Announcement

Collapse
No announcement yet.

Would this fit?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Would this fit?

    I have a 1981 GS650, would an exhaust from a GS550 fit it?

    #2
    I'm not sure, but I have a 1980 550 and can take measurements if that would help.
    1980 GS550ET

    Comment


      #3
      Originally posted by steveb922 View Post
      I'm not sure, but I have a 1980 550 and can take measurements if that would help.
      That would be great thanks. Not sure what measurements I would need, but I presume center to center port spacing, center to center of the studs, I think on my 650 ports 1 & 4 are slightly angle out.

      Cheers

      Comment


        #4
        I'll go and take a look
        1980 GS550ET

        Comment


          #5
          Some quick measurements:-

          Downpipe flange OD - 36mm
          Stud centres - 62mm
          Ports 1 - 2 and 3 - 4 - 88mm to centres
          Ports 2 - 3 - 116mm to centres

          Ports 1 and 4 slightly angled out

          Caveat - the beer in the village inn was good last night. I'm happy to measure again if you think it's necessary!
          1980 GS550ET

          Comment


            #6
            http://www.thumbsnap.com/79UiHmNe
            See photo. Its my spare head, sorry its a bit fury!!
            Last edited by Guest; 12-08-2013, 09:05 AM.

            Comment


              #7
              I think I remember someone posting yesterday the the spacing is the same between the two engines but the diameter is different and won't seal up tight. Maybe a Seaking thread?

              cg
              sigpic
              83 GS1100g
              2006 Triumph Sprint ST 1050

              Ohhhh!........Torque sweet Temptress.........always whispering.... a murmuring Siren

              Comment


                #8
                Motad

                Hi, I have my Motad 4-1 currently off my 550ET and can take photos with tape measure if you think it will be of any help.

                Comment


                  #9
                  Originally posted by Charlie G View Post
                  I think I remember someone posting yesterday the the spacing is the same between the two engines but the diameter is different and won't seal up tight. Maybe a Seaking thread? cg
                  Not my thread, I'm following this one as well.. might be referring to it later

                  Comment


                    #10
                    Originally posted by Nicholk View Post
                    Hi, I have my Motad 4-1 currently off my 550ET and can take photos with tape measure if you think it will be of any help.
                    That would be great thank you as its a Motad I am looking at. I can get an exhaust in the UK for a 550 but not for a 650, I checked on the internet and according to the website there are only 2 GS650GTX 's on the road!!!!
                    Last edited by Guest; 12-08-2013, 04:30 PM.

                    Comment


                      #11
                      You can make a tube shaped spacer to make the 550 pipes fit the 650 ports, but as is they are a bit too narrow.
                      http://img.photobucket.com/albums/v5...tatesMap-1.jpg

                      Life is too short to ride an L.

                      Comment


                        #12
                        Looks like my problem has been solved, just found a second hand Motad 4 into 1 made for a GS650 for £35.

                        Comment


                          #13
                          Motad

                          Congrats....trying to photograph mine was not proving easy...was gonna have to get assistance....glad I don't have to.
                          Good luck

                          Comment

                          Working...
                          X