Announcement
Collapse
No announcement yet.
Stator cover wiring
Collapse
X
-
Stator cover wiring
Hello out there in Suzuki land I am looking for some input on how to get the 5 phillips screws that hold in the black cable. I have got one out but it seems they are welding in super tight. I am talking the engine covers off to have them polished. I am kinda stuck! Also any input on how to get the shifter cable off to get the square cover off beside the stator cover. I have checked my service manual but no real info on how to. Thanks for any help I really appreciate it. Sincerely BrianTags: None
-
little $20 Impact driver kit is a must when working on bikes. also those aren't phillips heads, actually JIS slightly different but available from ebay. Phillips will work when used with the impact driver, but JIS is better... Good luck, and what bike are you working on???1983 GS1100E, 1983 CB1100F, 1991 GSX1100G, 1996 Kaw. ZL600 Eliminator, 1999 Bandit 1200S, 2005 Bandit 1200S, 2000 Kaw. ZRX 1100
-
If the screws are super tight, all Philips will do is muller the heads. Get the proper JIS impact driver bit for them.
Also, when attempting to get them out, apply some concentrated localised heat on where the screws go into the casing - the raised long lumps on the engine side of the case. I use a small butane torch for this, the type that is commonly sold as a chef's crisping torch.
https://www.amazon.co.uk/MasterClass...dp/B00TFOZLFG/
They're available much cheaper than that, that's just an illustration. Since getting them, I've lost count of the number of casing screws, brake caliper bolts, etc, that I'd been able to get out with no drama or risk of shearing the bolt.Last edited by Grimly; 11-12-2022, 11:13 PM.---- Dave
Only a dog knows why a motorcyclist sticks his head out of a car window
Comment
-
the wires from stator eventually have connectors you can unplug. Follow them . You'll eventually come to a spot near the component that is the voltage /rectifier/regulator (the "R/R")
Then you can put the cover on the bench.
I don't have Harbor Freight here (We have "Princess Auto") but I think from limited experience with a couple that most cheapo impact drivers DO have useable bits for bikes. Though they might shatter in hard use. But a 'Vessel" brand is a better bet.
Comment
-
Thanks so much guys--I think I will try tracing the wires and un connect them so I can get on the bench. One more thing I took my nut off my gearshift lever so I could try and get the cover off. It is not wanting to come off the spline, I am trying to be careful not to mar. Any suggestions on that?? Brian
Comment
-
Forum GuruPast Site Supporter
Super Site Supporter- Jun 2018
- 5539
- Mifflinburg, PA / Land of Tar & Chip
After the stator cover screws are removed and the shift lever is out of the way, the stator cover will fight you because the magnets in rotor are pulling on the stator. Resist the temptation to use any metal prying tools. A few taps around the cover with a wooden handle of any sort or a rubber mallet may be needed to break the gasket seal. It will come.Rich
1982 GS 750TZ
2015 Triumph Tiger 1200
BikeCliff's / Charging System Sorted / Posting Pics
Destroy-Rebuild 750T/ Destroy-Rebuild part deux
Comment
-
Forum GuruPast Site Supporter
Super Site Supporter- Jun 2018
- 5539
- Mifflinburg, PA / Land of Tar & Chip
Yes, once the screw is removed, the shift lever comes straight off. Crud will fight you. For better or worse, I would likely shoot it with brake cleaner then a little WD40 or PB blaster to help. Then again, I ride in a lot of dirt so things down low get cruddy. You could pry a little with a flat head screwdriver in the gap where the screw came out. Just a little. Not sure about your bike, but on mine, the lever has to come off because the shift shaft goes through the stator cover.Rich
1982 GS 750TZ
2015 Triumph Tiger 1200
BikeCliff's / Charging System Sorted / Posting Pics
Destroy-Rebuild 750T/ Destroy-Rebuild part deux
Comment
-
Forum GuruPast Site Supporter
Super Site Supporter- Jun 2018
- 5539
- Mifflinburg, PA / Land of Tar & Chip
Once you remove the stator cover there could be a big washer (different engine, YMMV) on the end of the starter motor idler gear shaft. It will want to disappear. Don’t let it. You need it. If, you have one. I really don’t know.Rich
1982 GS 750TZ
2015 Triumph Tiger 1200
BikeCliff's / Charging System Sorted / Posting Pics
Destroy-Rebuild 750T/ Destroy-Rebuild part deux
Comment
-
Something I found out that I wasn't expecting when I replaced the stator on my 1000S, was the power of that magnet when you start to position the cover to bolt it back on..be prepared and have a good grip on it because it will suck the cover right out of your hands causing that very thin washer to then disappear into the magnet somewhere. Danger Will Robinson! I found it but it took awhile.1979 GS1000S,
1982 Honda CX500 Turbo, 1982 Honda MB5 w/CR80 motor, 1977 Honda "nekid" Goldwing, 1976 Honda CB550F cafe', 1972 Honda XL250 cafe'
Comment
Comment