Announcement

Collapse
No announcement yet.

78 GS1000E - Rapping at 2000 RPM

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    78 GS1000E - Rapping at 2000 RPM

    Hello All,
    Today after a relatively hard down shift (went down two instead of one) I noticed a rapping sound at right around 2,000 RPM. It comes and goes - and if I were a guessing man, I'd say it sounds like the cams trying to switch between the low and high ranges. However, its new, and since I've put less than 1,000 miles on the bike since I've owned it - I'm not sure whats a huge problem and whats a minor issue.
    Is there a lube point up there that I"m missing? Have I just not gotten my cam chain adjusted right? (I haven't touched it) Or are my valves too tight and I'm just noticing it?
    I already found out I have a bad set of points - going to upgrade to electronic ignition - hope I haven't got another issue as well.
    Thanks in advance!
    -Joey

    #2
    Originally posted by SandPVRR View Post
    Hello All,
    Today after a relatively hard down shift (went down two instead of one) I noticed a rapping sound at right around 2,000 RPM. It comes and goes - and if I were a guessing man, I'd say it sounds like the cams trying to switch between the low and high ranges. However, its new, and since I've put less than 1,000 miles on the bike since I've owned it - I'm not sure whats a huge problem and whats a minor issue.
    Is there a lube point up there that I"m missing? Have I just not gotten my cam chain adjusted right? (I haven't touched it) Or are my valves too tight and I'm just noticing it?
    I already found out I have a bad set of points - going to upgrade to electronic ignition - hope I haven't got another issue as well.
    Thanks in advance!
    -Joey
    You know, you can guess all day, even take a stethoscope and listen to the insides, but if you want the peace of mind you seek, eventually you're going to have to check stuff out such as the valve clearances, and if you're not willing or able to do the work yourself, take it to the shop for a
    "tune-up."
    P.S. No lube points up there, just engine oil pumped up to that area (your oil pressure light isn't on, is it? and it does work?).
    Your cam chain is adjusted automatically by the automatic cam chain tensioner, you're not supposed to mess with it.
    Now a unfamiliar noise is a minor issue compared to a burned valve from too tight a clearance, but too much of a valve clearance and it could get get a little noisy. Is there any way you can find out when the valves
    were adjusted last? How's your oil level looking?
    sigpic
    Steve
    "The world is a book, and those who do not travel read only one page." :cool:
    _________________
    '79 GS1000EN
    '82 GS1100EZ

    Comment


      #3
      Originally posted by SandPVRR View Post
      It comes and goes - and if I were a guessing man, I'd say it sounds like the cams trying to switch between the low and high ranges.
      -Joey
      Where do you come up with this stuff? Cams don't switch anything

      Have you gone down the list of all the things you should check/adjust/update in your megawelcome?

      Two I'll suggest

      1. Adjust valves
      2. Service camchain adjuster
      1978 GS 1000 (since new)
      1979 GS 1000 (The Fridge, superbike replica project)
      1978 GS 1000 (parts)
      1981 GS 850 (anyone want a project?)
      1981 GPZ 550 (backroad screamer)
      1970 450 Mk IIID (THUMP!)
      2007 DRz 400S
      1999 ATK 490ES
      1994 DR 350SES

      Comment


        #4
        +1 on T's comment. How high did the RPMs go during this "downshift event"?
        http://img.photobucket.com/albums/v5...tatesMap-1.jpg

        Life is too short to ride an L.

        Comment


          #5
          Adjust the valves!
          sigpic

          82 GS850
          78 GS1000
          04 HD Fatboy

          ...............................____
          .................________-|___\____
          ..;.;;.:;:;.,;.|__(O)___|____/_(O)|

          Comment


            #6
            Is it conceiveable that you sheared a tooth on one of the gears? I have done that on British (Norton) gearboxes a couple times. It makes a knock which seems particularly noticable at steady RPM's.

            Bear in mind that on a normal motorcycle transmission all the gear sets are meshing all the time, so it does it in every gear, but especially the one with a tooth sheared off.

            If you over-revved it badly from downshifting, there is a number of things that could have gone wrong. Bending or breaking a valve would make it not run on that cylinder, which generally is quite noticeable.
            sigpic Too old, too many bikes, too many cars, too many things

            Comment


              #7
              Morning All,
              Update - Later, as I was riding home, I had to swing in and make one more stop for work. The bike sat in a parking lot for somewhere between a half an hour and an hour (not quite sure, but it was long enough that the engine was cooling and oil was showing up in the sight glass) It hasn't done that rapping sound since.
              It does still sound fairly noisy around 2000 RPM, but the sound goes away.
              Regarding my comment about variable valve timing - I could have sworn I read that in the service manual - however - I'm wondering if I skipped down to the Ignition timing page and didn't realize it at the time. My bad.
              -Joey

              Comment

              Working...
              X