Black/Wet Plugs

[GabrielGoes]

Hey guys i was just confused today because i thought i finally got my bike running good and then all of the sudden it lost a lot of power and started running really rich like it had problems reving in all RPM ranges... i was like **** i thought the problems were all over (HA)

so i pulled the choke while riding and then went back to no choke- did this like 4 times and my bike was running decent again but sounded rich and when i checked plugs at home it was black/wet... do you guys think that running a full can of seafoam can make this happen? do i need a carb rebuild kit you think?

[BassCliff]

Hi,

This is from your "mega-welcome". How many items on these maintenance lists have you completed?
----------

Perhaps you've already seen these, but I like to remind all the new members. In addition to the carb rebuild series, I recommend visiting the In The Garage section via the GSR Homepage and check out the Stator Papers. There's also a lot of great information in the Old Q&A section. I have some documentation on my little BikeCliff website to help get you familiar with doing routine maintenance tasks (note that it is 850G-specific but many tasks are common to all GS bikes). Other "user contributed" informational sites include those of Mr. bwringer, Mr. tfb and Mr. robertbarr. And if your bike uses shims for valve adjustments, send an email to Mr. Steve requesting a copy of his Excel spreadsheet that helps you keep track of clearances, shim sizes and other service work.

These are some edited quotes from one of our dear beloved gurus, Mr. bwringer, with ideas on basic needs (depending on initial condition), parts, and accessories.

***********Quoted from Mr. bwringer************
Every GS850 [and most other models] has (or had) a set of well-known issues that MUST be addressed before you have a solid baseline for further troubleshooting. It's a vintage bike, and it's quite common (as in, every single GS850 I have had contact with) that there are multiple problems that have crept up and slowly gotten worse over the years. It's not like a newer vehicle, where there's generally one problem at a time.

These common issues are:

1. Intake O-rings (install NEW OEM or Viton only - common nitrile O-rings will quickly deteriorate from heat)
2. Intake Boots (install NEW -- these cannot be repaired)
3. Valve clearances (more important than most people think)
4. Carb/airbox boots
5. Airbox sealing
6. Air filter sealing
7. Petcock (install a NEW one)
8. On '79 models, install new points or Dyna electronic ignition (or at least verify that the old points are working correctly)
9. On all models, it's fairly common to have problems with the spark plug caps. These are $3 or $4 each, and often worth replacing if you're keeping the stock coils/wires.
10. Stock exhaust with NO leaks or holes -- good seals at the head and at the junctions underneath.

What I have noticed at the rallies is that very, very few 850Gs are actually running right. Make VERY sure it's actually running the way it's supposed to before busting out the modifications.

Brian's E-Z and fun plan for GS850 happiness:

1) Seal the airbox and air filter with weatherstripping.

2) Ensure no intake leaks. Spraying WD-40 or water doesn't tell you much, since very small air leaks can cause problems even though they won't suck in enough WD-40 to make a difference. Replace your intake boot o-rings and boots if needed, and seriously consider spending the lousy $28 for new airbox/carb boots.

3) Ensure clean carbs with correct settings, new o-rings, and original OEM jets. No, not just squirted with something. I mean completely disassembled.

4) Check/adjust valve clearances (Manual calls for every 4,000 miles. This is not optional.)

5) Ensure healthy electrical system.

6) Seriously consider upgrading coils and plug wires.

7) Install new, stock NGK B8-ES plugs gapped to .031".

8 ) Fine-tune float height and idle mixture screw to ensure best off-idle transition.

9) Clean air filter and reinstall with only the lightest oil mist -- over-oiling and/or letting the filter get dirty is a common and critical mistake, and will make the bike run funny at low speeds and run rich. This may take a few tries.

10) Make sure the exhaust seals are sealing.

11) Ooh, much better now, huh? You're gonna need upgraded suspension - Progressive or better fork springs and shocks. Set suspension sag appropriately.

12) Upgrade brakes with new pads and stainless lines to deal with all that extra speed.

13) Install new petcock, since I'm going to head to the roof with a rifle if I have to read about yet another #2 plug fouling and failed hillbilly attempts to rebuild the petcock and/or deny there's a problem.

14) Oh yeah -- check compression somewhere in there to ensure the valves and rings are reasonably healthy.

15) You'll probably need new OEM clutch springs -- the clutches last forever, but the springs get tired after 20 years or so under pressure. E-Z and cheap.
Carburetor maintenance:

Replace the intake boot o-rings, and possibly the intake boots. Here's the procedure:

http://bwringer.com/gs/intakeorings.html

Here's an overview of what happens with this particular problem:

http://cycleorings.com/intake.html

You'll also want to examine the boots between the carbs and the airbox. There's a good chance these are OK, but check them over.
And finally, if things still aren't exactly right, you'll want to order a set of o-rings for BS carbs from the GS owner's best friend, Robert Barr:
http://cycleorings.com
Once you receive these rare rings of delight, then you'll want to thoroughly clean and rebuild your carburetors. Here are step-by-step instructions that make this simple:

http://thegsresources.com/gs_carbrebuild.htm

----------------------------------


Thank you for your indulgence,


BassCliff