Rule #11

[BassCliff]

Hi,

Check the "Services" section of the forum. There is a Shim Club that trades shims. Z1 sells individual shims for less than $6 each, no need to buy a whole kit (which probably contains many sizes you can't use anyway).

Z1 also sells the tappet tool. Just click the picture.




Thank you for your indulgence,

BassCliff

[mighty13d]

if you do want to run a filter, you have to make sure that it is a low pressure filter. A lot of filters are for fuel injected lines and won't flow without pressure behind them. I hope things get sorted out. I am enjoying this write up though.

Also, as was mentioned, did you check the kill switch? It's something that pretty well everyone has done at one time or another. I hit it when I went to take my test for my license........ (we do them on the road here in Maine and the instructor follows in their car and beeps at you to tell you what to do) Anyway, he just went with someone else and I took mine after that. I lied and told him that the ignition must have been acting up... lol

So give a once over to your electrical connections since it's easy to pull something apart and not notice it. And check your kill switch.

You mentioned that your turn signal switch isn't working right. You can just replace it pretty easily. I got an almost brand new set of controls from a Suzuki Bandit off E-bay for $10 or something ridiculously cheap like that. They have a little plastic nub that needs to be cut off (or a corresponding hole drilled into the bars. The nub is there to keep them from twisting although I have not had any issues without it) and I think I had to cut the original plugs off and wire those onto my new controls. The plug from the end that is in the headlight. It was really easy, all the wires matched up because I got it from another Suzuki. It works beautifully too since they are pretty well brand new. I hope this helps. A lot of people are against it and keep saying to use stock ones, but that is ignorant. The 30+ year old ones were not great to begin with and time hasn't helped. Do yourself a favor and consider this. It will be cheaper and better (but not easier since you will need to wire up the original plug onto the new one).

[tkent02]

I set my air screws @ 1-1/4 turn and my fuel pilots at 1 turn.

Generally as a starting point the fuel screw is opened half as far as the air screw. Just a preliminary seeing of course, it will need to be fine tuned once it's running.

[andtheacademics]

Hi,

Check the "Services" section of the forum. There is a Shim Club that trades shims. Z1 sells individual shims for less than $6 each, no need to buy a whole kit (which probably contains many sizes you can't use anyway).

Z1 also sells the tappet tool. Just click the picture.




Thank you for your indulgence,

BassCliff

Doesn't this mean I'll have to first feel out the shims and then sit around and wait for the correct ones to arrive? Or do you guys all put the bike back together and continue to ride uncalibrated?

I'm starting to think I should have just bought one of these...

...They have a little rattle at the top end, but if you install some improved fork dampeners it usually takes care of it.

Also, just found the "For Sale" section of this forum, which is only added proof that I paid about triple what this bike is actually worth! @%$&!

[andtheacademics]

Generally as a starting point the fuel screw is opened half as far as the air screw. Just a preliminary seeing of course, it will need to be fine tuned once it's running.

Noob question - how do you turn the fuel screws with the bike running? Do i have to buy a tiny screwdriver and a dentists mirror?

Also - no springs on my fuel pilots - problem??

[tkent02]

Noob question - how do you turn the fuel screws with the bike running? Do i have to buy a tiny screwdriver and a dentists mirror?

Tiny screwdriver, yes, mirror, no. You can do it by braille. Wear a thin glove, that engine gets hot. I use a short screwdriver tip for a drill, stuck in a 1/4" socket as my screwdriver.

(I think it's 1/4, whatever size fits it)

Also - no springs on my fuel pilots - problem??

Yes, there should be springs like the ones on the air screws, only smaller.

Or do you guys all put the bike back together and continue to ride uncalibrated?

I do this, unless one is too far out of spec to be safe.

[andtheacademics]

Yes, there should be springs like the ones on the air screws, only smaller.

So - where can I buy new ones? Seems like a rather tiny part...

EDIT: Nevermind, asked a dumb question before looking hard enough - boulevard has them, - although there are two different carb models for 78 GS750 and I can't find a spring on one of them

[tkent02]

Bic makes some close enough in diameter.
Might have to loosen or tighten them up just a tad. Can't remember which.

[BassCliff]

Hi,

Doesn't this mean I'll have to first feel out the shims and then sit around and wait for the correct ones to arrive? Or do you guys all put the bike back together and continue to ride uncalibrated?

That's up to you. I think the shim club (Ray) will send out the necessary shims in advance with a promise that you return the ones you no longer need, one for one.

Getting the valves in spec the first time seems to always take the longest. Once they are in spec, and you know the current clearances and shim sizes, it will be quicker the next time because, with a little forethought, you can have the shims needed for your next check already on hand.

Since I have inventoried my shims and clearances, keeping a record in Steve's handy-dandy spreadsheet, I can "guess-timate" what shims I might need at my next valve check and order ahead. I now have a small collection of shims that should keep me running for the next few years.

You'll find a shim worksheet on my website. Send Steve an email to get a copy of his service spreadsheet.

