Announcement

Collapse
No announcement yet.

Forks Polished

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
    #1

    Forks Polished

    Here's the before'n after. Got a nice satin finish, but polishing forks is a lot more work than I thought (they stayed on the bike throughout).

    I have a question for you guys: what grease is best for reassembly of the various nuts and bolts of the front wheel assembly? I have the following on hand. Copper based anti-seize (normally for engine bolts), teflon grease, lithium grease, 3-in-1 household oil, WD 40, motor oil.

    Before




    Halfway there! I used a 10mm metal rod clamped in place to keep the forks from rotating while I work on them. A piece of threaded rod would also work.



    Since there were no deep gouges on the forks, 400 grit wet sand paper was used to remove the clearcoat, cut into strips as such


    Once all the clearcoat was removed I polished using a cotton rotary wheel attached to my hand drill.

    After



    Here's what the small odds'n ends looked like before and after "treatment"

    Tags: None
    #2
    I usually put a thin layer of grease (lithium) on the front axle to minimixe corrosion & aid in the next removal...

    I use anti-sieze on anything threaded.
    '85 GS550L - SOLD
    '85 GS550E - SOLD
    '82 GS650GL - SOLD
    '81 GS750L - SOLD
    '82 GS850GL - trusty steed
    '80 GS1100L - son's project bike
    '82 GS1100G - SOLD
    '81 GS1100E - Big Red (daily rider)

    Comment

      #3
      You didn't actually polish that old bolt, did you?

      Comment

        #4
        Originally posted by makenzie71 View Post
        You didn't actually polish that old bolt, did you?
        Yes, I'm afraid I did..... and the washers too! This is the first time I restore a bike, and I fear it's becoming a bit of an obsession.
        Last edited by Guest; 03-16-2011, 02:34 PM.

        Comment

          #5
          Originally posted by hikermikem View Post
          I usually put a thin layer of grease (lithium) on the front axle to minimixe corrosion & aid in the next removal...

          I use anti-sieze on anything threaded.
          Ok hikermikem, thanks.

          Comment

            #6
            Looks GOOD!
            What did you use to polish? I did mine but the problem I have is they turned out too shiny.
            I like yours better!
            sigpic

            82 GS850
            78 GS1000
            04 HD Fatboy

            ...............................____
            .................________-|___\____
            ..;.;;.:;:;.,;.|__(O)___|____/_(O)|

            Comment

              #7
              Originally posted by GS Jim View Post
              Yes, I'm afraid I did..... and the washers too! This is the first time I restore a bike, and I fear it's becoming a bit of an obsession.
              Just exactly what I like to hear!!! Job well done.

              Comment

                #8
                Originally posted by GS Jim View Post
                Yes, I'm afraid I did..... and the washers too! This is the first time I restore a bike, and I fear it's becoming a bit of an obsession.
                I think obsession is a requirement for membership here, isn't it?

                Comment

                  #9
                  Go get a stainless bolt or all that work will quickly go to waste.

                  Comment

                    #10
                    WisGolfer59, these last few days, I've spent so much time in garage, the pooch is moving in with me!

                    Octain, I first tried normal polishing compound, but like you found it resulted in a shinier finish than I wanted. I sanded again lightly with 600 grit and applied some liquid aluminum polish to the fork with a brush. After letting it dry to a semi-liquid state (about 5 mins) I then hit it with the cotton polishing wheel. The results were closer to the satin look I was aiming for.

                    Comment

                      #11
                      Looks good, but I have to confess, I went for the high sheen on mine.

                      Comment

                        #12
                        Originally posted by makenzie71 View Post
                        Go get a stainless bolt or all that work will quickly go to waste.
                        He has a very good point. I know oh too well. For a year or more I used steel wool followed by WD40 to keep the rust off for a short time but on my recent build I spent the money and had ALL the bolts, spacers, washers, etc., Cadmium plated, a bit of money but well worth it. Some guys spray paint and cook them with good results, some clear coat but not sure how that turns out. Bikes looking very good, is it still coming across the water to Canada this year?
                        Rob
                        1983 1100ES, 98' ST1100, 02' DR-Z400E and a few other 'bits and pieces'
                        Are you on the GSR Google Earth Map yet? http://www.thegsresources.com/_forum...d.php?t=170533

                        Comment

                          #13
                          AZR, tks for the comments, I have replaced with stainless when I can find the right sizes locally, even cut a few bolts to size on occasion, but the caliper bolts are a weird size I couldn't find.

                          Also this bike won't be ridden in the wet or in winter once its done, I have the honda for that.
                          Yeah, the bike is definitely coming across the pond with me this summer. Wifey is presently in Toronto house hunting, so I have the garage all to myself, hehe.

                          Comment

                            #14
                            Nice job

                            The best way I found to achieve satin finish is to start out with wet/dry paper from 400, then 600, 800, 1000, 1500 and finish with 2000 Gives an awesome satin finish!

                            I have also successfully used clear 2pak (urethane) paint over freshly polished alloy.
                            It maintains the surface of the alloy, be it high mirror finish or satin/anodised and it is extremely durable even to stone chips and road grime!
                            Regards,
                            Andy
                            Queensland Australia

                            http://i117.photobucket.com/albums/o...h_PIC00011.jpg
                            GS750B (1977)
                            Wiseco 850 kit, K&N pods, 4-1 transac, Custom 2 pak paint, IKON shocks, Custom L.E.D light boards (turn + stop/tail + dash)

                            Comment

                              #15
                              I remove the clear coat with paint stripper. Takes 5 minutes.

                              Then we go 220, 400, 600 and finally steel wool to get that satin finish.

                              I degrease with lacquer thinner and clear coat with clear engine paint.

                              Good for few years.
                              1981 GS650G , all the bike you need
                              1980 GS1000G Power corrupts, and absolute power corrupts absolutely

                              Comment

                              Previous template Next
                              Working...
                              X