Fuel system check: 77 GS750

[hannibal]

I picked up a 1977 GS750 with 23k miles a few weeks ago. I immediately had some electrical issues so I tackled those first by rewiring the positive side, installing a new blade type fuse, and a creating a single grounding point. I plan to add some relays and create 3 separate circuits (ignition, lights, and signals) but before I spend effort on that, I wanted to take a look at the fuel system.

I quickly found my petcock was only working occasionally, and when it wasn't working, it was letting fuel run into the carbs. I've since pulled the tank and removed the petcock, and I'm currently awaiting a new one from Z1 (shipped out today!).

I glanced inside my tank and found rust. I'd say it looks like "day 3" in this pic:

http://www.mopedarmy.com/mediawiki/images/5/54/Five_day_vinegar_tank.jpg

So my plan for this weekend is to try rust removal by electrolysis. I've never done anything like this before but I've read some good links on the subject. I also plan to pull the carbs off and begin cleaning them. I'll also take note of the jet sizes, as the bike came with pods and I have little confidence that it's been jetted correctly. After cleaning, I'll bench sync them. I also have a carb sync tool on the way so I can vacuum sync after reinstalling. I'll also take a look at the boots and O rings. Any other parts of the fuel system need to be looked at? Between the tank, petcock, and carbs, I think I'm covered.

My last goal for the weekend is to change the oil (assuming it's full of fuel; haven't look) and check valve clearances. Again, a very new concept for me (the Nissans I used to work on all had hydraulic adjusters) but I've read many write ups and threads on the subject. So hopefully by Monday I can order any necessary carb parts (jets, O rings, etc) and shims.

I'm taking the MSF riding course in three weeks, after which I'll be able to get a license. My goal is to have the bike up and running with all the basic maintenance items checked off by then. I know there's a lot more to be done, but I want to at least do a compression check and stator and R/R check before putting any more time and effort into this thing.

[tkent02]

I picked up a 1977 GS750 with 23k miles a few weeks ago. I immediately had some electrical issues so I tackled those first by rewiring the positive side, installing a new blade type fuse, and a creating a single grounding point. I plan to add some relays and create 3 separate circuits (ignition, lights, and signals) but before I spend effort on that, I wanted to take a look at the fuel system.

I quickly found my petcock was only working occasionally, and when it wasn't working, it was letting fuel run into the carbs. I've since pulled the tank and removed the petcock, and I'm currently awaiting a new one from Z1 (shipped out today!).

I glanced inside my tank and found rust. I'd say it looks like "day 3" in this pic:

http://www.mopedarmy.com/mediawiki/images/5/54/Five_day_vinegar_tank.jpg

So my plan for this weekend is to try rust removal by electrolysis. I've never done anything like this before but I've read some good links on the subject. I also plan to pull the carbs off and begin cleaning them. I'll also take note of the jet sizes, as the bike came with pods and I have little confidence that it's been jetted correctly. After cleaning, I'll bench sync them. I also have a carb sync tool on the way so I can vacuum sync after reinstalling. I'll also take a look at the boots and O rings. Any other parts of the fuel system need to be looked at? Between the tank, petcock, and carbs, I think I'm covered.

My last goal for the weekend is to change the oil (assuming it's full of fuel; haven't look) and check valve clearances. Again, a very new concept for me (the Nissans I used to work on all had hydraulic adjusters) but I've read many write ups and threads on the subject. So hopefully by Monday I can order any necessary carb parts (jets, O rings, etc) and shims.

I'm taking the MSF riding course in three weeks, after which I'll be able to get a license. My goal is to have the bike up and running with all the basic maintenance items checked off by then. I know there's a lot more to be done, but I want to at least do a compression check and stator and R/R check before putting any more time and effort into this thing.

Sounds like you have the right attitude about maintenance. Wanting to get it all working right first is smart. Electrolysis works, it takes some time and effort but it makes for a clean tank.
As far as the compression test, don't worry about it for now. Tight valves will cause low compression, as will sitting a long time. Adjust the valve clearances, ride it a few thousand miles, then the compression will probably be OK. 23,000 miles isn't enough to wear anything out unless it's really been abused.

Another thing to look at is the cam timing, it only takes a few minutes to check if you have the valve cover off already. I have found a lot of these bikes with one or both cams off by a tooth or even two. It will run, even run OK at certain RPMs, but it won't be right. As a new rider you probably wouldn't notice until you ride one with the cams set properly.

Speaking of timing, your '77 has contact points type ignition. Is it working correctly? Ignition timing correct? They are very reliable but they do take a little time and effort occasionally.

