.png "Powered by vBulletin")
Hi, ... on an 81' GS750E , while my exhaust system is off with only breaking one exhaust clamp bolt, I was wondering if there would be any reason not to switch from bolts to studs, and if there wasn't, where might I be able to get some. Thanks, any opinion, or advice would be greatly appreciated... ray c. Ps. It is an original exhaust system.
-
Last edited by Guest; 02-02-2017, 11:33 PM. -
You can go either way. I prefer studs because there's less chance of stripping out the threads in the head - especially if you're removing the exhaust (semi) frequently.Current:
Z1300A5 Locomotive (swapped my Intruder for it), GS450 Cafe Project (might never finish it....), XT500 Commuter (I know - it's a Yamaha :eek:)
Past:
VL1500 Intruder (swapped for Z1300), ZX9R Streetfighter (lets face it - too fast....), 1984 GSX750EF, 1984 GSX1100EF (AKA GS1150)
And a bunch of other crap Yamahas.... -
I switched to studs on the exhaust for my 850. I was able to go down to the local NAPA, took one of the old bolts with me, and they hooked me up with a set of 8 studs that worked perfectly.Comment
-
Studs are easier to hang the pipe on . You won't crossbreed them either. I put locktite on mine so they don't back out with the nut.1981 GS650G , all the bike you need
1980 GS1000G Power corrupts, and absolute power corrupts absolutelyComment
-
Crossbreeding those studs with what??? I know, I know, cross threading.1981 GS 1000GLX.
1981 GS 1000G.
1981 GS 650GLX.
1975 TS 185.
1972 100. Kawasaki.
1968 100. Suzuki.
1970 Z 50. Honda.
1984 CT 70. Honda. (Kids)
1982 DS 50. Suzuki. (Kids)Comment
-
Suzuki part numbers give the diameter, and length. A stud would need to be longer, of course.sigpic Too old, too many bikes, too many cars, too many things
Comment
-
I believe that a 8mm x 50mm stud worked on my GS850 and GS1000 using a V&H exhaust.http://img633.imageshack.us/img633/811/douMvs.jpg
1980 GS1000GT (Daily rider with a 1983 1100G engine)
1998 Honda ST1100 (Daily long distance rider)
1982 GS850GLZ (Daily rider when the weather is crap)
Darn, with so many daily riders it's hard to decide which one to jump on next.;)
JTGS850GL aka Julius
GS Resource Greetings
Comment
-
Thanks, for the input guys, it didn't seem like there would be a problem, and the common 8mm size that they are, make them readily available at most hardware or supply stores, now that I see. thanks again... ray c.Comment
-
Something to remember is that you can only remove/install steel bolts in an aluminum head a number of times before something gets messed up. If it backs out on it's own, it might pull a few threads out with it aswell. Studs with lock-tight get my vote.
20160916_173742.jpgComment
-
You also want to use high temp anti-seize lubricant when installing them.http://img633.imageshack.us/img633/811/douMvs.jpg
1980 GS1000GT (Daily rider with a 1983 1100G engine)
1998 Honda ST1100 (Daily long distance rider)
1982 GS850GLZ (Daily rider when the weather is crap)
Darn, with so many daily riders it's hard to decide which one to jump on next.;)
JTGS850GL aka Julius
GS Resource Greetings
Comment
-
Install them into the head with threadlocker, use the anti seize on the nuts.Originally posted by JTGS850GL View Post1978 GS1085.
Just remember, an opinion without 3.14 is just an onion!Comment
-
Studs. Not bolts.NO PIC THANKS TO FOTO BUCKET FOR BEING RIDICULOUS
Current Rides: 1980 Suzuki GS1000ET, 2009 Yamaha FZ1, 1983 Honda CB1100F, 2006 H-D Fatboy
Previous Rides: 1972 Yamaha DS7, 1977 Yamaha RD400D, '79 RD400F Daytona Special, '82 RD350LC, 1980 Suzuki GS1000E (sold that one), 1982 Honda CB900F, 1984 Kawasaki GPZ900R
Comment
Comment