Announcement

Collapse
No announcement yet.

Clutch actuator

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Clutch actuator

    Not sure if anyone else has already been over this in another thread but my clutch actuator I believe it is randomly let go of the cable lost the clutch needless to say so my question is does anyone have a picture of what it should look like or know of a place where I could source a new one for reference it is a 1985 gs300l. Thanks in advance
    Don't buy a 300 for normal riding you'll probably get bored

    #2
    Check the OEM parts fishe, such as on Partilla. The worm screw mechanism is same as the 450. They rarely fail. You may have some other problem. Did you pull the engine cover yet? If not, I'd do that. And make sure to use an impact driver on the screws or they may strip.
    Ed

    To measure is to know.

    Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

    Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

    Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

    KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

    Comment


      #3
      Yes I pulled the cover can't figure out how to upload a picture but the issue is the little riveted piece that the cable attached to broke and let go of the cable thanks for the info on it being the same as the 450. I checked partzilla and that didn't show any for a 300 I will look again for a 450. Is it the same as a 550 by chance I have one that I could borrow it from if so
      Don't buy a 300 for normal riding you'll probably get bored

      Comment


        #4
        Partzilla shows this PN. I did a search on ebay and got a couple of hits...23200-44101
        Ed

        To measure is to know.

        Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

        Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

        Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

        KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

        Comment


          #5
          Thank you I will do some digging and see if I can find it with the pn will keep posted I have found a few complete covers with one still attached on eBay was just hoping to be riding again a little sooner than shipping can take there
          Last edited by New GS guy; 07-02-2022, 10:44 PM.
          Don't buy a 300 for normal riding you'll probably get bored

          Comment


            #6
            Originally posted by New GS guy View Post
            Not sure if anyone else has already been over this in another thread but my clutch actuator I believe it is randomly let go of the cable lost the clutch needless to say so my question is does anyone have a picture of what it should look like or know of a place where I could source a new one for reference it is a 1985 gs300l. Thanks in advance
            Hi NewGS Guy..The cable end can fall out of these easily when cable is slack. It happens when you put the casing back on while lining it up to the Clutch Push pin ...so if you get a new one, use a bit of wire twisted cunningly to keep it all together while replacing cover... This might have been what B*ggrd original.

            Comment


              #7
              UPDATE:. Part is same on the 550 as well so I put the cable end and the actuator from the other bike in seems to be working fine put about 100miles on the bike yesterday and it worked fine (the adjustment on the back of the actuator was messing with me hard tho)
              Don't buy a 300 for normal riding you'll probably get bored

              Comment

              Working...
              X