Announcement

Collapse
No announcement yet.

81 GS750 Repaint

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    #31
    Niiiiiiiiiiiiiiiiiice paintwork!
    -KR

    Comment


      #32
      Originally posted by Bad Kaw View Post
      Niiiiiiiiiiiiiiiiiice paintwork!
      -KR
      Thanks all practice for my GSXR Street fighter

      Comment


        #33
        Originally posted by posplayr View Post
        Jim, can't seem to make this link work?? Would be Great to have that pdf.

        Thanks,
        Steve

        Comment


          #34
          Originally posted by HammerHead View Post
          Jim, can't seem to make this link work?? Would be Great to have that pdf.

          Thanks,
          Steve

          Steve
          Try these:
          Jim

          I uploaded a bunch of pics at photo bucket but now not sure how much resolution those will have.

          Bills has about 3-4 coats of clear but no RUNS

          http://s449.photobucket.com/albums/q...SR/Bills_Tank/

          Here are the ones for the GS750. It now has about 7-8 coats total but spraying in the colder weather (60 vz. the normal 85 deg) I got some runs even though it looks very wet. I need to work on them after it hardens a bit more.

          http://s449.photobucket.com/albums/q...SR/GS750_Tank/

          Comment


            #35
            Originally posted by posplayr View Post
            Beat the weather on Bill's bike
            Jim, no wonder the fumes make you a little crazy. How well does that Hornitos
            spray anyway???

            GREAT job on those strips on the 750. Love the red and orange together. The bike really
            looks bitchin
            Last edited by Guest; 01-02-2010, 01:53 AM.

            Comment


              #36
              Originally posted by HammerHead View Post
              Jim, no wonder the fumes make you a little crazy. How well does that Hornetos
              spray anyway???
              I usually do the Hornetos full strength .

              It doesn't usually atomize much coming through the throat of the bottle.

              Comment


                #37
                Originally posted by posplayr View Post
                Buffer the GS750EX; Paint on er is also done

                lol your selling out with all them valves! j/k nice bike
                John 3:16

                Comment


                  #38
                  Originally posted by GabrielGoes View Post
                  lol your selling out with all them valves!
                  Huh?............

                  Comment


                    #39
                    Originally posted by posplayr View Post
                    Huh?............
                    thats the model with 2 valves per cylinder right? so its a 16 valve bike! your selling out!
                    John 3:16

                    Comment


                      #40
                      Originally posted by GabrielGoes View Post
                      thats the model with 2 valves per cylinder right? so its a 16 valve bike! your selling out!
                      Sorry you have about 3 things wrong there so it is kinda killing the joke
                      1. 1981 GS750EX is a 16V TSCC engine
                      2. It has 4 valves per cylinder
                      3. If it was 2 valves per cylinder it would be an 8V not 16V.

                      Comment


                        #41
                        Originally posted by posplayr View Post
                        Sorry you have about 3 things wrong there so it is kinda killing the joke
                        1. 1981 GS750EX is a 16V TSCC engine
                        2. It has 4 valves per cylinder
                        3. If it was 2 valves per cylinder it would be an 8V not 16V.
                        thats totally what i ment
                        John 3:16

                        Comment


                          #42
                          Originally posted by GabrielGoes View Post
                          thats totally what i ment
                          OK then I'm really cornfused

                          Comment


                            #43
                            I went on one ride with Bill after his accident and rode the GS750. It was leaking quite a bit of oil so I ended up pulling the motor for a refresh which is something I had planned for some time. Now that I wrecked the ED, I had to do it to make more room before tearing down the ED .

                            I used the engine stand that I made. Not the best welding job but it sure makes working on the engine easier.

                            The engine ran well, despite it's 60K something miles. The PO had been into it but other than a clutch I was not sure what. I also had a spare parts bike that had some nice engine parts. So I'm swapping out some of those as listed below


                            Plans are to pull engine and:
                            • Cleaned most of the gunk to respray it with some Por-15 paint
                            • New OEM STD Rings (old ones measured out 0.,012" end gap)
                            • New OEM Head and Base Gasket
                            • New Viticon Valve Stem Seals
                            • Lapped valves
                            • Have nice set of GS1100E cams (15K miles and almost no wear)
                            • Nice set of GS750 82 Followers from Toto (Thanks they are nice)
                            • Plan on degreeing the cams
                            • Will bump the jetting up a bit as it is stock at the moment
                            • Split the cases to alleviate any oil leaks
                            • Putting a low mileage Transmission from the 80 GS750
                            • Putting a low mileage Clutch from the 80 GS750
                            • Cleaned carbon from the pistons and cleaned ring groves
                            • Buffed the pins and made sure they float nicely
                            • Changing out all of the bottom end rubber /seals with OEM
                            Got some other things planned once the motor is back in but, I need to finish this for now.

                            The photobucket slide show is here, But I'll post some with a brief description

                            Store your photos and videos online with secure storage from Photobucket. Available on iOS, Android and desktop. Securely backup your memories and sign up today!


                            Engine has been pulled and is on the stand.





                            Draining out all of the oil.



                            Pulling off the top end after a wash down.



                            flip motor over for the cases to get split



                            Bearings look decent






                            Tranny looks good but I have a spare with clutch

                            Last edited by posplayr; 05-07-2011, 11:10 PM.

                            Comment


                              #44
                              Went through the head to replace the guide seals and lap the valves. Most of the work is cleaning up the old carbon.






                              valve spring compressor worked like a charm. Just needed to clean blocks of wood to make it a one man operation.


                              Make sure you use a little grease when you assemble the keepers; makes it so much easier.



                              Head is nice an fresh; I use a hammer and socket to bounce the retainer a little to make sure the keeper doesn't fall out and it is secure. Head is also flat could not get a 0.005" feeler under a straight edge.



                              Last edited by posplayr; 05-07-2011, 11:29 PM.

                              Comment


                                #45
                                Did you check the rod bearings? They go first before the mains. My 750 mains looked better, but the rod bearings werent as good. I ended up just replacing the rod bearings.

                                Comment

                                Working...
                                X