Thanks, yes I am quite confident so far but I am the analytical type thus also want to know why and the cam chain o-ring still bothers me a bit. I just need someone who has actually used such a setup or knows the type of gasket to confirm.
Announcement
Collapse
No announcement yet.
Head gasket GS1000G questions
Collapse
X
-
Matchless
-
Matchless
-
AirCooledHeaven
Originally posted by Matchless View PostMark,
Thanks, yes I am quite confident so far but I am the analytical type thus also want to know why and the cam chain o-ring still bothers me a bit. I just need someone who has actually used such a setup or knows the type of gasket to confirm.
Comment
-
Matchless
I noticed that on the photo as well. The butter holders are right behind just getting into the picture, they should be in there. Should have nailed some coke bottle caps next to each valve.
What oil do you suggest for the cylinder honing? I have a bottle of water soluble oil that I was planning to use with the hand honer and drill at 100rpm, and 3 silicon graphite stones. Opinions differ greatly here it seems.
Comment
-
since the cam chain tunnel has a grove quite close to the very edge i would still use the oring under the gasket
as for the crush washers for the outer studs, i'd use them only if you think they would impress into the gasket (if the gasket is soft enough for that to happen)
if the gasket appears stronger than that (and the crush washers would not sit IN the gasket) i'd use a very small amount of silicone around the outer studs holes on the gasket (top and bottom of the gasket)GS850GT
Comment
-
Matchless
Originally posted by psyguy View Postsince the cam chain tunnel has a grove quite close to the very edge i would still use the oring under the gasket
as for the crush washers for the outer studs, i'd use them only if you think they would impress into the gasket (if the gasket is soft enough for that to happen)
if the gasket appears stronger than that (and the crush washers would not sit IN the gasket) i'd use a very small amount of silicone around the outer studs holes on the gasket (top and bottom of the gasket)
That makes good sense. I am doubtfull that the crush washers will indent into the gasket or fit inside the hole as it is made up of 3 layers of flat sheet metal and the old gasket did not have any there and did not leak as the coating on the outer layers seems to be the magic here. I think a spot of silicon as you mentioned is an excellent idea just to make doubly sure.
The o-ring should compress enough as the channel is wider than the ring and I really will only feel happy leaving it out if someone can tell me why and that is someone who has real practical experience with the same gasket. This gasket also does not have edges folded over and the three bare edges of the layers face the cylinder compression and the oil pressure and the old one again was the same and worked.
Thanks for the suggestions
Comment
-
cranemonkey
more head gasket issues...
Sooo, I'm putting the motor of my 83GS850GL back together (after a brake job--don't ask), and I have one of these 4 layer head gaskets like in the previous posts. I install the rectangular o-ring (which does not sit nicely in the cutout) and the gasket and set the head on it. My problem is that there seems to be something preventing the head from sitting flat --I can rock it back and forth at its most downward point and there is 1/32 inch of play. Not liking this, I took everything off again and installed just the head. It sits flat-no play. I put the head gasket in and put back together-no play. I put the rec. o-ring back in and voila!! it rocks. My conclusion--the o-ring is preventing the head from sitting flat, and leaves a gap, not to mention the seemingly obscure stress of bending the head down on both side when torqued. I don't recall if the previous head gasket had a cutout for the rectangular o-ring or not. QUESTION: does original equipment head gasket cover the rec. o-ring, and if not, does the new 4 layer head gasket which sits on top of the rect. o-ring seal as the oring does? I am not happy with the way the recently machined surfaces come together and don't want to do this but one time. I have read all of the previous posts but am still unsure of if the o-ring is a critical component with this new head gasket. More thoughts? Matchless, thanks for posting your same issue--thought maybe I was crazy. You didn't relieve that concern, but maybe some one out there (psyguy, aircooledheaven) can definatively answer this tech issue. I sure would like to ride this year but only gonna rip into this thing one time.
Comment
-
Matchless
Originally posted by cranemonkey View PostSooo, I'm putting the motor of my 83GS850GL back together (after a brake job--don't ask), and I have one of these 4 layer head gaskets like in the previous posts. I install the rectangular o-ring (which does not sit nicely in the cutout) and the gasket and set the head on it. My problem is that there seems to be something preventing the head from sitting flat --I can rock it back and forth at its most downward point and there is 1/32 inch of play. Not liking this, I took everything off again and installed just the head. It sits flat-no play. I put the head gasket in and put back together-no play. I put the rec. o-ring back in and voila!! it rocks. My conclusion--the o-ring is preventing the head from sitting flat, and leaves a gap, not to mention the seemingly obscure stress of bending the head down on both side when torqued. I don't recall if the previous head gasket had a cutout for the rectangular o-ring or not. QUESTION: does original equipment head gasket cover the rec. o-ring, and if not, does the new 4 layer head gasket which sits on top of the rect. o-ring seal as the oring does? I am not happy with the way the recently machined surfaces come together and don't want to do this but one time. I have read all of the previous posts but am still unsure of if the o-ring is a critical component with this new head gasket. More thoughts? Matchless, thanks for posting your same issue--thought maybe I was crazy. You didn't relieve that concern, but maybe some one out there (psyguy, aircooledheaven) can definatively answer this tech issue. I sure would like to ride this year but only gonna rip into this thing one time.
