Announcement

Collapse
No announcement yet.

1981 GS1100E Idles ok. Turn throttle instant death.

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    1981 GS1100E Idles ok. Turn throttle instant death.

    Any ideas?

    #2
    none...

    but what have you done lately to the bike, clean the carbs, new O rings etc, was it running before or not, something change, or was it like this from day one ?

    the more you tell, the more we can help

    .

    Comment


      #3
      Yes. If you found anything in the fuel bowls at all, then a complete rebuild is in order. Ed (Nessism) wrote a tutorial on the process. He has a link in his signature and Cliff has one on his web page. Main ingredients include Berryman's carb dip, a set of o-rings from cycleorings.com, and a set of fuel bowl gaskets. Assorted tools, a six pack of your favorite carbonated beverage, etc. helps as well.

      Comment


        #4
        Do you have airbox or pods installed?

        .
        sigpic
        mine: 2000 Honda GoldWing GL1500SE and 1980 GS850G'K' "Junior"
        hers: 1982 GS850GL - "Angel" and 1969 Suzuki T250 Scrambler
        #1 son: 1986 Yamaha Venture Royale 1300 and 1982 GS650GL "Rat Bagger"
        #2 son: 1980 GS1000G
        Family Portrait
        Siblings and Spouses
        Mom's first ride
        Want a copy of my valve adjust spreadsheet for your 2-valve per cylinder engine? Send me an e-mail request (not a PM)
        (Click on my username in the upper-left corner for e-mail info.)

        Comment


          #5
          Are the slides lifting in the carbs ?

          Comment


            #6
            Originally posted by koolaid_kid View Post
            Yes. If you found anything in the fuel bowls at all, then a complete rebuild is in order. Ed (Nessism) wrote a tutorial on the process. He has a link in his signature and Cliff has one on his web page. Main ingredients include Berryman's carb dip, a set of o-rings from cycleorings.com, and a set of fuel bowl gaskets. Assorted tools, a six pack of your favorite carbonated beverage, etc. helps as well.

            U must have read my other post.

            Yes I did find junk in the bowls. I will have to do a tear down rebuild.


            I just found a page on 4 stroke card tuning which was very easy to read.

            So what I understood was there are 3 jets. Idle - Mid - high.
            And to know when to switch jets is when your adjustment screw is ether 2 turns or 1 turn. 2 switch higher 1 switch lower.

            SO I have a 1981 GS1100E 16valves with pods and a 4 in one.

            Before jetting should I start with the Air intake tuning?


            My goal is to get her going so I can ride her a bit. After that I will iron out her kinks.

            Comment


              #7
              Yes, I did read the other post, just thought I would bring it up here, since apparently some others did not read it.
              The first thing to do is the carb rebuild. When you start tearing everything apart, check the jets. With those mods a jet kit is pretty much required and may already be installed. I have been pleased with my DynoJet Stage 3 kit, but others are available.
              Ed's tutorial will walk you through everything. There is also a jetting using plug chops on Cliff's site. I used this one: Jetting CV Carbs
              You are mostly correct, there are 3 stages. First you dial in the main, then the needle height, then the pilot jet. The fuel bowl height can also aid in fine tuning the pilot.
              When to change the pilot is debatable. As long as the air mixture screw can dial you in, I am not sure why you would want to change it. While it is much easier with pods, it is still a pain to swap them out.

              Comment


                #8
                The previous owner bought a DynoJet kit but I do not know which one.
                I will remove the carb tonight. Look at the jets and post back the markings / part numbers I see.

                Can you tell my how junk got in the fuel bowl? Did it come from petcock?
                When in the prime position is it a free flow or does it still get filtered?

                I also would like to know which rebuild kit I should get. Minus the Jets since I might already have the correct ones and if not I will order the DynoJet stage 3.

                Comment


                  #9
                  if your petcock does not have the screen or a damaged one, junk will get into the bowls, probably stuff from the inside of the tank.

                  if your petcock has the filter and in good shape it don't matter what position it's in, it will get filtered first.

                  no rebuild kits, just get all the O rings from www.cycleorings.com and get new bowl gaskets if need be, get the intake O rings as well at cycleorings, take apart the carbs, dip for 24 hours clean out all the jets, unless your getting new ones, and put it all back together.....

                  that's it

                  Comment


                    #10
                    Awh man! I will have to empty my gas tank again and take a look at the petcock.
                    Will I need to get a new petcock gasket?

                    Comment


                      #11
                      Hi,

                      How many of the following have been properly addressed?

                      These are some edited quotes from one of our dear beloved gurus, Mr. bwringer, with ideas on basic needs (depending on initial condition), parts, and accessories.

