Announcement

Collapse
No announcement yet.

Pilot jets

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Pilot jets

    Just thought i would mention that although i have stripped the carbs cleaned and rebuilt them with new seals its been a learning curve and something that i did not know or overlooked in the tutorials on here .
    Cleaning every orifice is obviously key which i thought id done . However after looking at a number of ytube videos i did not realise that the pilot jets have a pin hole in the bottom that is notorious for getting blocked . This has been the problem with my GS850G from the start . After soaking the jets in carb cleaner for days and using a single wire from a wire brush i cleared the fine hole in the bottom of all the jets . They were totally blocked solid in the bottom fine holes but clear in the side holes .
    Was there ever an upgrade on these jets to stop the blockages or is it just normal for them to become clogged after so many miles ?

    #2
    There is no upgrade.
    Providing the bike is run regularly and the tank and fuel lines are free from debris etc they rarely give any trouble.
    Occasionally one may get a partial blockage which usually clears on the run but for all four to become blocked is nearly always the result of the carbs being laid up for a long period of time.
    Mikuni Viton Choke Plunger Seat Renewal.
    VITON Choke plunger seals .KAWASAKI Z1,Z900,Z650,Z1000,Z1R,SUZUKI GS1000,GSXR,RF | eBay

    Air Corrector Jets for Mikuni VM 24, 26 and 28mm carbs .
    https://www.ebay.co.uk/itm/254380193...84.m1555.l2649



    sigpic

    Comment


      #3
      Screenshot 2024-11-03 040822.png
      Last edited by Nessism; 11-03-2024, 08:09 AM.
      Ed

      To measure is to know.

      Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

      Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

      Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

      KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

      Comment


        #4
        When i got the bike the carbs were not on the bike so assuming these were off a long time or even off another bike that had stood for years . Lesson learnt for the future but at least im up to scratch on total carb rebuilds .
        Thanks to all

        Comment


          #5
          Was there any noticeable change in performance after cleaning those jets?
          Current Bikes
          1980 Suzuki GS 1000G
          1973 Suzuki GT 185 (The tiddler)
          "Live to die, die to live"

          Comment


            #6
            Originally posted by Syd View Post
            Was there any noticeable change in performance after cleaning those jets?
            Im going to put the bike together later in the week so will update you Since owning this bike ive had to re wire everything from scratch then rebuild the carbs fully a few times without success .
            Clearing these blocked pilot jets will be the last job hopefully and get the bike running .

            Comment


              #7
              Originally posted by Syd View Post
              Was there any noticeable change in performance after cleaning those jets?
              With the pilot jets plugged, the bike will run like garbage.
              Ed

              To measure is to know.

              Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

              Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

              Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

              KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

              Comment


                #8
                Im really struggling with these carbs . Every orifice was cleaned and blown out with air , new seals throughout and still it will only run on choke . All i can think of is those tiny holes in the end of the pilot jets have blocked again ? Any other ideas greatly received ?

                Comment


                  #9
                  Well, logic leads one to the fact that the carbs are not clean, otherwise your bike would be idling and running.

                  Did you follow the carb cleaning tutorial?
                  1978 GS 1000 (since new)
                  1979 GS 1000 (The Fridge, superbike replica project)
                  1978 GS 1000 (parts)
                  1981 GS 850 (anyone want a project?)
                  1981 GPZ 550 (backroad screamer)
                  1970 450 Mk IIID (THUMP!)
                  2007 DRz 400S
                  1999 ATK 490ES
                  1994 DR 350SES

                  Comment


                    #10
                    Originally posted by Big T View Post
                    Well, logic leads one to the fact that the carbs are not clean, otherwise your bike would be idling and running.

                    Did you follow the carb cleaning tutorial?
                    Oh yes followed the tutorial exactly . All 4 carbs were separated and new seals on everything . Ive got them off again and checked it all and nothing is blocked or wrong . The only thing that was a bit suspect to me was that when putting the float bowls back on there was some resistance , maybe hanging up on the pilot jet bungs and could be dislodging them leaving them open but will check those today .

                    Comment


                      #11
                      this may be a suggestion easy to dismiss ... but have seen a number of float bowl gaskets recently that are too large on the float sides.
                      Rubbing the floats, preventing movement.
                      So one carb would starve, while the next carb would be stuck in float needle open position.
                      Are you sure the floats are moving freely ?

                      side note chuck hahn could this be a cause for your plugs fouling ?
                      Last edited by Rijko; 11-20-2024, 07:17 PM.
                      Rijk

                      Top 10 Newbie Mistakes thread

                      CV Carb rebuild tutorial
                      VM Carb rebuild tutorial
                      Bikecliff's website
                      The Stator Papers

                      "The thing about freedom - it's never free"

                      Comment


                        #12
                        Originally posted by Rijko View Post
                        this may be a suggestion easy to dismiss ... but have seen a number of float bowl gaskets recently that are too large on the float sides.
                        Rubbing the floats, preventing movement.
                        So one carb would starve, while the next carb would be stuck in float needle open position.
                        Are you sure the floats are moving freely ?

                        side note chuck hahn could this be a cause for your plugs fouling ?
                        Hi your theory about the gaskets was correct . 2 of the 4 were rubbing . Will test to see if this helps .
                        One thing i notice was that the rubber bungs over the pilot jets where different hights than the other 2 . Maybe not sealing correctly once the bowls are put back on ?
                        Have ordered some new bungs .

                        Comment

                        Working...
                        X