flywheel puller source

[Guest]

I am looking for a puller for my flywheel, I am going to try and rent one if I can find a place that has one.
I found this one on ebay, its a 30mm but doesnt say it fits a gs1100/1150 Will this one work? I measured the threads at 30mm, but is there some other dimension of the puller that would make it not work?

http://www.ebay.ca/itm/Kawasaki-Suzuki-KLF-TM-Flywheel-Puller-30mm-x-1-5mm-/310354233347?pt=Motors_ATV_Parts_Accessories&hash=item48428dc803

[Souske]

For pulling the starter clutch?
Someone on here rents one

[quexpress]

I would ask them. They will certainly know because ... they have lots!

[willie]

I went through the same dilema last yr before buying a puller to access the starter clutch on my '82 1100GK. I just looked at it though and its 35mm, not 30. Recheck what you need and I'll loan you mine for the cost of postage if it'll work.
Willie

[blowerbike]

small taper crank=large threaded puller.
large taper crank=small threaded puller.
only large taper cranks was used in 83-86 1100/1150 16 valve engines.

[gearhead13]

small taper crank=large threaded puller.
large taper crank=small threaded puller.
only large taper cranks was used in 83-86 1100/1150 16 valve engines.

Yes I know, BB, its an '82 1100EZ with a large taper, welded crank
I pulled the cover off just to measure the threads and they are 30mm
Maybe someone swapped out the crank in this thing, idk
@ Willie Thanks, but I need a 30mm puller
Nowhere I have seen the 30mm puller does it say that it fits an 1100/1150

[quexpress]

Nowhere I have seen the 30mm puller does it say that it fits an 1100/1150

In December ... I have purchased a puller from that vendor which was identified as:
Kawasaki Suzuki GS Flywheel Puller (30mm X 1.5mm).

I also purchased another one from them identified as:
Honda Yamaha 350 Warrior Flywheel Puller[35mm x 1.5mm].

I have not used the 30mm one yet, but have used the 35mm one.

I would ask the vendor. They certainly know.

[bwringer]

There's a whole world outside fleaBay, you know.

Check Amazon -- that's where I've gotten a few of these. Or Dennis Kirk, or PitPosse.

Normally, the manufacturer's web site will have thread dimensions and photos. But you do have to verify things on your own -- there's very little solid info out there regarding exactly what fits what. You have to look under the stator cover.

Also, an awful lot of people confuse the chain drive 16V 1100E/ES and the shaft drive 8V 1100G/GL/GK.

[gearhead13]

There's a whole world outside fleaBay, you know.

Check Amazon -- that's where I've gotten a few of these. Or Dennis Kirk, or PitPosse.

Normally, the manufacturer's web site will have thread dimensions and photos. But you do have to verify things on your own -- there's very little solid info out there regarding exactly what fits what. You have to look under the stator cover.

Also, an awful lot of people confuse the chain drive 16V 1100E/ES and the shaft drive 8V 1100G/GL/GK.

I found one on Amazon, but they don't ship it to Canada
If they knew if it fit the gs1100/1150 why wouldnt they say that in the listing?

[blowerbike]

may i add that a non factory puller may get destroyed using it on the large taper cranks......
the big cranks are some bad mo-fo's to get the rotor's off.
i highly recommend a factory puller to use even if you have to beg or barrow/steal ect....

[blowerbike]

I found one on Amazon, but they don't ship it to Canada
If they knew if it fit the gs1100/1150 why wouldnt they say that in the listing?

because all they want is your money...no nothing sellers.
the 30mm does fit 1100/1150 even though the 1100 is an 83 only