Announcement

Collapse
No announcement yet.

81 750 #2 pipe cold and plug wet

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    81 750 #2 pipe cold and plug wet

    the bike runs but #2 cylinder pipe is cold and gas comes out of the exhaust i was thinking it might be a bad petcock, so i disconnect the vacuum line and plug it with a screw. put the petcock on prime and start her up.

    well gas kept comeing out of the exhaust and thats when i noticed the petcock is ****ing all over my shoe... looks like i need a new petcock? maybe i should have let it run longer and see if no 2 heats up?

    are the rebuild kits any good or should i save myself the hassle and just buy a new one?

    #2
    Buy a new one

    Comment


      #3
      Originally posted by FreshStart View Post
      Buy a new one
      Yep, the consensus here is that the rebuild kits are iffy!
      1981 gs650L

      "We are all born ignorant, but you have to work hard to stay stupid" Ben Franklin

      Comment


        #4
        See your "mega-welcome"

        Hi,

        Here's an excerpt from your "mega-welcome", just in case you missed it.

        ------------------------------

        ***********Quoted from Mr. bwringer************
        Every GS850 [and most other models] has (or had) a set of well-known issues that MUST be addressed before you have a solid baseline for further troubleshooting. It's a vintage bike, and it's quite common (as in, every single GS850 I have had contact with) that there are multiple problems that have crept up and slowly gotten worse over the years. It's not like a newer vehicle, where there's generally one problem at a time.

        These common issues are:

        1. Intake O-rings (install NEW OEM or Viton only - common nitrile O-rings will quickly deteriorate from heat)
        2. Intake Boots (install NEW -- these cannot be repaired)
        3. Valve clearances (more important than most people think)
        4. Carb/airbox boots
        5. Airbox sealing
        6. Air filter sealing
        7. Petcock (install a NEW one)
        8. On '79 models, install new points or Dyna electronic ignition (or at least verify that the old points are working correctly)
        9. On all models, it's fairly common to have problems with the spark plug caps. These are $3 or $4 each, and often worth replacing if you're keeping the stock coils/wires.
        10. Stock exhaust with NO leaks or holes -- good seals at the head and at the junctions underneath.


        What I have noticed at the rallies is that very, very few 850Gs are actually running right. Make VERY sure it's actually running the way it's supposed to before busting out the modifications.


        Brian's E-Z and fun plan for GS850 happiness:

        1) Seal the airbox and air filter with weatherstripping.

        2) Ensure no intake leaks. Spraying WD-40 or water doesn't tell you much, since very small air leaks can cause problems even though they won't suck in enough WD-40 to make a difference. Replace your intake boot o-rings and boots if needed, and seriously consider spending the lousy $28 for new airbox/carb boots.

        3) Ensure clean carbs with correct settings, new o-rings, and original OEM jets. No, not just squirted with something. I mean completely disassembled.

        4) Check/adjust valve clearances (Manual calls for every 4,000 miles. This is not optional.)

        5) Ensure healthy electrical system.

        6) Seriously consider upgrading coils and plug wires.

        7) Install new, stock NGK B8-ES plugs gapped to .031".

        8 ) Fine-tune float height and idle mixture screw to ensure best off-idle transition.

        9) Clean air filter and reinstall with only the lightest oil mist -- over-oiling and/or letting the filter get dirty is a common and critical mistake, and will make the bike run funny at low speeds and run rich. This may take a few tries.

        10) Make sure the exhaust seals are sealing.

        11) Ooh, much better now, huh? You're gonna need upgraded suspension - Progressive or better fork springs and shocks. Set suspension sag appropriately.

        12) Upgrade brakes with new pads and stainless lines to deal with all that extra speed.

        13) Install new petcock, since I'm going to head to the roof with a rifle if I have to read about yet another #2 plug fouling and failed hillbilly attempts to rebuild the petcock and/or deny there's a problem.

        14) Oh yeah -- check compression somewhere in there to ensure the valves and rings are reasonably healthy.

        15) You'll probably need new OEM clutch springs -- the clutches last forever, but the springs get tired after 20 years or so under pressure. E-Z and cheap.
        --------------------------------------------------

        Thank you for your indulgence,

        BassCliff

        Comment

        Working...
        X