Announcement

Collapse
No announcement yet.

Tuning a suspension on my GS850G

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Tuning a suspension on my GS850G

    I just recently picked up a 80’ GS850G that has been sitting for probably 10+ years. I cleaned the carburetors and got it running. Now I have a few question about how to proceeded.
    1.) Plug wire insulation has some dry rot but bike seems to be getting good spark. Should I change the coils/wires now or wait until they start giving me trouble. Will these wires affect the carb sync?
    2.) fork tube is damp. Does this automatically mean bad seal, or could a flush and fluid change recondition them and get ‘em working again.
    3.) My Clymer has a table for fork spring length, but the table has no column headings and is confusing to me. The table lists two numbers for “GS850G and GS1000G”…. 421mm & 416mm; are these Min/Max, or for 850 & 1000 models respectively? Anyone know the specs for the 850 spring length?

    any other tips or suggestions with the bike would be appriciated.

    #2
    1) Plug insulation will not affect carb sync, but if you happen to get wet anywhere on a ride, that bike is AWFULLY hard to push. :shock:

    2) Damp fork tubes do not automatically mean bad seals. What you want to look for is a puddle of fluid under the dust cover or weeping down the lower tube.
    These won't affect carb sync, either.

    3) My Clymer shows the same thing for spring length, so I looked in my Haynes manual. The stock length is 421 mm, with a minimum length of 416 mm.














    Hey Cliff, ... another Newbie, Aisle 3! \\/
    sigpic
    mine: 2000 Honda GoldWing GL1500SE and 1980 GS850G'K' "Junior"
    hers: 1982 GS850GL - "Angel" and 1969 Suzuki T250 Scrambler
    #1 son: 1986 Yamaha Venture Royale 1300 and 1982 GS650GL "Rat Bagger"
    #2 son: 1980 GS1000G
    Family Portrait
    Siblings and Spouses
    Mom's first ride
    Want a copy of my valve adjust spreadsheet for your 2-valve per cylinder engine? Send me an e-mail request (not a PM)
    (Click on my username in the upper-left corner for e-mail info.)

    Comment


      #3
      Hee Haw Howdy!

      Hi Mr. gheddy,

      Stop by my website (link below) for all kinds of GS850-related goodies. Now here is your mega-welcome! \\/

      Dear fellow GS rider,

      Let it be known that on this day you are cordially and formally welcomed to the GSR Forum as a Junior Member in good standing with all the rights and privileges thereof. Further let it be known that your good standing can be improved with pictures (not you, your bike)!

      Perhaps you've already seen these, but I like to remind all the new members. In addition to the
      carb rebuild series, I recommend visiting the In The Garage section via the GSR Homepage and check out the Stator Papers. There's also a lot of great information in the Old Q&A section. I have some documentation on my little BikeCliff website to help get you familiar with doing routine maintenance tasks (note that it is 850G-specific but many tasks are common to all GS bikes). Other "user contributed" informational sites include those of Mr. bwringer, Mr. tfb and Mr. robertbarr. And if your bike uses shims for valve adjustments, send an email to Mr. Steve requesting a copy of his Excel spreadsheet that helps you keep track of clearances, shim sizes and other service work.

      These are some edited quotes from one of our dear beloved gurus,
      Mr. bwringer, with ideas on basic needs (depending on initial condition), parts, and accessories.
      ***********Quoted from Mr. bwringer************

      Carburetor maintenance:

      Replace the intake boot o-rings, and possibly the intake boots. Here's the procedure:

      Here's an overview of what happens with this particular problem:

      You'll also want to examine the boots between the carbs and the airbox. There's a good chance these are OK, but check them over.
      And finally, if things still aren't exactly right, you'll want to order a set of o-rings for BS carbs from the GS owner's best friend, Robert Barr:
      http://cycleorings.com
      Once you receive these rare rings of delight, then you'll want to thoroughly clean and rebuild your carburetors. Here are step-by-step instructions that make this simple:

      ***********************************
      Every GS850 has (or had) a set of well-known issues that MUST be addressed before you have a solid baseline for further troubleshooting. It's a vintage bike, and it's quite common (as in, every single GS850 I have had contact with) that there are multiple problems that have crept up and slowly gotten worse over the years. It's not like a newer vehicle, where there's generally one problem at a time.

      These common issues are:

      1. Intake O-rings (install NEW OEM or Viton only - common nitrile O-rings will quickly deteriorate from heat)
      2. Intake Boots (install NEW -- these cannot be repaired)
      3. Valve clearances (more important than most people think)
      4. Carb/airbox boots
      5. Airbox sealing
      6. Air filter sealing
      7. Petcock (install a NEW one)
      8. On '79 models, install new points or Dyna electronic ignition (or at least verify that the old points are working correctly)
      9. On all models, it's fairly common to have problems with the spark plug caps. These are $3 or $4 each, and often worth replacing if you're keeping the stock coils/wires.
      10. Stock exhaust with NO leaks or holes -- good seals at the head and at the junctions underneath.
      ***************************************
      OEM Parts/Online Fiches:

