Announcement

Collapse
No announcement yet.

GS750/1000 Carb Swap

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    GS750/1000 Carb Swap

    My GS 750 is now fitted with Wiseco pistons taking capacity up to 810cc. Had big problems getting the carb settings right and have got it running but still not perfect. After much messing about with jets etc I think that the carb chokes may be too small for the increase in capacity so thinking of fitting either GS850 or 1000 carbs. Does anyone one know if the centre spacing of the inlet ports for these engines is the same as the 750 ie would the carbs from the larger engines simply bolt on? If so does anyone have any ideas on jet sizes as a starting point? Thanks. Rob

    #2
    The early 750/850/1000 all used the same carbs, although the jetting was slightly different.
    Ed

    To measure is to know.

    Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

    Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

    Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

    KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

    Comment


      #3
      Rob,

      I believe your theory about the carbs being too small is blown up by the same carbs being used on much larger bikes.

      I'm assuming this is an older (pre 80) 750 with VM carbs?

      Rejetting can be a pain, an art and a science

      Why don't you tell us more about what problems you are having?
      1978 GS 1000 (since new)
      1979 GS 1000 (The Fridge, superbike replica project)
      1978 GS 1000 (parts)
      1981 GS 850 (anyone want a project?)
      1981 GPZ 550 (backroad screamer)
      1970 450 Mk IIID (THUMP!)
      2007 DRz 400S
      1999 ATK 490ES
      1994 DR 350SES

      Comment


        #4
        It's not just the jets that differed - the needles and slides weren't all the same. The carb sticky post will reveal all that.

        Are you running with the standard airbox and exhaust?
        79 GS1000S
        79 GS1000S (another one)
        80 GSX750
        80 GS550
        80 CB650 cafe racer
        75 PC50 - the one with OHV and pedals...
        75 TS100 - being ridden (suicidally) by my father

        Comment


          #5
          At least on my 750s and 1000s, the slides were the same, the needles and jets were different. The throttle and choke mechanism was different, but it's easy to swap anyway.

          Between the 850 and 750, they are almost exactly the same, jetting and everything.
          http://img.photobucket.com/albums/v5...tatesMap-1.jpg

          Life is too short to ride an L.

          Comment


            #6
            Originally posted by tkent02 View Post
            At least on my 750s and 1000s, the slides were the same, the needles and jets were different. The throttle and choke mechanism was different, but it's easy to swap anyway.

            Between the 850 and 750, they are almost exactly the same, jetting and everything.
            Depends on the 750 - their carb specs wobbled about quite a bit. Plus the one that can catch people out is the position of the clip on the needle. I think it's position 3 on a 750 and 2 on the 850 (or it might be the other way round, I can't remember for sure). I think that the 750 was at least consistent here but I might be wrong.
            79 GS1000S
            79 GS1000S (another one)
            80 GSX750
            80 GS550
            80 CB650 cafe racer
            75 PC50 - the one with OHV and pedals...
            75 TS100 - being ridden (suicidally) by my father

            Comment


              #7
              Not sure, usually the needles are sized so that position three is the stock setting, but I don't know about all models. Maybe. The early 750s were a little different.
              http://img.photobucket.com/albums/v5...tatesMap-1.jpg

              Life is too short to ride an L.

              Comment


                #8
                The 1977 GS750 carbs differ significantly from the 1978/79 GS750 carbs. The slides are smaller and thinner and the pilot fuel passages appear to be different.

                I picked up a junk rack of '77 carbs and was surprised at how different they are from mine.

                Comment


                  #9
                  Originally posted by Big T View Post
                  Rob,

                  I believe your theory about the carbs being too small is blown up by the same carbs being used on much larger bikes.

                  I'm assuming this is an older (pre 80) 750 with VM carbs?

                  Rejetting can be a pain, an art and a science

                  Why don't you tell us more about what problems you are having?
                  Big T. History is as follows: bike bought as a 1980 unit, in a complete mess. Engine completely rebuilt, carbs u/sonically cleaned (many times!). Carbs set with standard jets, std airbox, 4-2 Jarma exhaust,810 cc conversion/re-bore, float height set to std 22.5mm.. Engine difficult to start, running massively rich. Finaly got it running reasonably well reducing the fuel mix by blocking parts of the pilot fuel system, reducing main jets to 95 and pilots to minimum available size, fitting K&N pod filters, new carb/cylinder inlet stubs and new exhaust gaskets used. No obvious air leaks. Carbs do not flood or overflow. Fuel tank cleaned, fuel tap/cock cleaned and refitted along with in line fuel filter. No sign of debris in the fuel or carb bodies. Carbs are Mikuni VM22.choke mechanism set up as per workshop manual. Now starts reluctantly on choke, quickly runs without choke. Once running motor pulls really well, ticks over OK and seems to run fine but spark plugs still indicate rich running. Also restarts from hot ok. Hence my query as to if another carb type would improve things

