Announcement
Collapse
No announcement yet.
Hours to split case?
Collapse
X
-
Hours to split case?
Do any of you know how many hours it takes to split the cases on an 1100E and reassemble (in the bike)? I have been asked if I would perform this work and I don’t want to underestimate the price. The purpose is to fix an oil leak and address possible leaking valve.sigpic
1983 GS1100ES (Bought July 2014)
1983 GS1100E (Bought July 2014)
1985 GS700ES (Bought June 2015) Sold
On Christ the Solid Rock I Stand
All Other Ground is Sinking SandTags: None
-
Depending on where the oil leak is, you don't need to "split the cases".
On the other hand, it would depend on your terminology. To do anything with a valve, you DO have to remove the head. When you remove the head, it is highly recommended to remove the cylinders and replace the base gasket. Splitting the cases is usually only necessary to access the bits and pieces of the crank and transmission.
IF you have everything necessary, sitting on the bench, ready to go, AND have sufficient experience and/or training, a home mechanic might take 6-8 hours. A professional mechanic that has all the special tools necessary might do it a bit quicker.
I am in the middle of this process right now. Because of other things I am doing, it will be taking much longer, but I am not a professional mechanic and don't have all the special tools.
.sigpic
mine: 2000 Honda GoldWing GL1500SE and 1980 GS850G'K' "Junior"
hers: 1982 GS850GL - "Angel" and 1969 Suzuki T250 Scrambler
#1 son: 1986 Yamaha Venture Royale 1300 and 1982 GS650GL "Rat Bagger"
#2 son: 1980 GS1000G
Family Portrait
Siblings and Spouses
Mom's first ride
Want a copy of my valve adjust spreadsheet for your 2-valve per cylinder engine? Send me an e-mail request (not a PM)
(Click on my username in the upper-left corner for e-mail info.)
-
When I read "split the case" I read separating the bottom half of the engine from the top, so as Steve said, more clarification is needed.sigpic
When consulting the magic 8 ball for advice, one must first ask it "will your answers be accurate?"
Glen
-85 1150 es - Plus size supermodel.
-Rusty old scooter.
Other things I like to photograph.....instagram.com/gs_junkie
https://www.instagram.com/glen_brenner/
https://www.flickr.com/photos/152267...7713345317771/
Comment
-
Forum LongTimerBard Award Winner
GSResource Superstar
Past Site Supporter
Super Site Supporter- Oct 2003
- 17441
- Indianapolis
Originally posted by dorkburger View PostWhen I read "split the case" I read separating the bottom half of the engine from the top, so as Steve said, more clarification is needed.
You can remove the cylinder head and cylinders (the "top end") in the frame without splitting the cases.
But to split the cases (separate the bottom end halves), you must remove the engine from the frame.
You can replace the crankshaft and countershaft and some assorted other seals and o-rings without splitting the cases, so it's unclear what sort of oil leak might require this.
Or perhaps the OP means removing the cylinder head and cylinders, sometimes referred to as the "top end".
So Glib: what exactly is leaking and what work are we talking about here? You mentioned a valve, so can we assume you're talking about a top end?
If you've done it a couple of times before, I'd guess that the disassembly and assembly work of removing and replacing the cylinder head, cylinder, and pistons ("doing the top end") could be done in something like four to six hours, NOT including any cleaning, prep, or scraping. This is assuming you're organized, clean, and invisible gnomes make your parts magically clean the instant you put them down. (I bet the drag racers have this down to two hours or less...)
However, you'll spend at LEAST the same amount of time and probably a LOT more cleaning and scraping, depending on when the engine was apart last, and how well it was prepared at that time. Dealing with crusty diamond-hard 35 year old gaskets is the ridiculously tedious and time-consuming part of GS engine work. They're very simple engines, so disassembly and assembly are the fun, easy parts...
And I haven't even accounted for any time required to deal with broken bolts. If the engine hasn't been apart recently, it's a virtual certainty.
Not to mention all the time acquiring parts, etc. Getting the cylinders back onto the engine over the piston rings is possible with one person, but it's about 100x easier if you can recruit an assistant for a half hour or so.
If you're really talking about "splitting the cases" as in separating the bottom end case halves, then it depends on what you're in there to do. Plus, you can actually split the cases without removing the cylinder head, so perhaps that's an option.Last edited by bwringer; 07-23-2018, 09:55 AM.1983 GS850G, Cosmos Blue.
2005 KLR685, Aztec Pink - Turd II.3, the ReReReTurdening
2015 Yamaha FJ-09, Magma Red Power Corrupts...
Eat more venison.
Please provide details. The GSR Hive Mind is nearly omniscient, but not yet clairvoyant.
