Announcement

Collapse
No announcement yet.

Top 10 Newbie Mistakes

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Top 10 Newbie Mistakes

    1A) (NEW) Trying to diagnose running problems on a bike with an unknown maintenance history. Common maintenance items like clean carbs, properly adjusted valves, no air leaks in the intake system (airbox, carb boots), a clean gas tank (no rust), and a properly functioning petcock are 100% mandatory for the bike to run properly. It's best to perform all the bikes maintenance when you first get the bike, and then if problems show up you will know what the problem is not.

    1B) Incomplete carb cleaning. A proper carb cleaning requires a full tear down, soaking the parts in carb dip or ultrasonic, and reassembly with fresh O-rings. Pilot jets, choke tubes, and pilot circuit passages in particular need a proper cleaning before the bike will run right. Even if the bike seems to run right, if the O-rings are original they are sure to be hard and brittle thus problems could be right around the corner. This is a link to a carb tutorial that you may find useful... https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

    1C) Purchasing aftermarket parts when OEM Suzuki parts are still available. Check out places like partsoutlaw.com and partzilla.com (or cmsnl.com for the European audience) for availability of OEM parts before ordering often inferior aftermarket parts off ebay or similar. This is particularly true for things like brake master cylinder & caliper rebuild kits. Also, gaskets. OEM Suzuki gaskets are the best (never buy green gaskets.) You can get the OEM part number from these sources and then search ebay for a lower price too.

    2) Not replacing the intake boot O-rings. The classic "hanging idle" (or idle speed that increases on it's own as the bike warms up) is often traced to this simple fix since air gets sucked past the old O-rings and into the engine causing a lean condition. All GS bikes, other than the 2nd generation 750 or 1100E family, use these O-rings. While you are at it, make sure the entire airbox system is 100% sealed since drawing false air into the system will increase running temperatures and make the bike run poorly. Oh, and spraying stuff on the carb boots and looking for a change in the idle doesn't not always show airleaks.

    3) Not adjusting the valves. The valves tighten with mileage and once all the clearance is gone the valves hang open and burn. Not good. If you wait for your bike to misbehave before performing this critical maintenance you may damage the engine. If your valves have no clearance you will need a thin "checking shim" in order to achieve some clearance and then calculate the needed shims for your engine.

    4) Trying to run the bike without the airbox...or installing pods w/o rejetting. The air/fuel ratio will be drastically lean, which will not only cause running problems, but likely damage the engine by causing it to run hot. Installing a free flowing exhaust will likewise change the jetting requirements, but not as drastically as pods. If you have your heart set on running pods, buy good quality K&N, UNI, APE or similar. Steer clear of cheap china pods like Emgo, and the like. Some of these block airflow into the carb passages, and they are just plain low quality pieces. Do better... Lastly, member zed1015 sells air correction jets that are the cheat code to getting your jetting correct when using pods. Hit him up and save yourself a lot of trial and error...https://www.thegsresources.com/_foru.../49974-zed1015

    5) Ordering "carb kits" full of inferior aftermarket jets. A new O-ring kit (https://www.thegsresources.com/_foru...ts#post1703182) is all that's necessary most of the time. Get some new float bowl gaskets and pilot jet plugs if necessary from a place like Z1 Enterprises to supplement the O-ring kit. Also consider replacing the float needles/seats using real deal Mikuni (or Keyster) parts if the float needle spring won't hold up the weight of the float and/or if there is a wear mark on the needle.

    5b) (courtesy of bwringer) Trying to repair or rebuild a leaking or nonfunctional petcock. The odds of any success are vanishingly low. Replace it and worry about something else for the next 30 years. This is a valve that controls the flow of a incredibly flammable, highly explosive substance a few inches from your crotch. Even if rebuild kits worked more than rarely, it's really not worth messing around.

    6) Trying to clean out the brake system full of brown gunky fluid by flushing the system. If the fluid is dark and brown the only way to clean the system is a full tear down and clean out otherwise chunks will remain behind in the system. While you're at it, the old rubber brake lines should be changed. Suzuki call for replacing the lines every 2 years, so if your bike still has the originals, you are decades overdue. The old lines will lead to spongy brake lever feel and contaminate the fresh fluid you just installed.

    7) Waiting for the charging system to fail, instead of cleaning up the old wiring. Many a battery have been boiled dry after the grounds corrode. Running a dedicated ground to the battery, or a solid frame attachment point, is strongly advised. Suzuki also botched the stator wiring by routing one leg up to the now discontinued head lamp switch. This needless wire path often overheats and damages the harness in the process. Do yourself a favor and rewire your charging system: see this thread for guidance. And if you need a new R/R, a SERIES type is the best because it protects your stator from return current overheat damage. The SH775 is a series R/R made by Shindengen that was installed on various bikes, so they are reasonably easy to find on ebay. They are reliable units, so no worry with purchasing used.

    8) Using the wrong oil and/or gasoline. Auto oils have less zinc and phosphorus (high pressure additives) than they used to since the EPA has mandated reductions to protect catalytic converters. Motorcycle oils are fine but expensive, and even motorcycle oil has reduced additives these days. Diesel engine oil is cheap and contains lots of high pressure additives appropriate for our engines. Shell Rotella oil is even certified for use with wet clutches if that makes you more comfortable, although just about any diesel oil is fine. As for fuel, Suzuki calls for use of Regular gas. Using Premium provides no positive benefits for your bike and is more expensive.

