1983 GS1100E Clutch parts questions

[adam83]

Im going to replace the friction discs and steels on my 83. I was planning on ordering OEM pieces, unless there is a better option? With OEM, there are 2 part numbers for friction discs, 1 for the D model, 1 for the Z model. I have the D model, but is there any benefit to using the Z model discs?

Are any other parts in this clutch setup that are known to get worn out at this age and should be replaced? For example, any of the springs, washers, wave washers, bearings etc?

Also, what is the unlabeled part between 16 and 17 on the diagram?

[rphillips]

that's the 1 steel plate goes between the wave washer (17) and the ring stopper (piano wire # 16). I'm thinking the Z plates are thinner and require 10 to be used instead of 9 as the D uses. But wait for verification on that.

[93Bandit]

I just replaced the frictions in my 83 850 and I used EBC plates because they are about half the cost of OEM. I've put a few hundred miles on them, so far so good. Several others on the forum have used EBC with success as well. I did not replace the steel plates because they looked fine. I would also replace the springs (item 12 in your image) if I were you, they're cheap and you've got it apart so you may as well replace them as well. I would just use OEM springs if your bike is stock.

[Grand Rouge]

I replaced the fiber discs in my owned since new 1100ED. The 83 had /has the extra fiber disc....one year only. The thinner metal core of the fiber discs do put grooves in the clutch basket...sometimes enough to require basket replacement. I installed Fast by Gast fibers. I re used original pressure plate springs, had basket properly riveted / welded and damper springs replaced etc. by Pearson Racing ...West Alexandria, Ohio

[adam83]

Thanks for replies. I'm a little confused, is it the Z that got the 10 fibers/steels, or is it the D? Or did both get 10? I'm assuming since there are different part numbers for the D and Z , that only one of them got the thinner disc's.

Grand Rouge, I've not heard of those brands/companies I'll have to check them out, and also inspect my clutch basket to see what you mean.

[Rijko]

The number of plates you need is in the picture you posted.

Yes, some aftermarket plates work, but if they damaged your clutch basket after a few thousand miles
you would be sorry.
Can't beat OEM, i'd look around for a good price, still to be found.

[bonanzadave]

EZ Clutch overhaul - The GSResources Forums

[joequesmith]

Im going to replace the friction discs and steels on my 83. I was planning on ordering OEM pieces, unless there is a better option? With OEM, there are 2 part numbers for friction discs, 1 for the D model, 1 for the Z model. I have the D model, but is there any benefit to using the Z model discs?
...

From what I remember, Suzuki stopped supplying the asbestos plates to the USA and the new OEM plates were not as good as their original. I was talking with Paul Gast about it and he had sorted out who the original supplier was and went directly to them in order to buy by bulk. He would show up at the track and you could buy as many as you wanted at basically cost. I don't believe he is in business anymore and suspect the only thing you can get are the newer OEM mix or aftermarket. I tried various aftermarket plates but they all have their problems.

That said, if your just using them with your stock street bike. No big deal.

plates.jpg

[joequesmith]

Different aftermarket plated viewed from the side. Not a fan of the top two, even for stock. The thicker aluminum substrate is going to be much easier on a stock basket.
plates1.jpg

[rphillips]

Thanks for that info. I'd think you couldn't mix them in the same hub??? or is the difference small enough you could adjust to workOK? I've replaced several plates, but don't remember dealing with this.

[joequesmith]

Thanks for that info. I'd think you couldn't mix them in the same hub??? or is the difference small enough you could adjust to workOK? I've replaced several plates, but don't remember dealing with this.

Assuming you mean mixing different aftermarket parts, I wouldn't recommend it.

The stackup for what I am doing is a bit more critical than for a street bike. I've ground steels for different thicknesses to get the height I want. Shown is the clutch for my GS, same era as yours. The plates shown came from Paul. I think I bought 50 or so last time. Note the custom feeler gauge with ball point pen used to check the stack.


plates2.jpg

[rphillips]

Thinking more about OEM plates. I now have an "83" (D) model bike with thinner plates. I have several older plates back there that are from earlier bikes, that will be the thicker plates. If I take my "83" clutch apart and find a couple, or 3, broken plates, can I just stick a couple, or 3 of those old, thicker, plates in there and be OK, or would it make the complete stack too thick (tall) to work properly on a stock bike? I know I have both older 1100 plates and GS1150 plates back there in the same pile, but never noticed the difference in thickness.

[bonanzadave]

I've not heard of those brands/companies

Fiber discs are 9.50 ea at Schnitz

FBG Clutch Fiber Suzuki GS1100-GS1150 - Schnitz Racing

[rphillips]

Seems strange, FBG doesn't distinguish between the 2 thicknesses for the GS1100's just say use 9 plates that would indicate they are the same as earlier thicker plates. It got me wondering so looking I found that Suzuki went back to the thicker plates for the GS1150's. It seems the thinner plates were for "83" GS1100 chain dr. models only.... Who'd have thunk that???

[adam83]

So if I wanted to order oem, but avoid the thinner 83 stuff, would I be good ordering steels and fibers for an 82 bike?