      I would definitely double and triple the recommendations to use Cycle Recycle II and Z1 Enterprises as much as possible. These guys are priceless resources. Z1 tends to have slightly better prices, CRC2 has a wider range of goodies available. If you're near Indy and can bring in an old part to match, CRC2 has a vast inventory of used parts.
      http://denniskirk.com - Put in your bike model and see what they have.
      http://oldbikebarn.com - seems to be slowly regaining a decent reputation, but it's still caveat emptor. They don't have anything you can't get elsewhere at a better price anyway.
      http://www.babbittsonline.com/ - Decent parts prices. Spendy shipping. Don't give you part numbers at all. Useful cross-reference if you obtain a part number elsewhere. Efficient service.
      http://bikebandit.com - Fastest. Middlin' prices. Uses their own parts numbering system to obfuscate price comparisons -- can be very confusing for large orders. Cheapest shipping, so total cost usually isn't too bad.
      http://flatoutmotorcycles.com - Slow. Cheapest parts prices, crazy shipping costs. Don't expect progress updates or much communication. Real Suzuki part numbers.
      http://alpha-sports.com - Exorbitant parts prices. Different type of fiche interface that's quite useful at times, especially with superceded part numbers. Real parts numbers. Shipping cost and speed unknown due to insane, unholy pricing.

      Stainless Bolts, Viton o-rings, metric taps, dies, assorted hard-to-find supplies and materials, etc:

      http://mcmaster.com - Fast, cheap shipping, good prices. No order minimum, but many items like bolts come in packs of 25 or 50. Excellent resource.
      http://motorcycleseatcovers.com - Great quality, perfect fit (on original seat foam), and available for pretty much every bike ever made. Avoid the textured vinyl -- it's perforated.
      http://newenough.com - You DO have riding gear, don't you? Great clearances, always outstanding prices and impeccable service.
      ***************End Quote**********************
      Additional parts/info links:

      GSR Forum member Mr. duaneage has great used upgraded Honda regulator/rectifiers for our bikes. Send him a PM.
      New electrical parts:
      http://stores.ebay.com/RMSTATOR or http://www.rmstator.com/
      Aftermarket Motorsport Electrics parts for motorcycles, dirtbikes, atvs, motosport vehicles manufactured and distributed by Rick's Motorsport Electrics


      For valve cover and breather cover gaskets, I recommend Real Gaskets (reusable silicon):
      http://www.realgaskets.com
      The Rice Paddy (salvage/used)
      http://www.ricepaddymotorcycles.com
      Carolina Cycle
      http://www.carolinacycle.com
      Ron Ayers Motorsports
      http://www.ronayers.com
      MR Cycles
      http://www.mrcycles.com
      Moto Grid
      http://www.motogrid.com
      If all else fails, try this:
      http://www.used-motorcycle-parts.org/
      Used bike buying checklists:

      http://www.clarity.net/~adam/buying-bike.html
      Lots of good info/pictures here:
      http://www.suzukicycles.org


      Thanks for joining us. Keep us informed of your progress. There's lots of good folk with good experience here.

      Thank you for your indulgence,

      BassCliff
      (The unofficial GSR greeter)

      Comment


        #4
        (Pardon my hijack, but...)

        Hey Cliff, ... another Newbie, Aisle 3!


        WOW!!! That's awesome!!!!! You just yelled for BassCliff, and there he was! Just like magic!! Tell us what your secret is!









        OK, I'm done. You can have your thread back now.

        Comment


          #5


          Tain't no secret, really, didja notice that it took him over THREE HOURS to hear that call? Can't write it off to time zone difference either.



          .
          sigpic
          mine: 2000 Honda GoldWing GL1500SE and 1980 GS850G'K' "Junior"
          hers: 1982 GS850GL - "Angel" and 1969 Suzuki T250 Scrambler
          #1 son: 1986 Yamaha Venture Royale 1300 and 1982 GS650GL "Rat Bagger"
          #2 son: 1980 GS1000G
          Family Portrait
          Siblings and Spouses
          Mom's first ride
          Want a copy of my valve adjust spreadsheet for your 2-valve per cylinder engine? Send me an e-mail request (not a PM)
          (Click on my username in the upper-left corner for e-mail info.)

          Comment


            #6
            Originally posted by Steve View Post


            Tain't no secret, really, didja notice that it took him over THREE HOURS to hear that call? Can't write it off to time zone difference either.



            .
            Some people never hear the calling, or worse still, ignore it!
            Should we really drink to that?
            :) The road to hell is paved with good intentions......................................

            GS 850GN JE 894 10.5-1 pistons, Barnett Clutch, C-W 4-1, B-B MPD Ignition, Progressive suspension, Sport Demons. Sold
            GS 850GT JE 1023 11-1 pistons. Sold
            GS1150ES3 stock, V&H 4-1. Sold
            GS1100GD, future resto project. Sold

            http://i155.photobucket.com/albums/s...s/P1000001.jpg
            http://i155.photobucket.com/albums/s...s/P1000581.jpg

            Comment


              #7
              BassCliff has definitely heard the call.
              AND answerred it.


              sigpic
              mine: 2000 Honda GoldWing GL1500SE and 1980 GS850G'K' "Junior"
              hers: 1982 GS850GL - "Angel" and 1969 Suzuki T250 Scrambler
              #1 son: 1986 Yamaha Venture Royale 1300 and 1982 GS650GL "Rat Bagger"
              #2 son: 1980 GS1000G
              Family Portrait
              Siblings and Spouses
              Mom's first ride
              Want a copy of my valve adjust spreadsheet for your 2-valve per cylinder engine? Send me an e-mail request (not a PM)
              (Click on my username in the upper-left corner for e-mail info.)

              Comment

              Working...
              X