Announcement

Collapse
No announcement yet.

Rotating engine with shims removed?

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
    #1

    Rotating engine with shims removed?

    OK, I am not a newb to building and working on motorcycle engines, but my GS is the first one that I have had with over the bucket shims.

    I took my valve clearances today, and had 6 out of spec. I used the zip tie method to remove the shims so I could take them to my friends shop to exchange them. The thread that explains that method actually tells you to make two so you can remove two at a time.

    Now I came back to the forum and read several posts warning to NEVER rotate an engine without shims, but no one seems to explain why. Now I am trying to figure out what could possibly get damaged by hand barring the motor with shims removed. It can't be valve/piston interference, 'cause the valves will actually open less. As I said, this is not the first time I have built an engine, but maybe there is something specific to 8 valve GS motors I don't know. What am I missing here?

    I am a little concerned, as I did have to rotate the engine

    Someone please explain.
    1979 GS550, 2003 R6, 1998 XR400 Dual Sport, 2004 V-Star.........

    Decisions, decisions, what to ride, today.
    sigpic
    My GS550 Build
    Tags: None
    #2
    Because the edges of the cam lobes get torn up and so do the edges of the buckets. If the edges of the buckets get thrashed the shims might not go back in. usually its just the very slag on the edges of the lobes that gets scraped off, but still why allow it to happen in the first place!!!
    MY BIKES..1977 GS 750 B, 1978 GS 1000 C (X2)
    1978 GS 1000 E, 1979 GS 1000 S, 1973 Yamaha TX 750, 1977 Kawasaki KZ 650B1, 1975 Honda GL1000 Goldwing, 1983 CB 650SC Nighthawk, 1972 Honda CB 350K4, 74 Honda CB550

    NEVER SNEAK UP ON A SLEEPING DOG..NOT EVEN YOUR OWN.


    I would rather trust my bike to a "QUACK" that KNOWS how to fix it rather than a book worm that THINKS HE KNOWS how to fix it.

    Comment

      #3
      Many are gonna chime in and tell ya your F#$%ed and you gotta replace the cams and all kinds of bullchit. Yes take a good look at the lobes with some good magnification and be sure the actual lobe faces arent scratched or damaged.. but if its just the slag on the very very edges its not an issue.

      I am gonna get flamed by that statement, but its just the simple truth. my dad worked at GM for 20 years and he heard hundreds of them hit the floor all day and they were put in engines and no problems. I know of 3 bikes right now ( not mine by the way ) that guys had done this and never and issue..AS LONG AS THE LOBE FACES show absoultely no damage.
      MY BIKES..1977 GS 750 B, 1978 GS 1000 C (X2)
      1978 GS 1000 E, 1979 GS 1000 S, 1973 Yamaha TX 750, 1977 Kawasaki KZ 650B1, 1975 Honda GL1000 Goldwing, 1983 CB 650SC Nighthawk, 1972 Honda CB 350K4, 74 Honda CB550

      NEVER SNEAK UP ON A SLEEPING DOG..NOT EVEN YOUR OWN.


      I would rather trust my bike to a "QUACK" that KNOWS how to fix it rather than a book worm that THINKS HE KNOWS how to fix it.

      Comment

        #4
        Gotcha, Thanks.
        1979 GS550, 2003 R6, 1998 XR400 Dual Sport, 2004 V-Star.........

        Decisions, decisions, what to ride, today.
        sigpic
        My GS550 Build

        Comment

          #5
          And by NO DAMAGE I mean other than the " normal" wear in marks one would expect to see on the lobe faces.

          And always install shims with the numbers FACING THE CYLINDERS. This is so under normal wearing conditions the lobes dont rub the numbers off them..youll want to be able to read them..as well as physically measure them with good calipers..next time you do a valve adjustment. make sense???
          MY BIKES..1977 GS 750 B, 1978 GS 1000 C (X2)
          1978 GS 1000 E, 1979 GS 1000 S, 1973 Yamaha TX 750, 1977 Kawasaki KZ 650B1, 1975 Honda GL1000 Goldwing, 1983 CB 650SC Nighthawk, 1972 Honda CB 350K4, 74 Honda CB550

          NEVER SNEAK UP ON A SLEEPING DOG..NOT EVEN YOUR OWN.


          I would rather trust my bike to a "QUACK" that KNOWS how to fix it rather than a book worm that THINKS HE KNOWS how to fix it.

          Comment

            #6
            Yeah, I will look at the buckets and lobes tomorrow. I never rely on the # on the shim. I always measure. Worst case would be replace some buckets and polish the cams a bit. If you look at the edges of the cam lobes on some of the more modern engines you'd be surprised how jagged they are, so I am not too worried about that.

            Most of the engines I have dealt with are either shim under bucket or rocker arm adjusted, so this was just something I was not aware of, and is not mentioned in the manual.
            1979 GS550, 2003 R6, 1998 XR400 Dual Sport, 2004 V-Star.........

            Decisions, decisions, what to ride, today.
            sigpic
            My GS550 Build

            Comment

              #7
              You're right..it's not mentioned in the manual. I rotated with a shim out and did shave a little off the edge, but was able to get the shim back in and, despite all my fears, I've never had an issue.

              Still, I did it without realizing what the risk was. I sure wouldn't do it again.

              Oh, I also made sure to get search for all the metal shavings and get them out.

              Comment

                #8
                good pencil magnet works wonders.
                MY BIKES..1977 GS 750 B, 1978 GS 1000 C (X2)
                1978 GS 1000 E, 1979 GS 1000 S, 1973 Yamaha TX 750, 1977 Kawasaki KZ 650B1, 1975 Honda GL1000 Goldwing, 1983 CB 650SC Nighthawk, 1972 Honda CB 350K4, 74 Honda CB550

                NEVER SNEAK UP ON A SLEEPING DOG..NOT EVEN YOUR OWN.


                I would rather trust my bike to a "QUACK" that KNOWS how to fix it rather than a book worm that THINKS HE KNOWS how to fix it.

                Comment

                  #9
                  Hi,

                  For your reference:

                  Valve Adjustments (8 Valve) <--Click here (PDF file).


                  Thank you for your indulgence,

                  BassCliff

                  Comment

                  Previous template Next
                  Working...
                  X