O-rings in the full gasket set

[Guest]

Iv'e got the OEM full gasket set for my bike, inside there's a small bag with o-rings. i can identify the oil filter o-ring special shape, but clueless regarding the others.
hopefully the Collective Wisdom of the forum will have this knowledge.



Thanks
Eran

[Nessism]

I spy O-rings for:

Intake pipes
Cylinder liners
Crush washers for various plugs like drain pan plug
Oil passage under cylinder
various others.

[eran_k]

could there be the oil pump and cam chin tensioner in there as well?

[Nessism]

could there be the oil pump and cam chin tensioner in there as well?

Likely yes.

[BigD_83]

could there be the oil pump and cam chin tensioner in there as well?

Absolutely.

The cam chain tensioner gasket is the one on top.

[eran_k]

Well, there are still 3 that i don't recognize
all are around 30 to 32 mm and 2.5 to 3.1 mm thick
any ideas?
it's the oem gasket set

[Nessism]

Well, there are still 3 that i don't recognize
all are around 30 to 32 mm and 2.5 to 3.1 mm thick
any ideas?
it's the oem gasket set

Intake boot pipe O-rings might account for two of those. Dip stick O-ring? Gear position sensor O-ring?

Go though the fishe and look for O-rings...http://www.cmsnl.com/suzuki-gsx400-1...613/partslist/

[eran_k]

not the intake, already identified them as well as the oil pump o-rings
i was thinking that one of them is for the timing tensioner but seems too big
starter also has one i belive

[BigD_83]

I believe the 32x2.5 mm one is in the oil pan...I just ordered one and that sounded familiar. Looks like it is the same part (#8 and #29) in the 400 as the 550ES.

http://www.boulevardsuzuki.com/fiche_section_detail.asp?section=93060&category=Motorcycles&make=SUZUKI&year=1983&fveh=2108

[eran_k]

I took pictures of the ones I'm still not sure about,
i think the two tiny o-rings are for the oil passages at the top of the case. but what are the brass rings for?
the single o-ring in that picture has a rectangle rather the a round profile and it's around 16mm o.d

[BigD_83]

On your 400, do the float bowl drain screws have washers between the nut and the o-ring? Do you only have two of the brass gaskets?

Those small o-rings could also be for the drain screw, but their ID looks to be around 4mm, which would probably make them two small.

A flatter profile gasket makes me start thinking of things like the cam chain tensioner. It's a single o-ring, so drain caps (oil sump) and filler holes also make sense, although I do not think there is an o-ring on the oil pan, just a crush washer, and the filler cap does have a round profile, at least on the 550 and 650. Can't see Suzuki straying off that idea for the 400/450.

[eran_k]

On your 400, do the float bowl drain screws have washers between the nut and the o-ring? Do you only have two of the brass gaskets?

Those small o-rings could also be for the drain screw, but their ID looks to be around 4mm, which would probably make them two small.

A flatter profile gasket makes me start thinking of things like the cam chain tensioner. It's a single o-ring, so drain caps (oil sump) and filler holes also make sense, although I do not think there is an o-ring on the oil pan, just a crush washer, and the filler cap does have a round profile, at least on the 550 and 650. Can't see Suzuki straying off that idea for the 400/450.

There are only 2 brass washers. I just had a thought that they might be for the screws on the side of the intake ports.
one of the round o-rings can be for the oil filler, one could be for the gear position sensor and i think there's one in the oil pressure regulator (but i'm not splitting the cases to find out :-))

[BigD_83]

Yes, there are brass washers in the intake port plugs. Good call. They must be smaller than I thought.