Announcement

Collapse
No announcement yet.

Header holes/ what can be done?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Header holes/ what can be done?

    Question, The headers I'm using on my G have developed holes at the underside of two down tubes. This is temporary exhaust for this bike, bv I do want to use it as long as I can for exhaust on projects. I'm looking for option for temporary and long term fixes. Options I can think of, but have never tried are exhaust tape(the silver stuff you can wrap around car ex.), heat wrap commonly user on drag car headers and popular with cafe and bobber bikes, J-BWeld. Has anyone tried any of these with positive results? I'll post a photo of the holes later.
    :cool:GSRick
    No God, no peace. Know God, know peace.

    Eric Bang RIP 9/5/2018
    Have some bikes ready for us when we meet up.

    #2
    The only solution is to weld a patch over the hole

    Comment


      #3
      To temporarily repair an exhaust leak on a diesel tractor, I used a piece of heavy-duty aluminum foil, folded several times to form a square, then held in place with a stainless pipe clamp. Worked great and is still in place some years later.
      1982 GS1100GL Citrus County, FL

      a rare outsider and was only built until 1983. Who still has one, it gives her so little.

      Comment


        #4
        Originally posted by SqDancerLynn1 View Post
        The only solution is to weld a patch over the hole
        That will be the plan eventually, but I fear since the tubing is thin (the reason for the holes in the first place) more holes will be the result, atleast it will if I try to do it. lol I need a temporary bandaid for the short term. This is my, backup/work in progress bike, thrust into duty unexpectantly.
        Last edited by gsrick; 03-25-2013, 06:04 PM.
        :cool:GSRick
        No God, no peace. Know God, know peace.

        Eric Bang RIP 9/5/2018
        Have some bikes ready for us when we meet up.

        Comment


          #5
          J-B Weld, the duct tape of epoxies!
          sigpicSome of the totally committed probably should be.
          '58 + '63 Vespa 150's' (London, GB/RI, US)
          '67 X6 T20 ('67 Long Beach, Ca.- misty-eyed)
          '71 Kaw. A1-ugh ('71 SF, CA- worked @ Kaw dlr)
          '66 Yam. YL1('72 SF-commuter beater)
          '73 Kaw. S2A-2Xugh ('73 SF-still parts slave)
          '78 GS 750C ('77 SF-old faithful-killed by son)
          '81 KZ 750E ('81 SF-back to Kaw. dlr)
          '81 GS 650G ('08 back to NE&ME- (project)
          '82 GS '82 (2) GS650GZ, L, Middlebury, G current

          Comment


            #6
            Small holes? For a temporary bodge try a hose clip.
            79 GS1000S
            79 GS1000S (another one)
            80 GSX750
            80 GS550
            80 CB650 cafe racer
            75 PC50 - the one with OHV and pedals...
            75 TS100 - being ridden (suicidally) by my father

            Comment


              #7
              If the holes are really small I wouldn't worry too much about it, you need a place for water to escape .

              Somekind of tape wrap should work along with a little epoxy, Jb weld etc,
              how about that aluminum "real" duct tape?
              sigpic
              Steve
              "The world is a book, and those who do not travel read only one page." :cool:
              _________________
              '79 GS1000EN
              '82 GS1100EZ

              Comment


                #8
                Originally posted by sedelen View Post
                If the holes are really small I wouldn't worry too much about it, you need a place for water to escape .

                Somekind of tape wrap should work along with a little epoxy, Jb weld etc,
                how about that aluminum "real" duct tape?
                Hey Steve, I picked up some exhaust tape. It's a foil with an adhesive backing. Well I'll see how well it holds up. It worked in the garage, but I haven't tested it out going on a ride.
                Here are the holes in question, I found a few more after covering these.

                Here is the product I'm trying. $3.99 at AutoZone.
                :cool:GSRick
                No God, no peace. Know God, know peace.

                Eric Bang RIP 9/5/2018
                Have some bikes ready for us when we meet up.

                Comment


                  #9
                  It's worked so far, but my ride to work is very short.
                  :cool:GSRick
                  No God, no peace. Know God, know peace.

                  Eric Bang RIP 9/5/2018
                  Have some bikes ready for us when we meet up.

                  Comment


                    #10
                    Originally posted by gsrick View Post
                    Hey Steve, I picked up some exhaust tape. It's a foil with an adhesive backing. Well I'll see how well it holds up. It worked in the garage, but I haven't tested it out going on a ride.
                    Here are the holes in question, I found a few more after covering these.

                    Here is the product I'm trying. $3.99 at AutoZone.
                    Hope you plan on replacing those soon!
                    Looks to be paper thin.
                    sigpic
                    Steve
                    "The world is a book, and those who do not travel read only one page." :cool:
                    _________________
                    '79 GS1000EN
                    '82 GS1100EZ

                    Comment

                    Working...
                    X