Thanks again all.
Announcement
Collapse
No announcement yet.
Cleaning the Air Cleaner
Collapse
X
-
DarkOnyx
Originally posted by catbed View Post
Thanks again all.
-
My mistake.Sorry gents.I thought we were talking paper filters.I would still put in a new filter so you have a good place to start a bit of bike history for your own reference.Cheers,Simon.http://i258.photobucket.com/albums/h...esMapSimon.jpg
'79 GS1000S my daily ride in Aus
'82 (x2) GS650ET in the shed
Comment
-
Forum LongTimerGSResource Superstar
Past Site Supporter
Super Site Supporter- Mar 2006
- 35622
- Torrance, CA
I thought the filter cover is on the right side of the bike?Ed
To measure is to know.
Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182
Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846
Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf
KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection
Comment
-
catbed
the cover you see in my sig is not the cover to remove the filter. the other side of the bike is, #4 cylinder side, brake side, whatever. its the right side that you can remove the air filter. should only have one screw.
Comment
-
Originally posted by catbed View Postthe cover you see in my sig is not the cover to remove the filter. the other side of the bike is, #4 cylinder side, brake side, whatever. its the right side that you can remove the air filter. should only have one screw.
I was pretty sure I put mine in from the left... Could be wrong, I suppose. It was only last week. No matter. It's in there somewhere.Dogma
--
O LORD, be gracious to me; heal me, for I have sinned against you! - David
Skeptical scrutiny is the means, in both science and religion, by which deep insights can be winnowed from deep nonsense. - Carl Sagan
--
'80 GS850 GLT
'80 GS1000 GT
'01 ZRX1200R
How to get a "What's New" feed without the Vortex, and without permanently quitting the Vortex
Comment
-
Roostabunny
Originally posted by Nessism View PostGS850 takes a foam filter. Proper maintainance technique is to soak it in solvent, let dry, oil it, reinstall. No need to replace it unless the foam is deteriorated - which does occur, but takes a number of years.
Comment
-
DarkOnyx
Originally posted by catbed View Postthe cover you see in my sig is not the cover to remove the filter. the other side of the bike is, #4 cylinder side, brake side, whatever. its the right side that you can remove the air filter. should only have one screw.
Intersting. The manual says that it's on the left side. Just to be certain "air cleaner" and "air filter" are synonymous right?
Comment
-
Originally posted by DarkOnyx View PostIntersting. The manual says that it's on the left side. Just to be certain "air cleaner" and "air filter" are synonymous right?
OK, I made that up. These terms should be synonymous, referring to the foam thing in the bottom half of your air box.Dogma
--
O LORD, be gracious to me; heal me, for I have sinned against you! - David
Skeptical scrutiny is the means, in both science and religion, by which deep insights can be winnowed from deep nonsense. - Carl Sagan
--
'80 GS850 GLT
'80 GS1000 GT
'01 ZRX1200R
How to get a "What's New" feed without the Vortex, and without permanently quitting the Vortex
Comment
-
Forum LongTimerBard Award Winner
GSResource Superstar
Past Site Supporter
Super Site Supporter- Oct 2003
- 17441
- Indianapolis
I wash my air filter element with warm water and dish soap.
In the kitchen sink.
When my wife isn't looking.
When you re-oil, use very, very, very, very little oil. Don't soak it in 10W-40 and stuff the drippy mess back in there, or it'll be badly restricted. If you can squeeze the foam with a paper towel and still get any oil on the paper towel, there's still too much oil.
About two seconds with a spray can of foam filter oil, available at any auto parts store, is plenty.
If it's a K&N, get a clean and recharge kit from your local auto parts store. Don't try to fart around with homemade substitutes.1983 GS850G, Cosmos Blue.
2005 KLR685, Aztec Pink - Turd II.3, the ReReReTurdening
2015 Yamaha FJ-09, Magma Red Power Corrupts...
Eat more venison.
Please provide details. The GSR Hive Mind is nearly omniscient, but not yet clairvoyant.
Celeriter equita, converteque saepe.
SUPPORT THIS SITE! DONATE TODAY!
Co-host of "The Riding Obsession" sport-touring motorcycling podcast at tro.bike!
Comment
-
I'll second that on the amount of oil. I tried the aerosol filter oil and followed its instructions to spray it long and hard and soak the filter. Bike would barely run after that. The oil is there for dust to adhere to, nothing more.sigpic[Tom]
“The greatest service this country could render the rest of the world would be to put its own house in order and to make of American civilization an example of decency, humanity, and societal success from which others could derive whatever they might find useful to their own purposes.” George Kennan
Comment
-
Silly me, I followed the instructions in the service manual that said to soak it and squeeze the excess out by hand. A laundry wringer would be more like it. Fortunately I had what I needed to deal with the big puddle of oil that appeared under the bike the next day. It does run alright though, and only makes a few drips by the next day. I'm hoping a good long ride will suck the excess out and rectify that situation.Dogma
--
O LORD, be gracious to me; heal me, for I have sinned against you! - David
Skeptical scrutiny is the means, in both science and religion, by which deep insights can be winnowed from deep nonsense. - Carl Sagan
--
'80 GS850 GLT
'80 GS1000 GT
'01 ZRX1200R
How to get a "What's New" feed without the Vortex, and without permanently quitting the Vortex
Comment
-
Forum LongTimerGSResource Superstar
Past Site Supporter
Super Site Supporter- Mar 2006
- 35622
- Torrance, CA
My experience in terms of oiling is to give the filter a good gurgle of engine oil. Squeeze the filter with your hand a few times to distribute it evenly through out the filter. After that, give the thing a hard squeeze to get out as much excess as you can. Follow that up with some light blotting with a clean paper towel. I like the filter to be wet, but not excessively so.
Hope this helps.Ed
To measure is to know.
Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182
Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846
Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf
KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection
Comment
-
Johnny K
Comment