                  Comment


                    #10
                    Originally posted by RobNeal4 View Post
                    Big T. History is as follows: bike bought as a 1980 unit, in a complete mess. Engine completely rebuilt, carbs u/sonically cleaned (many times!). Carbs set with standard jets, std airbox, 4-2 Jarma exhaust,810 cc conversion/re-bore, float height set to std 22.5mm.. Engine difficult to start, running massively rich. Finaly got it running reasonably well reducing the fuel mix by blocking parts of the pilot fuel system, reducing main jets to 95 and pilots to minimum available size, fitting K&N pod filters, new carb/cylinder inlet stubs and new exhaust gaskets used. No obvious air leaks. Carbs do not flood or overflow. Fuel tank cleaned, fuel tap/cock cleaned and refitted along with in line fuel filter. No sign of debris in the fuel or carb bodies. Carbs are Mikuni VM22.choke mechanism set up as per workshop manual. Now starts reluctantly on choke, quickly runs without choke. Once running motor pulls really well, ticks over OK and seems to run fine but spark plugs still indicate rich running. Also restarts from hot ok. Hence my query as to if another carb type would improve things
                    Wow. This just makes my head hurt. I'll try to unpack your carb settings though.

                    The 1980 GS750 had CV carbs, so that can't be right. Earlier VM carbs won't fit the 1980 head. Carbs should be Mikuni VM26 or BS32. VM22 are for the GS550. I will assume you have VM26. If you have BS32, ignore everything here, as those new-fangled CV carbs confuse my feeble brain.

                    22.5mm is way too low for float height, so it's no wonder the bike ran massively rich. Surprising that it didn't flood. Stock float height for 78-79 GS750 and the earliest GS850 (which used VM26 carbs) is 24mm. Float height affects the mix in all circuits, so everything else you did seemed to overcompensate a bad float height setting. Such as . . .

                    You blocked part of the pilot system . . . and added pod filters . . . and reduced the main jets???

                    Um, that makes no sense. With pod filters, you have more air, so you need to increase the mains and other jets (once you have a good float height).

                    Not sure what effects that aftermarket 4-2 pipe has. Is it freer flowing than the stock 4-2? Akin to the 4-1 pipes? If so, then you should approach the jetting like the typical pods/pipe crowd (we aren't all clowns ).

                    Those specs are close but not identical. You will find them here.

                    The stock jetting for the VM26 carbs for a 750/850 are:

                    Main 100/102.5
                    Pilot 15/15
                    Stock needle setting was either 3d or 2d from top.

                    With pods and a more open pipe, you need to add fuel to the mixture. You might be able to get the pilot right with stock 15s and some adjustment to the screws, but pick up some 17.5 pilots in case you run out of adjustment range.

                    You needle will need to go up (richer). Start with it in the 4th slot down. You may need to shim it more, but I doubt you'll end up in the 5th slot.

                    For mains, you will need to go up a few sizes from stock. Start with jets in the 117.5 range (so grab some 115, 117.5, 120 and maybe 122.5). Be prepared to swap up or down.

                    Before you begin the jetting saga, strip and dip the carbs and put in fresh o-rings for the screws, choke assemblies, etc. Rob Barr has a complete set for you. Also, clean and re-oil (lightly) those K&N pods. If you got the bike to run at all with those jets, I wager those pods are smothered in oil.

                    Bored out to 810, I suspect your jetting baseline is in the same neighborhood as my 750/850. For reference, after LOTS of trial-and-error (mostly error ), I am reasonably pleased with my jetting, as follows:

                    Pilot 17.5
                    Fuel Screw - 7/8 to 1 turn out
                    Air Screw - 2 turns out
                    Needle - 4th slot + 4 #3 washers for a tiny shim.
                    Mains - 117.5

                    The only part I am not certain about in my jetting is the mains, because city riding does not put me in WoT enough to be sure.

                    Comment


                      #11
                      BikeCliff website







                      All links I have found on various threads on the GS resources.
                      A lot more where they came from, these are some I saved.

                      I hope this will not confuse you with the great input by mrcinders.

                      Chart might help you identify carbs better as was a change between
                      77-79 vm26ss and 80-81 bs32ss carbs I don't know what you have.
                      Id # in chart to compare with what is stamped on carb body and the carbs will look different.

                      Hope chart and the links help.

                      Comment


                        #12
                        Wow! Thanks so much for all the advice and the time you've taken over this. Much appreciated. Even though the weather is getting colder now here in the UK I'll be in the garage soon to try out the suggestions.
                        Kind regards.
                        Rob

                        Comment


                          #13
                          Really useful chart. A bit of a strain on an older set of eyes but damn useful, thanks.

                          Regards

                          Rob

                          Comment


                            #14
                            I forget who posted that I am 41 with 20/20 and it is still small. Its a JPEG so you should be able to resize in any paint-photo editing software.