It seems as if the original OEM gasket and many other aftermarket types definitely did not cover the o-ring gasket indentation. The o-ring gasket sat inside the opening for the cam chain and the rubber gasket sealed cylinder metal to head metal and the head gasket did not touch the o-ring one. Now the newer gaskets cover the o-ring gasket channel completely and my question is - Why? I was thinking that if there are other makes than Suzuki with a similar sort of design from the same era maybe some reply will be forthcoming from there. I did contact the suppliers of the gasket set, but although they did reply it did not mean much, just that the set does not contain a rectangular gasket and I should get it from another supplier.
Fortunately I still have a way to go before its assembly time and hopefully more clarity comes to light soon.
Comment
-
Matchless
Some further browsing here http://www.cometic.com/faq.aspx#q7 has shown that Cometic make a MLS (Multi Layer Steel) head gasket with a Viton rubber layer on the two outer layers. They say that MLS gaskets are not to be used with o-rings or receiver grooves around the cylinder bores and a lot more.
These Athena headgaskets are very likely MLS and mine definitely has a black rubber layer on the outer and could be very similar to Cometic.
Comment
-
AirCooledHeaven
Originally posted by cranemonkey View PostSooo, I'm putting the motor of my 83GS850GL back together (after a brake job--don't ask), and I have one of these 4 layer head gaskets like in the previous posts. I install the rectangular o-ring (which does not sit nicely in the cutout) and the gasket and set the head on it. My problem is that there seems to be something preventing the head from sitting flat --I can rock it back and forth at its most downward point and there is 1/32 inch of play. Not liking this, I took everything off again and installed just the head. It sits flat-no play. I put the head gasket in and put back together-no play. I put the rec. o-ring back in and voila!! it rocks. My conclusion--the o-ring is preventing the head from sitting flat, and leaves a gap, not to mention the seemingly obscure stress of bending the head down on both side when torqued. I don't recall if the previous head gasket had a cutout for the rectangular o-ring or not. QUESTION: does original equipment head gasket cover the rec. o-ring, and if not, does the new 4 layer head gasket which sits on top of the rect. o-ring seal as the oring does? I am not happy with the way the recently machined surfaces come together and don't want to do this but one time. I have read all of the previous posts but am still unsure of if the o-ring is a critical component with this new head gasket. More thoughts? Matchless, thanks for posting your same issue--thought maybe I was crazy. You didn't relieve that concern, but maybe some one out there (psyguy, aircooledheaven) can definatively answer this tech issue. I sure would like to ride this year but only gonna rip into this thing one time.
Comment
-
AirCooledHeaven
Originally posted by Matchless View PostHi,
It seems as if the original OEM gasket and many other aftermarket types definitely did not cover the o-ring gasket indentation. The o-ring gasket sat inside the opening for the cam chain and the rubber gasket sealed cylinder metal to head metal and the head gasket did not touch the o-ring one. Now the newer gaskets cover the o-ring gasket channel completely and my question is - Why? I was thinking that if there are other makes than Suzuki with a similar sort of design from the same era maybe some reply will be forthcoming from there. I did contact the suppliers of the gasket set, but although they did reply it did not mean much, just that the set does not contain a rectangular gasket and I should get it from another supplier.
Fortunately I still have a way to go before its assembly time and hopefully more clarity comes to light soon.
Comment
-
cranemonkey
o-ring
I thought about that--there are some problems with that train of thought, though. First is I torqued down the head bolts (properly) and afterward there was still a visible gap between the head and the jug body at the center point (cam chain housing, front). If there was a gap there, certainly there would be a danger of high compression gases escaping at other points around the head. Second, as I stated in a previous post, there will be bending forces acting on the head surface. I appreciate your input, I guess I want somebody to tell me it's ok without the oring, but I doubt it...more thoughts, please. I will check manuf. sites.
Comment
-
Matchless
What I have discovered and never knew is that the new MLS aftermarket headgaskets are coated with a thicker coat of Viton rubber on the outside layers to allow for thermal movement of the heads and cylinder metal, which apparently can destroy some gaskets. The thicker layer is that MLS for OEM use requires a nearly perfectly machined surface and even small blemishes may break this seal and can cause the gasket to fail. Apparently these must be installed dry as some compounds may attack the Viton layer or inhibit the flexibility of the Viton.
The reasoning around keeping the o-ring is sound so far, but still does not give an answer as to why the o-ring is not supplied with the new Viton covered MLS gaskets in the set, but definitely included with the older type gaskets, was this an error or on purpose?
I must add that my old aftermarket gasket that came off was also MLS, but not Viton covered. It had a very thin layer of something silver, that left resues on the aluminium surface like paint and that one had been installed with the gasket under the head gasket and had run like that since 1994. It seems as it will not be a problem if you do install the o-ring under the gasket, but the question still remains as to what Anthena suggests in this case with their latest gaskets. Does anyone know if they have an presence in the USA and we could maybe try to ask them? Or even ask any other aftermarket manufacturer??
Comment
-
AirCooledHeaven
Originally posted by Matchless View PostDoes anyone know if they have an presence in the USA and we could maybe try to ask them? Or even ask any other aftermarket manufacturer??
Comment
-
if the o-ring sits too proud of the surounding surface and you think it wont easily compress under the gasket - and especially if the head gasket has a rubber coating on both outer sides - i'd leave the oring out
there is enough flat surface between the inner cylinders and the cam chain tunnel to provide a good seal given the head gasket does have that rubber surface and the head/barrels surfaces are machined flat
(2c)
.GS850GT
Comment
Comment