Announcement

Collapse
No announcement yet.

cv fuel bowl small hole?

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    cv fuel bowl small hole?

    i,m having problems clearing the small hole on the cv carb bowl {81 gs550e} have tried fine guitar wire as in the carb cleaning thread on page 41 of 53 and it just wont clear, how small is the hole and can it be drilled out with a dremmel with, say a 1mm bit , or is there no hole on this model, have soaked them and tried for about 1-2 hrs to clear it , if this was left as is ,what would the symptoms be.
    greatfull of any ideas

    #2
    If it is the hole I'm thinking of, the one on the rim of the bowl itself, it is for the idle circuit (I think) . Can you get a picture of it, so we can see exactly what you're looking at?

    Comment


      #3
      dave, its where the hole goes down from the top of the bowl and meets a diaganal hole from the inside base , havent sussed out the photo posting yet but its the one shown in the carb cleaning series on page 41 of 53 on the forum.

      Comment


        #4
        Page #41? Picture #41...

        Comment


          #5
          appologies, i thought the pdf file i had been looking at was downloaded from GS resources, it was a pdf file on carb rebuildng 53 pages long and the bowl vent hole cleaning precedure was on page 41, sorry for the confusion, no i dont know where i downloaded it from,
          cheers

          Comment


            #6
            Did you soak the floatbowl in carb dip yet?
            Ed

            To measure is to know.

            Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

            Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

            Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

            KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

            Comment


              #7
              yes to your question, just found that it was off Bike cliffs webpage/site where i downloaded the pdf file.
              ta

              Comment


                #8
                This page then....

                Yes there is a hole there & yes you need to clear it... Mine were pretty clean but I made double sure by squirting Gum out through them with the straw inserted so it was under pressure... Be careful you don't get an eyeful. There shouldn't be anything in there that tough that you can't clear with a paperclip or something, it just joins to the other hole like you said...

                Good luck,

                Dan
                1980 GS1000G - Sold
                1978 GS1000E - Finished!
                1980 GS550E - Fixed & given to a friend
                1983 GS750ES Special - Sold
                2009 KLR 650 - Sold - gone to TX!
                1982 GS1100G - Rebuilt and finished. - Sold
                2009 TE610 - Dual Sporting around dreaming of Dakar..... - FOR SALE!

                www.parasiticsanalytics.com

                TWINPOT BRAKE UPGRADE LINKY: http://www.thegsresources.com/_forum...e-on-78-Skunk/

                Comment


                  #9
                  if that hole in the picture is the one you are talking about, put the spray style carb cleaner with it's red straw thing on the bottom hole and point the thing away from your face and spray. I also used a cotton swab to get mine clean, but the directions on the pdf file work very very well.

                  Comment


                    #10
                    If the hole is clogged after several hours in the dip, put them back in. Carb dip is not as agressive as it used to be and takes a while to work in some cases. Spray cleaner will help push out any soft sludge but it won't help for hard varnish.

                    Good luck.
                    Ed

                    To measure is to know.

                    Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182

                    Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846

                    Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf

                    KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection

                    Comment


                      #11
                      thanks all for your tips, it still wouln,t clear so i ended up using a fine/small bit approx 1mm and dremmell , cleared it but noticed a small amount of bras swarf in with the crap , so all i can assume is that they have a small brass reducer inside the bottom of that hole, may be i,ve knackered the bowls but i wont know untill i,ll give it a try with the carbs back on the bike
                      cheers


                      81 gs550e CV carbs

                      Comment


                        #12
                        If you've killed it & the 32's are the same size as the 34's I likely have a spare....

                        Dan
                        1980 GS1000G - Sold
                        1978 GS1000E - Finished!
                        1980 GS550E - Fixed & given to a friend
                        1983 GS750ES Special - Sold
                        2009 KLR 650 - Sold - gone to TX!
                        1982 GS1100G - Rebuilt and finished. - Sold
                        2009 TE610 - Dual Sporting around dreaming of Dakar..... - FOR SALE!

                        www.parasiticsanalytics.com

                        TWINPOT BRAKE UPGRADE LINKY: http://www.thegsresources.com/_forum...e-on-78-Skunk/

                        Comment


                          #13
                          a spare one or a spare full set of 4, as the full set of 4 needed cleaning/drilling

                          Comment

                          Working...
                          X