[hannibal]

Will check the cam timing when i do valves. Thanks for the advice. I have not looked at the ignition at all. I don't think I've seen a write up on checking ignition timing, only how to line it up before removing cam chain. I'll certainly search and look over bassclif's site but if you know of a good thread I'd appreciate the link.

I bought this bike to ride not wrench on. I enjoy working on cars and such but didn't intend for this to be project. But this is what i got and if it takes work to make enjoyable, then that's what i gotta do.

[chuck hahn]

Heres the service manual....

http://www.mtsac.edu/~cliff/storage/gs/GS750_Service_Manual_early8valve.pdf

[tkent02]

I bought this bike to ride not wrench on. I enjoy working on cars and such but didn't intend for this to be project. But this is what i got and if it takes work to make enjoyable, then that's what i gotta do.

A ten year old bike would take a lot less work. Still more than a car but a lot less. Cheaper too, faster, all of that.

[chuck hahn]

But just like an old car, youre gonna be doing a lot of fixing the previous owners "fixes" and such..right?? And checking all the parts and doing maintenance..right? So whats different about getting ahold of an old bike? I fail to see why your complaining.

[tkent02]

What Chuck said. Once everything is fixed, a few hours once a year and a few minutes once every few months to change the oil is all it takes.
It's fixing decades of neglect that takes so much time and effort. Which is where the ten year old bike comes in. It can only have ten years of neglect to repair.

[chuck hahn]

Exactly!!!!!!!!!!!!!!!

[hannibal]

As always, thanks for the replies.

What Chuck said. Once everything is fixed, a few hours once a year and a few minutes once every few months to change the oil is all it takes.
It's fixing decades of neglect that takes so much time and effort.

This is the approach I'm taking. The bike was advertised as ready to ride, but I quickly learned it was not. As I said before, this is my starting point and if the bike needs work to be decently reliable, then that's what I'll do.

I got the carbs off the bike this morning, but having trouble getting the mounting plate off. I'm following the guide from bikecliff's site: http://members.dslextreme.com/users/...rb_rebuild.pdf

It says to remove the 8 screws holding the carbs to the mounting plate, them pull the plate off. But the throttle shaft runs through guides on the mounting plate so I can't just pull the plate off. I removed the throttle shaft stopper tab and took off the rubber grommets on the ends of the throttle shaft, but I can't slide the shaft out because the throttle pulley (where the throttle cable attaches) obviously can't fit through the carb bodies. Am I missing something here??


The pic shows the mouthing plate and the throttle shaft guide between carbs 3 and 4.

[hannibal]

Got it. Had to pull the tops of the carb out and remove hex bolt from each carb. Also removed a screw on the throttle pulley and it slides right out.

[nickjtc]

What Chuck said. Once everything is fixed, a few hours once a year and a few minutes once every few months to change the oil is all it takes.It's fixing decades of neglect that takes so much time and effort. Which is where the ten year old bike comes in. It can only have ten years of neglect to repair.

Never truer words spoken! I'm 'fighting' with a bike ridden off the street into a garage and parked for 20+ years. If just a modicum of preventative putting-away maintenance had been done I would not have to have rebuilt/replaced the brake systems, changed the fork seals and replaced the (rotted) air filter. And I haven't even looked at what the inside of the carbs look like!!

It's a labour of love, though.

[hannibal]

So I got most of the carb separated. Had to get a small screwdriver to get the pilot fuel screws out. One of the springs for this screw is stuck in the carb body. I've sprayed some cleaner in there but can't seem to get it out. Any harm in soaking the body with the spring stuck inside? I'm hoping a good soak with loosen it.

I've never opened up a carb before and I'm amazed at how simple, yet complex these things are. I get that the slide acts like a throttle plate, but I'm baffled by the insides of the slide assembly. The bolt on the arm seems to move the slide up and down, like a fine tuning adjustment. I haven't removed the innards of the actual slide yet. Anybody care to explain what's going on in there?

Thank you much!

[chuck hahn]

Small bend in a paperclip to fish the spring out.

[chuck hahn]

The screws on top of the slldes are what you use to bench sync them and what you adjust with the gauges when its running and youre doing the vacuum sync.

Bench syncing is just seeing ( visually from the engine side ) that all the slides are about the same gaps from the bottom of the slides to the rim of the carbs bore. Just touch the idle knob to the throttle linkage and then go in about 1 1/2 turns on the idle knob. Now use the adjuster to set the gap about 20 thousands or so across all 4 slides. This is now a bench synced set of carbs.

When you mount them and are doing the actual final gauge sync, all youre doing is moving each individual slide up or down a tad till all 4 gauges are reading the same vacuum draw across all 4 cylinders. Once all 4 are the same you snug down the jam nut and
pout the covers on.

[chuck hahn]

This is basically what you want to see if they are all balanced right.