                            Just lets you know what was in as stock.

                            Have read that when changing to pods will need to re-jet and the chart will not help you.

                            That is where the advice from people like mistercinders who has converted comes into play.

                            Here is some more info gleaned from this site about jets.

                            Keihin, Dynojet, Mikuni Jet Size Cross Reference

                            All Hole Diameters Are in Inches

                            Hole Dia”---Keihin # -- DynoJet # -- Mikuni #
                            0.0350---- 92.5--------- 92----------- 86.3
                            0.0360---- 95----------- 94----------- 88.1
                            0.0370---- 97.5--------- 96----------- 90
                            0.0380---- 100---------- 98----------- 91.9
                            0.0390---- 102.5------- 100---------- 93.8
                            0.0400---- 105--------- 102---------- 95.6
                            0.0410---- 107.5------- 104---------- 97.5
                            0.0420---- 110--------- 106---------- 99.4
                            0.0430---- 112.5------- 108--------- 101.3
                            0.0440---- 115--------- 110--------- 103.1
                            0.0450---- 117.5------- 112--------- 105
                            0.0460---- 120--------- 114--------- 106.9
                            0.0470---- 122.5------- 116--------- 108.8
                            0.0480---- 125--------- 118--------- 110.6
                            0.0490---- 127.5------- 120--------- 112.5
                            0.0500---- 130--------- 122--------- 114.4
                            0.0510---- 132.5------- 124--------- 116.3
                            0.0520---- 135--------- 126--------- 118.1
                            0.0530---- 137.5------- 128--------- 120
                            0.0540---- 140--------- 130--------- 121.9
                            0.0550---- 142.5------- 132--------- 123.8
                            0.0560---- 145--------- 134--------- 125.6
                            0.0570---- 147.5------- 136--------- 127.5
                            0.0580---- 150--------- 138--------- 129.4
                            0.0590---- 152.5------- 140--------- 131.3
                            0.0600---- 155--------- 142--------- 133.1
                            0.0610---- 157.5------- 144--------- 135
                            0.0620---- 160--------- 146--------- 136.9
                            0.0630---- 162.5------- 148--------- 138.8
                            0.0640---- 165--------- 150--------- 140.6
                            0.0650---- 167.5------- 152--------- 142.5
                            0.0660---- 170--------- 154--------- 144.4
                            0.0670---- 172.5------- 156--------- 146.3
                            0.0680---- 175--------- 158--------- 148.1
                            0.0690---- 177.5------- 160--------- 150
                            0.0700---- 180--------- 162--------- 151.9
                            0.0710---- 182.5------- 164--------- 153.8
                            0.0720---- 185--------- 166--------- 155.6
                            0.0730---- 187.5------- 168--------- 1575
                            0.0740---- 190--------- 170--------- 159.4
                            0.0750---- 192.5------- 172--------- 161.3
                            0.0760---- 195--------- 174--------- 163.1
                            0.0770---- 197.5------- 176--------- 165
                            0.0780---- 200--------- 178--------- 166.9
                            0.0790---- 202.5------- 180--------- 168.8
                            0.0800---- 205--------- 182--------- 170.6
                            0.0810---- 207.5------- 184--------- 172.5
                            0.0820---- 210--------- 186--------- 174.4
                            0.0830---- 212.5------- 188--------- 176.3
                            0.0840---- 215--------- 190--------- 178.1
                            0.0850---- 217.5------- 192--------- 180
                            0.0860---- 220--------- 194--------- 181.9
                            0.0870---- 222.5------- 196--------- 183.7
                            0.0880---- 225--------- 198--------- 185.6
                            0.0890---- 227.5------- 200--------- 187.5

                            Comment


                              #15
                              Originally posted by Crankthat View Post
                              I forget who posted that I am 41 with 20/20 and it is still small. Its a JPEG so you should be able to resize in any paint-photo editing software.

                              Just lets you know what was in as stock.

                              Have read that when changing to pods will need to re-jet and the chart will not help you.

                              That is where the advice from people like mistercinders who has converted comes into play.
                              Yes, the chart just shows the stock jetting. Since few if any of us are the original owners of these bikes, the chart helps figure out what "par" is when tearing down the carbs and discovering what some PO did to them over the decades. Typical PO sins include:

                              - mixing pilot jet sizes
                              - changing the main jets in an attempt to sort out all manner of mixture issues (e.g., "it won't idle well. Guess I better go up 7 sizes on the mains")
                              - blindly replacing OEM jets (mains, pilots, screws) with rebuild kit parts ("so shiny, must be better than those grimy old jets").

                              To address the changes needed for pods/pipes, the chart at least tells you where to find par, even if you cannot return the bike to stock and get it running there before modding the fuel/air system (which is the best approach).

                              Comment

                              Working...
                              X