Celeriter equita, converteque saepe.
SUPPORT THIS SITE! DONATE TODAY!
Co-host of "The Riding Obsession" sport-touring motorcycling podcast at tro.bike!
Comment
-
Yes, the bottom halves is what I understood splitting cases to be, but wasn't clear enough. .....
There will be a case splitting in my future at some point. Case halves leak oil where they meet.sigpic
When consulting the magic 8 ball for advice, one must first ask it "will your answers be accurate?"
Glen
-85 1150 es - Plus size supermodel.
-Rusty old scooter.
Other things I like to photograph.....instagram.com/gs_junkie
https://www.instagram.com/glen_brenner/
https://www.flickr.com/photos/152267...7713345317771/
Comment
-
The leak is from the area between the lower cases where they are held together with Three Bond. A major operation to be sure. The bike owner believes that an exhaust valve is leaking also so that will need to be addressed as well.
It would be helpful to know what a professional would charge for comparison.sigpic
1983 GS1100ES (Bought July 2014)
1983 GS1100E (Bought July 2014)
1985 GS700ES (Bought June 2015) Sold
On Christ the Solid Rock I Stand
All Other Ground is Sinking Sand
Comment
-
Forum LongTimerGSResource Superstar
Past Site Supporter
Super Site Supporter- Mar 2006
- 35618
- Torrance, CA
Splitting the cases is major surgery. You have to remove the engine, fully tear it down, clean everything and replace gaskets/seals, etc. I'd estimate the amount of work for someone that's not a pro at about 30 hours, assuming you have the proper tools to do things like remove the valves, lap them, and replace valve stem seals. New rings are highly recommended too unless the bike is low mileage. Where you can really go sideways is if you run into stuck exhaust pipe bolts and hamfist the removal thus breaking them off. Other frustrations is fighting with carb boots that are hard and stiff. Stuff like that. It's no wonder most shops won't touch old bikes anymore.Ed
To measure is to know.
Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182
Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846
Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf
KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection
Comment
-
On a 1100E you can remove the engine and split the cases without removing the head/cylinders.
If the engine is out of the bike, I would say it is harder to remove the top end than split the cases. Of course, removing the engine involves some work which you have to do to split the cases.
I have several of the parts required for splitting the cases (I ended up fining all my GS1100ED leaks) so never did that.
Comment
-
Originally posted by posplayr View PostI have several of the parts required for splitting the cases (I ended up fining all my GS1100ED leaks) so never did that.
What parts are required? What would you estimate for time to complete?sigpic
1983 GS1100ES (Bought July 2014)
1983 GS1100E (Bought July 2014)
1985 GS700ES (Bought June 2015) Sold
On Christ the Solid Rock I Stand
All Other Ground is Sinking Sand
Comment
-
Originally posted by glib View PostWhat parts are required? What would you estimate for time to complete?
1 hour to get the clutch cover, clutch , counter sprocket and stator cover off
1 hour to get the base bolts out.
1 hour to split the case/ remove lower case
1 hour to clean the case facing surfaces
1 hour to order parts
1 hour to reassemble torque lower case.
1 hour to reassemble clutch and all covers
3 hours of drinking beer.
Round up to 10 hours including beer drinking time.
You can find the various parts needed in the parts finch.
Note without a special tool it is easier to break the clutch nut loose when the engine is in the bike.
Comment
-
Originally posted by posplayr View PostIf you have an engine out and on a bench (or engine stand),
1 hour to get the clutch cover, clutch , counter sprocket and stator cover off
1 hour to get the base bolts out.
1 hour to split the case/ remove lower case
1 hour to clean the case facing surfaces
1 hour to order parts
1 hour to reassemble torque lower case.
1 hour to reassemble clutch and all covers
3 hours of drinking beer.
Round up to 10 hours including beer drinking time.
You can find the various parts needed in the parts finch.
Note without a special tool it is easier to break the clutch nut loose when the engine is in the bike.
How long if drinking beer comes first?sigpic
1983 GS1100ES (Bought July 2014)
1983 GS1100E (Bought July 2014)
1985 GS700ES (Bought June 2015) Sold
On Christ the Solid Rock I Stand
All Other Ground is Sinking Sand
Comment
-
You should seriously consider getting a sizable deposit before starting in case it never gets picked up and you get stuck with a bike you will need to go through the lien process to be able to auction off for whatever it brings.....sigpic
09 Kaw C14 Rocket powered Barcalounger
1983 GS1100e
82\83 1100e Frankenbike
1980 GS1260
Previous 65 Suzuki 80 Scrambler, 76 KZ900, 02 GSF1200S, 81 GS1100e, 80 GS850G
Comment
Comment