Announcement

Collapse
No announcement yet.

1981 Kawasaki GPz550: Restoration

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Weekend Update 6/24/18:

    I don't give up, I just don't have enough time. The spark plug pics in #463 were the Accel (NDs) which I ran with the 32.5 pilots. I used the same plugs for a carb synchronization so they got very discolored. I decided to start from Step 1 and installed a new set of NGK D8EA's and see how the GPz ran. Cleaner but the carburation still surged. Back at the garage, I turned all the air screws to 1 turn out.

    Took another test ride and what a transformation. First the GPz started immediately and idled on its own. Second it pulls cleanly and hard out of corners even under 3K rpm. The engine idle was set way way too high with the air screws at the right setting. It was idling at 4K rpm which tells me how far off the previous setting were. I now had some confidence to ride the GPz on the main road, after twenty miles the spark plugs looks like this so I am feeling pretty good the Mikuni Smoothbores are viable. Even better I don't have any engine oil leaks.





    I would like to thank Roger (Burque73) for helping me find a KZ550 Vance & Hines 4 into 1. Roger heard of a guy named Greg through one of his friends who has several 1981 GPz550 parts bike. I finally contacted Greg and purchased this rusty but undented Vance & Hines for a great price. Light sand blast, followed by VHT will transform it back to life . Hope it gives me center stand access again.

    The only bad thing during the ride was my MotoBat battery nearly died so now I have charging T/S. Strange I know I saw good voltage with the DMM across the battery terminals.

    Last edited by srsupertrap; 06-24-2018, 03:19 PM.
    Steve

    1979 GS1000E (45 Yrs), 1981 GPz550 (11 Yrs)

    Comment


      Step at a time, eh Steve? This bike is so cool, it deserves the love and attention you've devoted to it. That pipe looks very similar to a Kerker. Should look and sound great when installed.
      1979 GS1000S,

      1982 Honda CX500 Turbo, 1982 Honda MB5 w/CR80 motor, 1977 Honda "nekid" Goldwing, 1976 Honda CB550F cafe', 1972 Honda XL250 cafe'

      Comment


        Originally posted by nvr2old View Post
        Step at a time, eh Steve? This bike is so cool, it deserves the love and attention you've devoted to it. That pipe looks very similar to a Kerker. Should look and sound great when installed.
        Larry, You're right, one thing at a time and if you don't do it right the bike lets you know. During the week I went over the R&R and stator wiring. The charging system is exactly like a later GS model. When I went over the wiring harness originally, I knew one of the three stator wires had overheated and was stiff. I cleaned the connection with a drill/wire brush and moved on. Although the resistance was low on all three stator wires from this picture to the stator electrical connections, I decided to replace the connector on the left.



        I cannibalized the exact same wire and stator connector from the KZ550 wiring harness. Then decided to use KZ550 six wire connector too. The R&R wiring was all good but I noticed the ground wire from the R&R disappeared into the main wiring harness. If I have learned anything from reading Posplayr R&R threads over the years its that adding a ground leg to the R&R (-) and running the additional ground to the same point where the Negative battery cable is grounded is beneficial for charging health. Not sure if that is power grounding but I performed that task too. Here is how the repaired stator connector looks. I buttoned up everything and I will test the charging circuit Saturday morning.

        Steve

        1979 GS1000E (45 Yrs), 1981 GPz550 (11 Yrs)

        Comment


          7/16 Update: The GPz550 is carbureting very well but the charging system output across the battery is weak making idling aproblem. Before going for a ride last night, I checked the battery charging voltage with a DMM. I was reading 13.5 volts across the battery @ 4k RPM but it took a while to creep up to 13.5 Volts. When I returned from a five-mile ride I took more DMM measurements across the battery terminals. At 2k RPM, I am reading 12.8 Volts across the battery. At 4k RPM, I am reading 13.1 Volts across the battery with a Digital Multi Meter so while riding the battery is being drained. Per Factory Manual its exactly like a Suzuki GS, at 4k RPM it should be around 14V so obviously either the Stator or R&R is marginal. The GPz550 has a Shindgen R&R six wire with the sense wire connected to "+" terminal. I did run an additional ground from the R&R ground directly to the battery ground on the engine case.

