depending on the amount of fluid in your reservoir, you could probably lower the level to the bottom of the tubes, as long as the tubes are still immersed in fluid.
That would reduce your overall height of the manometer that much more.

Now, after it's all done (and, you say, worth it), just how much time to you figure you have invested in this project, including all the research, material acquisition and assembly?

How much do you value your time?

How do you plan to store your gauge until the next time you use it?

Do you think that overall, it was worth all the time (and its value) rather than $90 for a ready-made item (that is only about 18" long and won't leak)?

Please, expiring minds want to know.

.

From personal experience, I know that when you're between jobs, your time can be worth a lot less than than at other times, particularly when something costs the same as a week's worth of groceries.

Speaking of which, hey Victor, how's the job hunt going? Any more leads?