Announcement

Collapse
No announcement yet.

Carburetor Adjusting Tool

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
    #1

    Carburetor Adjusting Tool

    Hi need help , looking for a Carburetor Adjusting Tool , i just got one from motion pro, and it will not even come cloes to working, dose anyone know of one that wil work, to adjust the fuel screw on a 79 gs1000 with vm carbs i made 2 colortunes and can use then lol

    thanks Bill.
    Tags: None
    #2
    AHHHH...whats the problem with it?
    MY BIKES..1977 GS 750 B, 1978 GS 1000 C (X2)
    1978 GS 1000 E, 1979 GS 1000 S, 1973 Yamaha TX 750, 1977 Kawasaki KZ 650B1, 1975 Honda GL1000 Goldwing, 1983 CB 650SC Nighthawk, 1972 Honda CB 350K4, 74 Honda CB550

    NEVER SNEAK UP ON A SLEEPING DOG..NOT EVEN YOUR OWN.


    I would rather trust my bike to a "QUACK" that KNOWS how to fix it rather than a book worm that THINKS HE KNOWS how to fix it.

    Comment

      #3
      the Blade part is too big !!!! so you would need to grind on it a little..

      Comment

        #4
        If the bits are too short, take a cheap screwdriver and saw the shank off. Grind it to fit and go to it.
        MY BIKES..1977 GS 750 B, 1978 GS 1000 C (X2)
        1978 GS 1000 E, 1979 GS 1000 S, 1973 Yamaha TX 750, 1977 Kawasaki KZ 650B1, 1975 Honda GL1000 Goldwing, 1983 CB 650SC Nighthawk, 1972 Honda CB 350K4, 74 Honda CB550

        NEVER SNEAK UP ON A SLEEPING DOG..NOT EVEN YOUR OWN.


        I would rather trust my bike to a "QUACK" that KNOWS how to fix it rather than a book worm that THINKS HE KNOWS how to fix it.

        Comment

          #5
          The bit is part of the tool... or widen the slot in the needle

          Comment

            #6
            Lynn..ive seen some 90 degree carb tools that have 4 sizes of bits ,,two slotted and 2 phillips that slip in like a socket kinda holder deal. Thats why i stated what i did.
            MY BIKES..1977 GS 750 B, 1978 GS 1000 C (X2)
            1978 GS 1000 E, 1979 GS 1000 S, 1973 Yamaha TX 750, 1977 Kawasaki KZ 650B1, 1975 Honda GL1000 Goldwing, 1983 CB 650SC Nighthawk, 1972 Honda CB 350K4, 74 Honda CB550

            NEVER SNEAK UP ON A SLEEPING DOG..NOT EVEN YOUR OWN.


            I would rather trust my bike to a "QUACK" that KNOWS how to fix it rather than a book worm that THINKS HE KNOWS how to fix it.

            Comment

              #7
              no it will not even get in to it , the bit fits but will not reach it,

              Comment

                #8
                get creative and make something work..its what i would do.
                MY BIKES..1977 GS 750 B, 1978 GS 1000 C (X2)
                1978 GS 1000 E, 1979 GS 1000 S, 1973 Yamaha TX 750, 1977 Kawasaki KZ 650B1, 1975 Honda GL1000 Goldwing, 1983 CB 650SC Nighthawk, 1972 Honda CB 350K4, 74 Honda CB550

                NEVER SNEAK UP ON A SLEEPING DOG..NOT EVEN YOUR OWN.


                I would rather trust my bike to a "QUACK" that KNOWS how to fix it rather than a book worm that THINKS HE KNOWS how to fix it.

                Comment

                  #9
                  what is was going to do , just thought someone that has been doing carb adjustments, might know something !

                  Comment

                    #10
                    Ive never had one myself. I took a cheap small flat tip, cut it off and wrapped electrical tape to make a sort of handle around the adjusted shank. reach under and do the dead. Tight hot fit but its doable.
                    MY BIKES..1977 GS 750 B, 1978 GS 1000 C (X2)
                    1978 GS 1000 E, 1979 GS 1000 S, 1973 Yamaha TX 750, 1977 Kawasaki KZ 650B1, 1975 Honda GL1000 Goldwing, 1983 CB 650SC Nighthawk, 1972 Honda CB 350K4, 74 Honda CB550

                    NEVER SNEAK UP ON A SLEEPING DOG..NOT EVEN YOUR OWN.


                    I would rather trust my bike to a "QUACK" that KNOWS how to fix it rather than a book worm that THINKS HE KNOWS how to fix it.

                    Comment

                      #11
                      You need to remove the choke connector housing out of the way and it will get into where it needs to go between two and three. You shouldn't have any issues reaching between the frame tubes on the others.
                      Cowboy Up or Quit. - Run Free Lou and Rest in Peace

                      1981 GS550T - My First
                      1981 GS550L - My Eldest Daughter's - Now Sold
                      2007 GSF1250SA Bandit - My touring bike

                      Sit tall in the saddle Hold your head up high
                      Keep your eyes fixed where the trail meets the sky and live like you ain't afraid to die
                      and don't be scared, just enjoy your ride - Chris Ledoux, "The Ride"

                      Comment

                        #12
                        I tried , the center u turn will not pull out,

                        Comment

                          #13
                          Take a picture please with the tool in position please
                          Cowboy Up or Quit. - Run Free Lou and Rest in Peace

                          1981 GS550T - My First
                          1981 GS550L - My Eldest Daughter's - Now Sold
                          2007 GSF1250SA Bandit - My touring bike

                          Sit tall in the saddle Hold your head up high
                          Keep your eyes fixed where the trail meets the sky and live like you ain't afraid to die
                          and don't be scared, just enjoy your ride - Chris Ledoux, "The Ride"

                          Comment

                          Previous template Next
                          Working...
                          X