          Looks like I have to check the R&R diodes and stator output but any other suggestions?
          Steve

          1979 GS1000E (45 Yrs), 1981 GPz550 (11 Yrs)

          Comment


            Get a SH775 and slam that in straight away Steve. You can find good used units from ebay for $40. Eliminates one headache.
            Ed

            To measure is to know.

            Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

            Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

            Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

            KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

            Comment


              Disconnected the 6p connector and checked the GPz550 R/R Wednesday night The diodes checked out with the DMM per the Factory Manual T/S section reading(1.5M to 1.8 M Ohms) in one direction and open in the other. The SH775 may be an upgrade I look at in the future after reviewing threads on the topic and learning about connectors.

              I will check the stator output between the three leads tonight, difficult revving the engine to 5k and juggling the DMM leads.



              Last edited by srsupertrap; 07-19-2018, 09:44 AM.
              Steve

              1979 GS1000E (45 Yrs), 1981 GPz550 (11 Yrs)

              Comment


                The factory R/R is a robust Shindengen unit. Most likely your stator is weak. I had the same problem with my KZ. On my bike the no-load AC voltage was high but the charge voltage never got above 13.7 V or so. I spent a lot of time chasing my tail because I assumed because the stator was showing high AC voltage that it was good. False assumption. A high no-load voltage doesn't mean your stator is strong, but a low no-load voltage does mean the stator is bad.

                Regarding an SH775 harness, Triumph sells a very nice pigtail that can be easily modified for use on your bike. P/N T2500676
                Ed

                To measure is to know.

                Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

                Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

                Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

                KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

                Comment


                  Spent more time T/S the GPz charging system this last weekend and found some interesting findings, eliminated several issues but didn’t resolve the low charging problem. First, I checked the resistance between the three stator leads and ground. The resistance value should be open; I verified all three leads read “OL”.

                  Then I performed a meter test on the Shindengen SH230 R&R per Electrex World T/S chart. First I disconnected the R&R and selected the DMM diode setting. I tested the R&R by connecting the positive lead to the R&R ground wire and used the black lead measure the three R&R stator wires. Per the T/S chart the voltage reading should be between .35 to .75V. Then connected the black lead to the Red R&R wire and used the positive lead to test the three R&R stator wires. All six R&R measurements were between those values (.491 - .502V).

                  Next I checked the stator resistance. The Kawasaki service manual states the resistance between the 3 yellow stator leads should be .32 to .48 Ω. I cleaned all the stator terminals to shiny metal before taking measurements and measured .6 to .7 Ω on every lead combination.
                  ]

                  I then checked the meter lead resistance and that measured .1 Ω. If I subtract .1 from .6 I get .5 Ω close to factory spec but still higher.

                  Next stator output, the table from the Kawi Service Manual shows I should have 75VAC @ 4K rpm. I disconnected the stator leads, ran the bike @ 4K rpm and measured VAC between the three stator leads. My test results were 52-56 VAC much lower than the Factory Manual by some 20%.

                  ]

                  Feeling hopefully I pulled a known good stator from the 82 GPz550 rolling chassis I bought in Colorado Springs for $150. Cleaned up the leads, added new rubber connectors, carefully installed the stator it and got the same exact test results of 53-56VAC.


                  Since the VAC output and resistance between the stator leads was identical for two OEM stators shown I can only conclude the generator magnets on the flywheel I have installed must be weak. What else could account for the same result when measuring VAC output between the three leads pictured above. I ordered a good looking KZ550 generator from Ebay should be here 7/31.
                  Steve

                  1979 GS1000E (45 Yrs), 1981 GPz550 (11 Yrs)

                  Comment


                    Steve,
                    You are experiencing a very similar situation to what I went through with my KZ. I tried two different used stators, three different R/R's, and still couldn't get the charging voltage up. Finally bought a new Rick's stator and SH775 and bang, 14.5 VDC @ 5000 rpm.
                    Ed

                    To measure is to know.

