• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

My new (to me) GS850 just got knocked over! Tips on what to check?

  • Thread starter Thread starter ironsheik
  • Start date Start date
I

ironsheik

Guest
Hey all,
I just got this beautiful 79 850 with only 11,000 miles on it and one week later this dumb a-hole in a giant SUV runs my bike over while leaving her parking spot! I specifically left close to 10 feet between us too! Luckily there's only a minor dent in the tank with no crease and all the other damage is cosmetic except for the busted plug wire. I just ordered a new brake lever, rear turn signal, handlebar, badge and crankcase cover which she will pay for. It happened last night and I discovered her truck parked in the same spot this morning. There was a nice gash in her bumper where it rammed the fins. Luckily it's plastic and luckily she came out as I was inspecting it!

The thing I'm not sure about though is how do I check front end alignment? The handlebar is bent a lot and it looks to me like the guages and turnsignals are slightly shifted to the left. The bike was completely over on it's side and the front wheel was locked. Would this indicate any damage to the triple clamp? I kind of doubt that thing would get bent but obviously want to be sure. I'm waiting for the Clymer right now so I don't know too much about these bikes yet.

Thanks for any advice. I just hope I'm not looking at an expensive repair that I have to shake someone down for. I DO know where she lives and what she drives though... Just in case...

Josh
 
Its not that hard to straighten your handlebars out. Loosen the bolts on your lower and upper triple clamps, and the one clamp on your steering head, (not the big one on top, but the clamp bolt that is at the base by your gas tank). Put a brace under your bike to keep the bike from falling, or just loosen the triple clamp bolts just a little, so the front end of the bike doesn't slip down the fork tubes.

Then with your bike on the centerstand, you should be able to straddle the front tire with your legs and line up your handlebars with your arms.

I doubt that if your bike simply fell over that there should be any misalignment unless the whole front end was run over. But once your bars are straightened, check all your bolts on the front end for proper torque and for smooth operation of your forks.
 
Thanks Mark. That's good to hear. I thought it wasn't too serious but I'm still new to motorcycles.

It's funny this happened because I actually needed a new master cylinder, lower handlebars and plug wires anyway. Thank God the tank wasn't damaged too much. I heard of fixing dents with a hairdryer and compressed air by heating and then super-cooling the metal. Hopefully it works on this!

Josh
 
ironsheik said:
I heard of fixing dents with a hairdryer and compressed air by heating and then super-cooling the metal. Hopefully it works on this!

Josh
Click to expand...

I'll have to try that on a few of the dents in my tank. (lol).
 
For your tank, there are people out there that can remove the dent(s) from the inside out. I forget what the method is called, but it really sounds like the best method for your needs.
As far as the forks and triple clamps, be sure and ride it after adjusting it. When you are going down a flat, smooth road, you should be able to let go of the handlebars and the bike should track straight and true.
Personally, since she should be paying for it, I would take it to the dealer and have it done right. But that's just me.
 
koolaid_kid said:
Personally, since she should be paying for it, I would take it to the dealer and have it done right. But that's just me.
Click to expand...

Agreed however I like working on my own bike and seriously I'm just happy she admitted it and is going to pay anything. I'm one of those people that doesn't trust a thing unless I do it myself. Thanks for all the advice everyone!

Josh
 
ironsheik said:
Agreed however I like working on my own bike and seriously I'm just happy she admitted it and is going to pay anything. I'm one of those people that doesn't trust a thing unless I do it myself. Thanks for all the advice everyone!

Josh
Click to expand...
I agree with you on the trust issue...especially on these old school bikes. Most of the dealerships have 20-25 year old kids who have a little crotch-rocket experience and not much else. If it's not fuel injected they are clueless.
 
ironsheik said:
Agreed however I like working on my own bike and seriously I'm just happy she admitted it and is going to pay anything. I'm one of those people that doesn't trust a thing unless I do it myself. Thanks for all the advice everyone!

Josh
Click to expand...

My advice, since she is going to pay. Take it to a bike shop that is familiar with older bikes. They do exsist! And get an estimate from them. Then take it to a body shop (you may have to shop around) and get an estimate for the body work. While I understand the want to work on your own bike, she's going to pay! Leave it to the pros and sit back and relax while your bike is brought back to life.

Brad bt
 
Must of hit you good. A simple fall over would yield a scratch and a few explicatives afterwards if you saw it. (A major gust of wind caught mine, nothing for damage though) Be careful on the initial road test in case something was missed, front end stuff can be hairy.
 
DO NOT PRESSURISE THE TANK WITH AIR. It will balloon & you will be looking for a replacement
 
You must log in or register to reply here.
Back
Top