Thank you for your indulgence,

BassCliff

[andtheacademics]

I can "guess-timate" what shims I might need at my next valve check and order ahead. I now have a small collection of shims that should keep me running for the next few years.

Again, psychic powers appear to prevail...

But the first time is the hardest - so I have to go through the process (measure clearances, pull out what shims are existing there already, calculate what I need to replace them with for correct clearances) Contact Mr. Ray, Esq. get supplement shims, and then send Mr. Ray, Esq. 'spent' shims... I may be better served to buy the first eight or so - that way I can begin building a back stock like Mr. BassCliff...?

Now - this might seem obvious to you pros, but you are in fact measuring the distance between the underside of the LOBE and the SHIM with a FEELER GAUGE? And you want there to be some room for play to reduce friction/ resistance on the camshafts?

And, out of curiosity does anyone know of a clear fuel line? They guy at the hardware store said they don't exist and the tubing he sold me can only have gas in it for a short while before it disintegrates....

[BassCliff]

Hi,



Have you gone through the guide?

Valve Adjustments (8 Valve)

I would also suggest getting a true metric feeler gauge and not an SAE gauge with equivalents on the back. As for my "psychic powers", if most of my clearances are at .07mm-.09mm but then I have a couple that are .04mm-.05mm then I will order replacements for those shims (the next size smaller) ahead of time. Once you've gone completely through the procedure once or twice you will realize how simple it is. I promise.

If you'd like to just buy one size smaller for each of the shims you have, I guess that would be a good place to start. Keep in mind that valve clearances tend to get smaller over time so the larger sizes will eventually become unusable.

Clear fuel line: http://www.z1enterprises.com/detail.aspx?ID=297


Thank you for your indulgence,

BassCliff

[tkent02]

Again, psychic powers appear to prevail...

No psychic powers needed, they will generally wear tighter, needing the next size thinner shim. If you know what is there now, and which valves are getting close to the limit, you know what will be needed next. Steve's spreadsheet is great for this.

And you want there to be some room for play to reduce friction/ resistance on the camshafts?

This isn't it, although if there were no gap at all, the oil would be wiped off the cam and there would be wear problems...

The valves only cool themselves by contact with the valve seat... If the adjustment is too tight it doesn't really contact the seat as it should, so the valve starts to get hot. With the heat the valve expands, it becomes longer. Now it closes even less, and contacts the seat even less, getting even hotter. Vicious circle, heat causes less contact, less contact causes more heat. Eventually it gets so little contact with the seat, that it can't cool at all, gets hotter and hotter, and finally some metal burns away from the edge of the valve. Now flames are squeezing through the this gap in the valve, giving the valve even more heat. Soon the nice round valve head looks like a pizza with a piece missing, the engine can no longer run on that cylinder, and you have a lot of expensive work to do.
Like this:

And, out of curiosity does anyone know of a clear fuel line? They guy at the hardware store said they don't exist and the tubing he sold me can only have gas in it for a short while before it disintegrates....

Bike shops used to have it, can't find it lately.

[MisterCinders]

You can get 1/4 inch clear line from Z1 for a buck a foot. It is tight on the petcock and fuel tee, but works fine.

You can also try buying one or two shims from your local bike shop. I get them for $5 each from a place nearby. Buy a single shim on the thin side - maybe 2.50. Then you have a spare placeholder, allowing you to swap shims across your valves to the extent you can trade a big clearance for a small one. Then go back to the bike place and buy the shims you need to finish out.

When I first did the valves on my bike I only needed to buy like two shims

[andtheacademics]

The valves only cool themselves by contact with the valve seat... If the adjustment is too tight it doesn't really contact the seat as it should, so the valve starts to get hot. With the heat the valve expands, it becomes longer. Now it closes even less, and contacts the seat even less, getting even hotter. Vicious circle, heat causes less contact, less contact causes more heat. Eventually it gets so little contact with the seat, that it can't cool at all, gets hotter and hotter, and finally some metal burns away from the edge of the valve. Now flames are squeezing through the this gap in the valve, giving the valve even more heat. Soon the nice round valve head looks like a pizza with a piece missing, the engine can no longer run on that cylinder, and you have a lot of expensive work to do.

EUREKA! NOW I GET IT! So if everyone in agreement that the shims on these engines are consistently needing to be replaced by thinnner and thinner ones, wouldn't that lead you to assume the valves are getting longer over time? Meaning you eventually have to replace your valves all together?

When someone says "Rebuilt Engine," That is the type of work I had assumed they are doing... I guess it takes making that mistake once to learn that lesson!

Thanks again everyone for the (continued) help and explanations! This forum really is an invaluable resource, once I finish filling the hole in my bike with money, I'll be sure to send some to the administrators!

[DannyMotor]

You can get 1/4 inch clear line at ANY hardware store, and most auto-parts stores. Check lawn-and-garden by the lawnmowers/oil/filters/etc...