                    Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

                    Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

                    Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

                    KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

                    Comment


                      Ed,
                      Thanks for sharing your KZ charging issues and your experiences with resolving it. Didn't realize you had all those problems. Since I have a used EBay generator flywheel enroute I will give that a try. I am also going to clean up the stator pole corrosion seen below on the original stator before testing. Not sure if corrosion would reduce VAC output or not but electricity likes clean contact surfaces. Curious did you check the Rick's for VAC output?



                      If the flywheel arrives this weekend and if the VAC & charging voltage are still below spec. I will just order the Rick's that same day. The KZ550 & KZ750 might share the same stator P/N too.
                      Steve

                      1979 GS1000E (45 Yrs), 1981 GPz550 (11 Yrs)

                      Comment


                        I am betting that bit of rust is doing nothing negative.
                        1983 GS 550 LD
                        2009 BMW K1300s

                        Comment


                          Originally posted by Nessism View Post
                          Steve,
                          You are experiencing a very similar situation to what I went through with my KZ. I tried two different used stators, three different R/R's, and still couldn't get the charging voltage up. Finally bought a new Rick's stator and SH775 and bang, 14.5 VDC @ 5000 rpm.
                          Looks like Ed was right again. I installed the shiny used EBay Flywheel this last weekend. Tested the stator ouput and the VAC output dropped from 53 to 50 VAC so I ordered a Rick's stator which should be here Friday. I will install the original flywheel while I am at. Fingers crossed for charging health
                          Steve

                          1979 GS1000E (45 Yrs), 1981 GPz550 (11 Yrs)

                          Comment


                            Steve,
                            Your bike is three phase but the 1980 KZ550 used a one phase charging system. Can't remember what year your parts bike was but you need to use a three phase R/R. According to partzilla the flywheel rotor is the same for all years so apparently there are no magnet differences.
                            Last edited by Nessism; 08-02-2018, 10:38 AM.
                            Ed

                            To measure is to know.

                            Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

                            Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

                            Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

                            KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

                            Comment


                              I thought this would be a quick swap: Discard the EBay flywheel which measured lower voltage output and reinstall the KZ550 parts bike flywheel which went smoothly. I bought an open box Rick's KZ550 stator shown installed but it didn't slip right in. The rubber grommet width was 1.25mm wider than the OEM stator grommet so it wouldn't fit. Broke out the dremmel and milled the rubber down till I could force it in. Before I could do that the rubber grommet was not positioned correctly along the three stator wires. Sprayed the stator wires with penetrating oil and then inch the rubber grommet into the correct position. I also had to trim the wire conduit cover too. I suspect this stator's wires were not terminated in the correct position.

                              [IMG][/IMG]

                              Ops check in the garage today. Initially I saw battery voltage then after running at 2500 rpm it jumped into the 14.5VDC and then climbed into the 15.2VDC values. I guess the Shindegen regulator isn't. The picture is suppose to show 14.67VDC. I also have a 82 GPz550 Shindegen R&R which I wanted to "quickly" install and see if it would cut off/ground the voltage. Not so much, the 81 GPz/KZ550 R&R connector has male connectors while the 82 has female connectors and uses a different 6P connector to boot. To use the 82 R&R I pushed the terminals out but found I didn't have flat male connectors.



                              Do have 50 pairs of 4.00mm brass M/F bullet connectors.
                              Steve

                              1979 GS1000E (45 Yrs), 1981 GPz550 (11 Yrs)

                              Comment


                                Ed

                                To measure is to know.

                                Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

                                Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

                                Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

                                KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

                                Comment

                                Working...
                                X