    9) Search out the information about your upcoming wrenching tasks before going off unprepared and possibly damaging something. Search using "Advanced Search" and then click "Titles Only" to quickly hone in on the topic at hand. Almost every possible question a newbie could ask have already been answered. For example: there are tons of threads on how to avoid broken exhaust bolts and float posts. Sadly, most newbies learn these tricks AFTER they damage their bike.

    10) Buying a 30+ year old motorcycle because it was cheap, without any mechanical knowledge and no interest in learning. Paying a shop to work on your old motorcycle is not advised unless you have lots of money to spend and know for a fact that they are trustworthy.




    .
    Last edited by Nessism; 05-17-2024, 12:10 PM.
    Ed

    To measure is to know.

    Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

    Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

    Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

    KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

    #2
    11) Pay way too much for some neglected old junker, spending a few months and paychecks learning how to work on a few simple old mechanical things and then trying to get the "investment" back by selling it on to some other unknowing sap.
    http://img.photobucket.com/albums/v5...tatesMap-1.jpg

    Life is too short to ride an L.

    Comment


      #3


      That needs to be made a STICKY!!

      (Not that it will ever be read, though )

      .
      sigpic
      mine: 2000 Honda GoldWing GL1500SE and 1980 GS850G'K' "Junior"
      hers: 1982 GS850GL - "Angel" and 1969 Suzuki T250 Scrambler
      #1 son: 1986 Yamaha Venture Royale 1300 and 1982 GS650GL "Rat Bagger"
      #2 son: 1980 GS1000G
      Family Portrait
      Siblings and Spouses
      Mom's first ride
      Want a copy of my valve adjust spreadsheet for your 2-valve per cylinder engine? Send me an e-mail request (not a PM)
      (Click on my username in the upper-left corner for e-mail info.)

      Comment


        #4
        I still see ten, Ed. Your 11 is 12.
        http://img.photobucket.com/albums/v5...tatesMap-1.jpg

        Life is too short to ride an L.

        Comment


          #5
          13) Being too cheap to buy new parts or take it to a shop.

          Comment


            #6
            Originally posted by Graham View Post
            13) Being too cheap to buy new parts or take it to a shop.
            Added my own 13) after reading this post...
            Ed

            To measure is to know.

            Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

            Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

            Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

            KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

            Comment


              #7
              Originally posted by Steve View Post


              That needs to be made a STICKY!!

              (Not that it will ever be read, though )

              .

              I read it...and I resemble a couple of these comments...course I am learning
              Cowboy Up or Quit. - Run Free Lou and Rest in Peace

              1981 GS550T - My First
              1981 GS550L - My Eldest Daughter's - Now Sold
              2007 GSF1250SA Bandit - My touring bike

              Sit tall in the saddle Hold your head up high
              Keep your eyes fixed where the trail meets the sky and live like you ain't afraid to die
              and don't be scared, just enjoy your ride - Chris Ledoux, "The Ride"

              Comment


                #8
                14) Not taking time to find a good shop.

                Comment


                  #9
                  15) Not listening to, accepting, and respecting advice given here without arguing.
                  Cowboy Up or Quit. - Run Free Lou and Rest in Peace

                  1981 GS550T - My First
                  1981 GS550L - My Eldest Daughter's - Now Sold
                  2007 GSF1250SA Bandit - My touring bike

                  Sit tall in the saddle Hold your head up high
                  Keep your eyes fixed where the trail meets the sky and live like you ain't afraid to die
                  and don't be scared, just enjoy your ride - Chris Ledoux, "The Ride"

                  Comment


                    #10
                    Originally posted by cowboyup3371 View Post
                    15) Not listening to, accepting, and respecting advice given here without arguing.
                    That should be number 1.

                    Comment


                      #11
                      Hi,

                      Hmmmm, do I see new entries for the "mega-welcome"?

                      Let's hope it helps the new owners this spring.

                      Thanks Ed!


                      Thank you for your indulgence,

                      BassCliff

                      Comment


                        #12
                        I'll throw a couple out there for the group,

                        Running OEM suspension front or back with the reasoning "I don't ride that hard". Unfortunately with all the cell phoning and texting cars on the road the likelyhood you will never have a panic stop or emergency avoidance manuver is very slim. Good suspension and sticky tires WILL give you the best chance of avoiding a bad outcome.

                        Check your tire date codes and replace them if they are over three years old with the many good tire options in all price ranges. This will require a search.

                        Replacing your old tires and not replacing the most likely OEM valve stems.

                        Reading through Cliffs site. All of the information needed for proper maintenance and lots of troubleshooting tips are there.
                        82 GS850L - The Original http://s224.photobucket.com/albums/d...ePics067-1.jpg
                        81 GS1000L - Brown County Hooligan http://s224.photobucket.com/albums/d...ivePics071.jpg
                        83 GS1100L - Super Slab Machine http://s224.photobucket.com/albums/d...t=DCP_1887.jpg
                        06 KLR650 - "The Clown Bike" :eek: http://s224.photobucket.com/albums/d...nt=SERally.jpg
                        AKA "Mr Awesome" ;)

                        Comment


                          #13
                          The most important.

                          Not having a charged fire exting. On hand and near by while working on the GS.

                          Comment


                            #14
                            Ranger, your trials regarding an extinguisher prompted me to request one for christmas from my Mom......good idea....

                            Comment


                              #15
                              Originally posted by Ranger View Post
                              The most important.

                              Not having a charged fire exting. On hand and near by while working on the GS.
                              Got one

                              Thinking restoring a bike or modifying will be cheap.

                              Comment

                              Working...
                              X