Announcement

Collapse
No announcement yet.

stuck drain plug gasket..:(

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
    #1

    stuck drain plug gasket..:(

    OK..I haven't done this in like almost 40 yrs Seems the gasket is on plug don't it?? I was given/have actually 2 new ones and would like to use it but can't remove old one!!! I tried slightly to get on the backside with a small flathead while tapping it..then a razorblade knife to try to get behind to pry..no luck. Hate to booger up the plug and then have to find and go buy a new one
    Last edited by Guest; 10-16-2012, 09:17 PM.
    Tags: None
    #2
    Vice it up and get a little more aggressive to see if you can get it to move. once you can get it away from the base a little bit, you can hold it with some pliers and use a wrench to basically unscrew it off the threads.
    MY BIKES..1977 GS 750 B, 1978 GS 1000 C (X2)
    1978 GS 1000 E, 1979 GS 1000 S, 1973 Yamaha TX 750, 1977 Kawasaki KZ 650B1, 1975 Honda GL1000 Goldwing, 1983 CB 650SC Nighthawk, 1972 Honda CB 350K4, 74 Honda CB550

    NEVER SNEAK UP ON A SLEEPING DOG..NOT EVEN YOUR OWN.


    I would rather trust my bike to a "QUACK" that KNOWS how to fix it rather than a book worm that THINKS HE KNOWS how to fix it.

    Comment

      #3
      PS....Do NOT use any heat..youll ruin the magnet in the center of the plug.
      MY BIKES..1977 GS 750 B, 1978 GS 1000 C (X2)
      1978 GS 1000 E, 1979 GS 1000 S, 1973 Yamaha TX 750, 1977 Kawasaki KZ 650B1, 1975 Honda GL1000 Goldwing, 1983 CB 650SC Nighthawk, 1972 Honda CB 350K4, 74 Honda CB550

      NEVER SNEAK UP ON A SLEEPING DOG..NOT EVEN YOUR OWN.


      I would rather trust my bike to a "QUACK" that KNOWS how to fix it rather than a book worm that THINKS HE KNOWS how to fix it.

      Comment

        #4
        so you would agree that the gasket IS indeed still on there? As everything else..my eyes are ****tin the bed with age

        Comment

          #5
          they are just aluminum and can get squished on there pretty stubbornly...I would try all I can to be sure and satisfied its either there or thats just the way that one was machined..I dont have it , or another in front of me to tell for sure. I you treid the utility blade then most likely its not there. Have you looked to see if it is stuck to the oil pan?? By the way, the washer on a spark plug is the same thing as a drain plug just for future reference. Save a few plug washers just for backup sake.
          MY BIKES..1977 GS 750 B, 1978 GS 1000 C (X2)
          1978 GS 1000 E, 1979 GS 1000 S, 1973 Yamaha TX 750, 1977 Kawasaki KZ 650B1, 1975 Honda GL1000 Goldwing, 1983 CB 650SC Nighthawk, 1972 Honda CB 350K4, 74 Honda CB550

          NEVER SNEAK UP ON A SLEEPING DOG..NOT EVEN YOUR OWN.


          I would rather trust my bike to a "QUACK" that KNOWS how to fix it rather than a book worm that THINKS HE KNOWS how to fix it.

          Comment

            #6
            yea I realize all that..Thanks

            Comment

              #7
              I recently had to remove one of these lovely washers. It was not aluminum, it was steel, and I did not get it off in one piece. Basically used a knife blade to get behind it and pry it up until I could grab it with pliers.

              Comment

                #8
                I hate those gaskets, I don't try to remove them, I don't have any leaks. But if I did try to remove them (and I would be successful to the point of destroying them in the process if need be) I would be replacing those with these. I've used them in the past with great results, reusable and no leaky.
                sigpic
                Steve
                "The world is a book, and those who do not travel read only one page."
                _________________
                '79 GS1000EN
                '82 GS1100EZ

                Comment

                  #9
                  got it off!
                  Last edited by Guest; 10-16-2012, 09:17 PM.

                  Comment

                    #10
                    Originally posted by slyone View Post
                    got it off!


                    Just so you know, you can also get replacement plugs at your local auto parts store for just a couple of bucks.

                    If the oil pan threads are getting loose, you can get an oversize plug (cuts deeper threads) for the same couple of bucks.

                    .
                    sigpic
                    mine: 2000 Honda GoldWing GL1500SE and 1980 GS850G'K' "Junior"
                    hers: 1982 GS850GL - "Angel" and 1969 Suzuki T250 Scrambler
                    #1 son: 1986 Yamaha Venture Royale 1300 and 1982 GS650GL "Rat Bagger"
                    #2 son: 1980 GS1000G
                    Family Portrait
                    Siblings and Spouses
                    Mom's first ride
                    Want a copy of my valve adjust spreadsheet for your 2-valve per cylinder engine? Send me an e-mail request (not a PM)
                    (Click on my username in the upper-left corner for e-mail info.)

                    Comment

                      #11
                      cool, Thanks for the tip..though mine are in excellent shape...luckily! I got all my oils replaced today. Now just have to do the carbs and valves and all the pm will be done!

                      Comment

                      Previous template Next
                      Working...
                      X