Announcement
Collapse
No announcement yet.
Please help me understand and select chain and sprockets
Collapse
X
-
Originally posted by sedelen View PostsigpicMrBill Been a GSR member on and off since April 2002
1980 GS 750E Bought new in Feb of 1980
2015 CAN AM RTS
Stuff I've done to my bike:dancing: 1100E front end with new Sonic springs, 1100E swing arm conversion with new Progressive shocks installed, 530 sprockets/chain conversion, new SS brake lines, new brake pads. New SS fasteners through out. Rebuilt carbs, new EBC clutch springs and horn installed. New paint. Motor runs strong.
-
Forum LongTimerGSResource Superstar
Past Site Supporter- Oct 2006
- 13955
- London, UK to Redondo Beach, California
Paint the clip with bright paint (white) so you can easily see if it's missing & add a smear of silicone.
I use riveted & the same tool as Nardy above. To use the HF chain breaker you'd probably need to put something with a domed surface one side & a flat the other between the pin & the plunger. (You could easily make one out of a bolt or a piece of rod - I could sketch it if you like).
A lot of people use a punch with a rounded end & a hammer, striking onto a metal plate or the side of another large hammer.
1980 GS1000G - Sold
1978 GS1000E - Finished!
1980 GS550E - Fixed & given to a friend
1983 GS750ES Special - Sold
2009 KLR 650 - Sold - gone to TX!
1982 GS1100G - Rebuilt and finished. - Sold
2009 TE610 - Dual Sporting around dreaming of Dakar..... - FOR SALE!
www.parasiticsanalytics.com
TWINPOT BRAKE UPGRADE LINKY: http://www.thegsresources.com/_forum...e-on-78-Skunk/
Comment
-
littleroot
Got chain tool
Last night I ended up in Cycle Gear shop just to get some chain cleaner and lube and ended up coming home with THIS CHAIN TOOL because it was 60% off. They said I could return it if I didn't end up using it. Should I use it? I sent a note back to Mike at Z1 letting him know I got this so we can change the order to the rivet type of chain. My rear sprocket is on backorder so we have some time.
I took a photo of the tool still in the shrink wrap just in case the link breaks eventually. They had it for $34 only through January 2nd apparently but because they left the sign up the sales rep honored the price!
So what do you think?Last edited by Guest; 01-17-2013, 12:17 PM.
Comment
-
Originally posted by littleroot View PostLast night I ended up in Cycle Gear shop just to get some chain cleaner and lube and ended up coming home with THIS CHAIN TOOL because it was 60% off. They said I could return it if I didn't end up using it. Should I use it? I sent a note back to Mike at Z1 letting him know I got this so we can change the order to the rivet type of chain. My rear sprocket is on backorder so we have some time.
So what do you think?
It sounds like a lot of info but is simple once you figure it out.
Thanks,
JoeIBA# 24077
'15 BMW R1200GS Adventure
'07 Triumph Tiger 1050 ABS
'08 Yamaha WR250R
"Krusty's inner circle is a completely unorganized group of grumpy individuals uninterested in niceties like factual information. Our main purpose, in an unorganized fashion, is to do little more than engage in anecdotal stories and idle chit-chat while providing little or no actual useful information. And, of course, ride a lot and have tons of fun.....in a Krusty manner."
Comment
-
littleroot
Originally posted by Joe Nardy View PostI have seen this chain tool at Cycle gear and it appears identical to the Motion Pro tool except the case is red instead of blue. I was going to link to it in my previous post but saw it was listed at $89.99. I thought I had seen it for much less at the store or in sales emails. So you got it for around $36? If so, that's a good deal. Be sure to read and understand the directions before using. It can be a bit confusing the first time you use it. Be careful and don't over torque the tool, the threads can strip pretty easily. Also, it is helpful to have a caliper available when pressing the master link plate on and flaring the rivets. I measure the distance between plates and then slowly press the master link plate to the same distance. There is also a spec for how much to flare the rivets. Too much flare and you can crack the rivet and bind the chain, too little and it might pop off. I just did an RK chain on my XR600 and their website had info regarding the flare.
It sounds like a lot of info but is simple once you figure it out.
Thanks,
Joe
Comment
-
littleroot
Originally posted by salty_monk View PostPaint the clip with bright paint (white) so you can easily see if it's missing & add a smear of silicone.
I use riveted & the same tool as Nardy above. To use the HF chain breaker you'd probably need to put something with a domed surface one side & a flat the other between the pin & the plunger. (You could easily make one out of a bolt or a piece of rod - I could sketch it if you like).
A lot of people use a punch with a rounded end & a hammer, striking onto a metal plate or the side of another large hammer.
Comment
-
Any type of grinder will work.
Is your old chain/sprockets worn out?Last edited by tkent02; 01-17-2013, 12:56 PM.
Comment
-
Originally posted by littleroot View PostDumb question: I need to break the chain to get it off the bike, right? I remember the guy at the shop said he just uses a pneumatic cutting tool and I've been wanting to get one Harbor Freight?
Thanks,
JoeIBA# 24077
'15 BMW R1200GS Adventure
'07 Triumph Tiger 1050 ABS
'08 Yamaha WR250R
"Krusty's inner circle is a completely unorganized group of grumpy individuals uninterested in niceties like factual information. Our main purpose, in an unorganized fashion, is to do little more than engage in anecdotal stories and idle chit-chat while providing little or no actual useful information. And, of course, ride a lot and have tons of fun.....in a Krusty manner."
Comment
-
littleroot
Originally posted by tkent02 View PostAny tip of grinder will work.
Is your old chain/sprockets worn out?
Here is a picture of where I am on the adjuster on the swingarm. The labeled indicators are obvious but I'm not exactly sure what the indicator at the axle is telling me: could I have five more steps to go?
Comment
-
Those pictures mean nothing. Show us a pic of both sprockets, where the chain is not covering them. Are the teeth bent or hooked? Are the teeth all shaped the same?
And, pull the chain away from the sprocket at the point at the top of this picture. How far will it come away?
And, the two inches you can pull the chain down is normal, any less is too tight. The important part is that as you rotate the chain around the sprockets by turning the wheel, the two inches remains the same, not tight in one place and loose in another. The slack should be uniform, all the way around.
As you rotate the wheel, is the chain silent or does it snap and crackle as it goes around?
One more thing, are all of the O rings in the chain intact or are some of them missing?Last edited by tkent02; 01-17-2013, 01:05 PM.
Comment
-
littleroot
Originally posted by tkent02 View PostThose pictures mean nothing. Show us a pic of both sprockets, where the chain is not covering them. Are the teeth bent or hooked? Are the teeth all shaped the same?
And, pull the chain away from the sprocket at the point at the top of this picture. How far will it come away?
And, the two inches you can pull the chain down is normal, any less is too tight. The important part is that as you rotate the chain around the sprockets by turning the wheel, the two inches remains the same, not tight in one place and loose in another. The slack should be uniform, all the way around.
As you rotate the wheel, is the chain silent or does it snap and crackle as it goes around?
Comment
-
littleroot
Originally posted by littleroot View PostOK, good info. I will maybe shoot a video of me playing with it. The picture was meant to show where I was on the adjuster and get an answer to how I should interpret these. Mike from Z1 said because it has been converted to 530 already you don't always go by these indicators.
Comment
Comment