S
shibby_cbs
Guest
it is now leaking and couldnt find it in the parts fiches...anyone know where i can get one?
-
Required reading for all forum users!!!
Welcome!
Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.A note to new registrants...
All new forum registrations must be activated via email before you have full access to the forum.A Special Note about Email accounts!
DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.A note to old forum members...
I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.
Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...
-
Returning Visitors
If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.
If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.
Check out parts number 8 and 9 here:
6CABLE,CLUTCH
58200-34X00 (replaces 58200-34200) 1$20.70 7
09125-05034 1$0.65 8.PIN
09209-10019 1$2.06 9.DUST SEAL
09287-07003 (replaces 09287-07004) 1$2.27
These are from the dealer fiche here in Colorado Springs
58200-34X00 (replaces 58200-34200) 1$20.70 7
09125-05034 1$0.65 8.PIN
09209-10019 1$2.06 9.DUST SEAL
09287-07003 (replaces 09287-07004) 1$2.27
These are from the dealer fiche here in Colorado Springs
Or if it's inside the clutch area than parts number 26 and 27
26OIL SEAL (12X22X9)
09285-12006 (replaces 09285-12002) 1$4.41 27BEARING (15X22X12)
09263-15012 1$8.87
26OIL SEAL (12X22X9)
09285-12006 (replaces 09285-12002) 1$4.41 27BEARING (15X22X12)
09263-15012 1$8.87
S
shibby_cbs
Guest
26 and 27 it is...thanks
D
DPage
Guest
How remove seal? 09285-12006
How remove seal? 09285-12006
Did a search and found this thread. I have the clutch cover off my '82 850G, and am trying to replace the clutch arm oil seal (#26 on the clutch cover fiche below), part # 09285-12006. This is a hard rubber seal with a small little coil spring around the base, kind of like a tach drive seal only a little bigger. I've tried digging it out with a small knife, cutting it with an Xacto blade, and finally attached the clutch arm itself and tried to beat the arm with a rubber hammer - no luck. Any ideas on how to get this pesky seal out?
How remove seal? 09285-12006
Did a search and found this thread. I have the clutch cover off my '82 850G, and am trying to replace the clutch arm oil seal (#26 on the clutch cover fiche below), part # 09285-12006. This is a hard rubber seal with a small little coil spring around the base, kind of like a tach drive seal only a little bigger. I've tried digging it out with a small knife, cutting it with an Xacto blade, and finally attached the clutch arm itself and tried to beat the arm with a rubber hammer - no luck. Any ideas on how to get this pesky seal out?
D
DPage
Guest
Well, I made a little progress on this. Soaked it in paint thinner overnight, and chipped some of it out by working carefully with an Xacto knife. There is an inner and outer race this seal fits into, and I was able to remove all the material from the thicker, inner race. It got better, more pliable the deeper I went, probably from less oxidation/exposure. Still, digging around with an Xacto for a couple hours and going through about 4 blades was no fun.
The outer race is much thinner so it will be much more difficult to get out with an Xacto knife. Would heat from a propane torch help, perhaps?
The outer race is much thinner so it will be much more difficult to get out with an Xacto knife. Would heat from a propane torch help, perhaps?
D
DPage
Guest
OK, I figured it out how to remove the seal. This seal is a metal band surrounded by hard rubber. You could probably just hit the outside with an awl and pry it out, but of course I had to make it harder than that. I was afraid of damaging the clutch cover, so I wasted about a dozen Xacto knife blades trying to cut it out. I knew I was hitting metal in the middle, but I thought it was the clutch cover, not the seal itself. In desperation, I heated the whole seal with a propane torch, and softened the rubber enough to pry the whole thing out. If you just use an awl, you can probably do it with the cover on the bike with no heat. If you want to add a little propane action or maybe a hairdryer, take the cover off first so you don't become a crispy critter.
There's another way...
Remove the cover, and use a long, thin punch at a slight angle to knock the clutch shaft out from the bottom. It'll push the bearing and seal out the top.
You do have to come up with a way to secure the clutch cover without damage, which can be the most difficult part of the project.
Remove the cover, and use a long, thin punch at a slight angle to knock the clutch shaft out from the bottom. It'll push the bearing and seal out the top.
You do have to come up with a way to secure the clutch cover without damage, which can be the most difficult part of the project.
D
DPage
Guest
Brian, you bum! I've been worrying about this for a week, and you throw in your expertise now! Actually, I tried to hit the back end of the shaft with a long punch to force it all out, but almost destroyed the edge of my workbench and the punch wasn't long enough. Plus, I didn't know if pounding on that hard metal would fix it or destroy it. I like my way better. By the way, chemicals don't work either - acetone, my other ace in the hole, doesn't touch hard rubber.
Well, there's more than one way to skin a cat... 
Your way risks heat damage to the finish, and damage to the seal bore from the pics and tools used. All in all, it's probably the best method for many.
My way risks damaging or cracking the cover if you don't secure the cover properly, or clamp it too hard. You have to have a good bit of experience working with engine parts in order to avoid this. It's also hard to find a punch long enough to work well. I don't think the bearing gets damaged in the process, but that's also possible.
Neither is ideal, so until we discover the One True Way to remove these things, we might as well present all the options when the topic comes up.
For those playing along at home, the basic problem is that the seal is very deep compared to most -- you can't just pry it out of there because the seal can't tilt.
Your way risks heat damage to the finish, and damage to the seal bore from the pics and tools used. All in all, it's probably the best method for many.
My way risks damaging or cracking the cover if you don't secure the cover properly, or clamp it too hard. You have to have a good bit of experience working with engine parts in order to avoid this. It's also hard to find a punch long enough to work well. I don't think the bearing gets damaged in the process, but that's also possible.
Neither is ideal, so until we discover the One True Way to remove these things, we might as well present all the options when the topic comes up.
For those playing along at home, the basic problem is that the seal is very deep compared to most -- you can't just pry it out of there because the seal can't tilt.
K
kpotter16
Guest
i pulled mine out by getting a small L shaped pick behind it and just pulling it out, just incase you havent got it out.
Up and down play in the shaft is normal and necessary.
Good luck with the picks, but it takes a good bit of force to move that seal
I installed my seal a bit tight I think. Time will tell. Here is a link to a thread I did when I replaced mine. http://www.thegsresources.com/_forum/showthread.php?t=157735&highlight=shaft+seal
cg
cg
