• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Front brake switch

  • Thread starter Thread starter mpogue
  • Start date Start date
M

mpogue

Guest
I was told that the brake light on my GS1150EFF was not coming on very often during braking. After checking it out I found that if I braked lightly, the brake light wouldn't come on, but if I grabbed a good handfull of the lever it did.
All I can see is two screws holding the switch on under the master cylinder. Nothing I have tells me the makeup of the switch. While I had the bike apart on the weekend I forgot to check this out.
Is there away to adjust the switch to pickup a smaller movement of the lever? Is the switch a pressure switch? If I remove it, will I start loosing brake fluid? (don't want that stuff all over the fairing :x ) Or is it some kind of magnetic non-contact switch? It seems too small for a micro switch.
Any help would be appreciated.

Thanks :)
 
The switch you are dealing with is a contact switch. Chances are it is quite corroded and that is why you aren't making the contact.

You can take it appart without loosing any fluid, however be careful, as there is a spring in there that really likes to find it's way into unknown places once left loose.

Alternatively, check out this thread:

http://www.thegsresources.com/_forum/viewtopic.php?t=21717

it is a review on a Hydraulic switch available from DennisKirk and has gotten a good review on this site.

Hope that helps you out.

Amos
 
There is some adjustment on the switch. Under the cover is a small circuit board that can be moved. Also clean all the contacts if you take it apart. Be careful about the parts that will fall out of the brake lever. There is a T-shaped piece of plastic that a spring slides into and a U-shaped contact. Try just sliding the circuit board first by backing off on the screws and moving the whole housing.
 
:oops: ](*,)

You know, I remember looking at that a while back. It just didn't register. I never searched thinking it was an odd problem.

Thanks Amos and Billy :)

I'll check the switch out first. If any problems, I'll be looking for the pressure switch.
 
Not a problem, In the future, when I can afford it, I plan on purchase these myself.

Amos
 
Try loosening the screws just a bit and tapping the switch back and forth a bit to change its position slightly. With a few tries, you can usually sort of recalibrate where it comes on.

It's the most wretched, touchy, cruddy, overly sensitive, subject-to-failure mechanism I've ever seen, but there's no point in taking it apart if you don't have to.

Failing that, you could replace it with a proper hydraulic switch as suggested earlier. You could also get a new replacement switch from Cycle Recycle:
http://www.crc2onlinecatalog.com/brake_switch.htm
 
bwringer said:
It's the most wretched, touchy, cruddy, overly sensitive, subject-to-failure mechanism I've ever seen, but there's no point in taking it apart if you don't have to.
Click to expand...

The funny thing about it is the clutch switch is basically the same, gets used more, and seldom do you ever here of trouble with it.
 
Billy Ricks said:
bwringer said:
It's the most wretched, touchy, cruddy, overly sensitive, subject-to-failure mechanism I've ever seen, but there's no point in taking it apart if you don't have to.
Click to expand...

The funny thing about it is the clutch switch is basically the same, gets used more, and seldom do you ever here of trouble with it.
Click to expand...

Also the switches will interchange, if looking in the used market.
 
When adjusting my brake switch for the first time, I discovered the cover had a crack in it. I cleaned up the internals, got it activating correctly, and found myself doing the same service only a month later! I took the cover off, and found everything coated in dirt and crud again, after only a month. Came to the conclusion the crack in the cover was allowing the weather into the switch. I mixed up some quick set expoxy, and lightly filled/coated the crack, and reinstalled the cover. That was a year and a half ago, with no further trouble (so far!).
I *will* be buying one of the hydraulic replacements the next time. 8)
Scott
 
What a piece of engineering crap... 8O ....

I can't believe how they made the switch. All you're doing is dragging a piece of copper over two exposed wires.

Taking it apart really wasn't that bad. It was the not knowing how it works before I look it apart that scares me. You know, when you pull it apart and something flys out only to find out you never saw how it was together before it happened. 8O

Well, it was gummed up with a bit of dirt, and some corrosion, but it was't too bad. A cleaning with a metal brush to polish the copper and some electrical lube, and it works better. The adjustment is not much to write home about. :|

I now see why changing to the hydraulic pressure switch is the best way to go next time.

Thanks for all the help everyone :)
 
You must log in or register to reply here.
Back
Top