• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

Exhaust Valve

  • Thread starter Thread starter knotzilla
  • Start date Start date
That's not really a crack -- that's erosion from high exhaust gas temps.

I have two GS850 exaust valves sitting in my toolbox that look much worse than that!

I keep them as a reminder to NEVER continue riding a bike showing symptoms of a lean mixture. It's sort of like keeping a severed head on a stake to remind visitors to behave...

Anyway, my exhaust valves burned out several years ago, before I knew about this site. I later found out the cause of the tragedy was leaking intake o-rings, along with crumbled foam seals in the airbox.

All the above led to extremely lean running, which means extremely high exhaust gas temperatures, and leads to nauseating sights like that exhaust valve.

I rebuilt the carbs many times, I cursed, I wailed, I replaced the ignition system, I checked the air pressure in the tires and the supply of blinker fluid. None of it did any good because I had no idea those intake o-rings even existed -- the manual made no mention of them. Tragically, I continued to ride the bike despite the fact it would barely get from one place to another.

Here's a longer summary of the problem:
http://cycleorings.com/intake.html

Here's the cure:
http://bwringer.com/gs/intakeorings.html

You can still order new valves from Suzuki -- they're $30.16 :shock: from the fiche at http://flatoutmotorcycles.com , which is probably the cheapest price you're going to find.

http://www.z1enterprises.com/ is a good source for the gasket set.
 
My plugs are a bit on the white/grey side. Would lowering the diaphragm needle 1 notch be too much or should I add a spacer washer. Thanks Ted
 
You do not need to make changes to the carbs if you have the stock exhaust and airbox. You do need to make sure the airbox is sealed so that air only gets in where it's supposed to, and you also need to make sure you don't have any intake leaks via bad intake boots or o-rings.

Make sure both side covers on the airbox are sealed with weatherstripping foam. You will also need to use the foam to seal the top of the metal air filter "cage" so that there's a nice tight seal against the top of the airbox.

If you have an aftermarket or altered exhaust or have discarded or altered the airbox, then, um, good luck. You will need to make jetting changes to the carbs, but there is no all-purpose recipe for doing this. You will have to experiment and read the plugs, and you'll get really good at removing the carbs.
 
knotzilla said:
My plugs are a bit on the white/grey side. Would lowering the diaphragm needle 1 notch be too much or should I add a spacer washer. Thanks Ted
Click to expand...

Oh look, there's a linky thingy I didn't see earlier. DOH!

OK, you seem to have the stock airbox and an aftermarket exhaust. You definitely want to keep the airbox -- getting these carbs to work right with pods can be challenging.

To richen the midrange mixture, you'd actually want to RAISE the needles using teensy washers -- IIRC, you can get teensy washers that will work at Radio Shack. Start with one washer under each needle and see how that works.

You also will need to play around with the idle screws and float heights to get a good off-idle transition. You might need to drop the float heights by 1/2mm - 1mm.

You may not need a larger main jet, but once it's idling well and working nicely in the transition and midrange, you might do some full-throttle plug reads and see. The stock jets are 115, so you might maybe possibly need to go to 117.5 or 120.

AFAIK, there aren't any Dynajet kits available for the GS850, but all the pieces you might need are available.
 
I have the stock air box and a 4 into 1 exhaust. The intake boots are in good shape. Would a slight popping noise from the exhaust during deacceleration in the 3000 rpm range indicate a lean mixture. Thanks Ted
 
knotzilla said:
I have the stock air box and a 4 into 1 exhaust. The intake boots are in good shape. Would a slight popping noise from the exhaust during deacceleration in the 3000 rpm range indicate a lean mixture. Thanks Ted
Click to expand...

Yes -- popping is a lean mixture. It can also be caused by intake or exhaust leaks, so make sure that's squared away. In your case, since you've pretty well gone through that, odds are it's the jetting.

With the 4 into 1 exhaust, you will definitely be running lean with stock jetting. Lean=hot=not good for exhaust valves...
 
You must log in or register to reply here.
Back
Top