WHat wires go where? Ignition coils

[Spanish_ryder]

Hey all I just need some help with wire spots on a gs 750t

where do the 4 wires go that go to the ignition coil? there are 2 orange ones and a black and white one? could some one take a snap shot of there running bike and post it? Or just explain it? both the male plugs on the end of the coils are pointing towards the tail end of the bike. thanks!

[GabrielGoes]

Hey all I just need some help with wire spots on a gs 750t

where do the 4 wires go that go to the ignition coil? there are 2 orange ones and a black and white one? could some one take a snap shot of there running bike and post it? Or just explain it? both the male plugs on the end of the coils are pointing towards the tail end of the bike. thanks!

post some close pictures of what your lookin at... from what you said it seems the 2 orange ones goto power and the black and white ones get grounded?? i dunno i would need pictures everyone here can help you a lot better with pictures

[tom203]

Hey all I just need some help with wire spots on a gs 750t

where do the 4 wires go that go to the ignition coil? there are 2 orange ones and a black and white one? could some one take a snap shot of there running bike and post it? Or just explain it? both the male plugs on the end of the coils are pointing towards the tail end of the bike. thanks!

Best not to jump around in these catagories as it confuses some of us. You had a post in rebuild that is related to this with more info that would help others figure out your problem.
Anyways the orange/ white wires are probably the positive feed from your ignition or kill switch ( if you still have one); the other two wires would either go down to your contact points or your ignitor depending on what you have for an ignition system.

[hikermikem]

Hey all I just need some help with wire spots on a gs 750t

where do the 4 wires go that go to the ignition coil? there are 2 orange ones and a black and white one? could some one take a snap shot of there running bike and post it? Or just explain it? both the male plugs on the end of the coils are pointing towards the tail end of the bike. thanks!

The orange wires are the 12V leads that feed the coils, one wire to each coil (doesn't matter which orange wire goes to which coil).

The white & black wires are the grounds that come from the sig generator/points plate...

The white one goes to the left coil (as sitting on the bike) and that fires plugs 1 & 4. The black (may have a yellow stripe in it) goes to the right coil & fires plugs 2 & 3.

[Spanish_ryder]

OK Thanks Guys will do!

[Spanish_ryder]

is that Right i know its a small picture? how do you post em Huge!?
Thanks

[BassCliff]

is that Right i know its a small picture? how do you post em Huge!?
Thanks

Hi,

There's a guide on my website that shows you how to post pictures here. You'll find other useful information there too. Start with the READ ME page.


Thank you for your indulgence,

BassCliff

[Spanish_ryder]

10 characters

[Spanish_ryder]

heres the pic what the last 2 post were suppose to have lol

[tom203]

Hi,

There's a guide on my website that shows you how to post pictures here. You'll find other useful information there too. Start with the READ ME page.


Thank you for your indulgence,

BassCliff

Sure, now you tell me after three months of playing with that paperclip!

[GabrielGoes]

The orange wires are the 12V leads that feed the coils, one wire to each coil (doesn't matter which orange wire goes to which coil).

The white & black wires are the grounds that come from the sig generator/points plate...

The white one goes to the left coil (as sitting on the bike) and that fires plugs 1 & 4. The black (may have a yellow stripe in it) goes to the right coil & fires plugs 2 & 3.

this was pretty much your answer, do you still ahve any other questions?