                      ***********Quoted from Mr. bwringer************

                      Every GS850 [and most other models] has (or had) a set of well-known issues that MUST be addressed before you have a solid baseline for further troubleshooting. It's a vintage bike, and it's quite common (as in, every single GS850 I have had contact with) that there are multiple problems that have crept up and slowly gotten worse over the years. It's not like a newer vehicle, where there's generally one problem at a time.

                      These common issues are:

                      1. Intake O-rings (install NEW OEM or Viton only - common nitrile O-rings will quickly deteriorate from heat)
                      2. Intake Boots (install NEW -- these cannot be repaired)
                      3. Valve clearances (more important than most people think)
                      4. Carb/airbox boots
                      5. Airbox sealing
                      6. Air filter sealing
                      7. Petcock (install a NEW one)
                      8. On '79 models, install new points or Dyna electronic ignition (or at least verify that the old points are working correctly)
                      9. On all models, it's fairly common to have problems with the spark plug caps. These are $3 or $4 each, and often worth replacing if you're keeping the stock coils/wires.
                      10. Stock exhaust with NO leaks or holes -- good seals at the head and at the junctions underneath.


                      What I have noticed at the rallies is that very, very few 850Gs are actually running right. Make VERY sure it's actually running the way it's supposed to before busting out the modifications.


                      Brian's E-Z and fun plan for GS850 happiness:

                      1) Seal the airbox and air filter with weatherstripping.

                      2) Ensure no intake leaks. Spraying WD-40 or water doesn't tell you much, since very small air leaks can cause problems even though they won't suck in enough WD-40 to make a difference. Replace your intake boot o-rings and boots if needed, and seriously consider spending the lousy $28 for new airbox/carb boots.

                      3) Ensure clean carbs with correct settings, new o-rings, and original OEM jets. No, not just squirted with something. I mean completely disassembled.

                      4) Check/adjust valve clearances (Manual calls for every 4,000 miles. This is not optional.)

                      5) Ensure healthy electrical system.

                      6) Seriously consider upgrading coils and plug wires.

                      7) Install new, stock NGK B8-ES plugs gapped to .031".

                      8 ) Fine-tune float height and idle mixture screw to ensure best off-idle transition.

                      9) Clean air filter and reinstall with only the lightest oil mist -- over-oiling and/or letting the filter get dirty is a common and critical mistake, and will make the bike run funny at low speeds and run rich. This may take a few tries.

                      10) Make sure the exhaust seals are sealing.

                      11) Ooh, much better now, huh? You're gonna need upgraded suspension - Progressive or better fork springs and shocks. Set suspension sag appropriately.

                      12) Upgrade brakes with new pads and stainless lines to deal with all that extra speed.

                      13) Install new petcock, since I'm going to head to the roof with a rifle if I have to read about yet another #2 plug fouling and failed hillbilly attempts to rebuild the petcock and/or deny there's a problem.

                      14) Oh yeah -- check compression somewhere in there to ensure the valves and rings are reasonably healthy.

                      15) You'll probably need new OEM clutch springs -- the clutches last forever, but the springs get tired after 20 years or so under pressure. E-Z and cheap.
                      ***************End Quote****************

                      You will find most of the procedures documented on my little website.

                      And don't forget...
                      New Members, CLICK HERE!!

                      Thank you for your indulgence,

                      BassCliff

                      Comment


                        #12
                        BassCliff I'm organizing my self, mostly digesting all the things I need to know befor I do anything. Parts to order, tools to get.

                        I read your other post. I had forgot about those lists.

                        I'm reading "Top 10 Newbie Mistakes" because I do not want to be a noob for long

                        TO answer your question "How many of the following have been properly addressed?" None yet.
                        Last edited by Guest; 08-01-2012, 12:33 AM.

                        Comment


                          #13
                          It's a lot to get your head wrapped around, but the sooner you establish your baseline of maintenance the better. I'll bet most of your issues will disappear just completing the list. For instance, you can try to fix a bad idle or poor acceleration issues all day long and never get it right if the valves are out of adjustment or one single o-ring is bad in the carbs. Good luck!

                          Comment


                            #14
                            I know the previous owner rebuilt the carbs but I can not be 100% sure he did a perfect job.

                            Should I do a complete tear down and rebuild to be 100% sure it's done the proper way?

                            Besides if junk was found in the bows who knows what has been blocked and I will get to learn about the carb internals and be able to picture mentally what's happening in there.

                            I thin I just answered my own question...
                            Last edited by Guest; 08-01-2012, 12:46 PM.

                            Comment


                              #15
                              The GS1100 engine will idle pretty well with only two cylinders running (amazing!), it only needs to have the idle screw give it enough throttle to keep it idling. However, the engine won't spin up if the pilot jets on one or more carbs are clogged, and this is very likely.

                              You do have the pod air filters installed, correct? If they are the oil type, take a rag and blot out as much oil as you can or remove them and see if that helps.

                              Comment

                              Working...
                              X