Where can i find this fairing?

[Bubba67]

This fairing is perfect for my bike. Does anyone know what brand, kind it is and where I might find one?
Thanks

[Big T]

try Lockhart or Air Tech

[Bubba67]

try Lockhart or Air Tech

Wow, tried both of those manufacturers and found nothing similar. Tried a dozen other manufacturers and also came up empty. Just my luck, fall in love with something I can't have . Maybe I'll just go with the Dunstall look cafe fairing.

Thanks

[Zook]

Try that fancy French cycle boutique, Jaques C. Whitney.

[Carter Turk]

Emgo used to make fairings like that. Maybe Dennis Kirk or Chapparal.

[kamelman]

Here's a place I was checking out a few days ago. Don't know to much about them, but the do have a pretty good line

http://www.airtech-streamlining.com/vintage/vintagefairingsquarter.htm

[kamelman]

Sorry meant to post this. Is this what you had in mind?

[TheCafeKid]

Wow, tried both of those manufacturers and found nothing similar. Tried a dozen other manufacturers and also came up empty. Just my luck, fall in love with something I can't have . Maybe I'll just go with the Dunstall look cafe fairing.

Thanks

Bubba I think that, unless i am wrong, is simply an Emgo, or Viper or whatever fairing you would find on Ebay or any other parts supplier that may call them a "cafe" fairing that has been cut down to the owners liking. They are made of ABS, so with a dremel you could go to town and come up with a pretty nice result. I had one of those fairings on my 1100G for a bit. The fairing itself was nice, but the windscreen that came with it was flimsy and developed stress cracks around the screws. Eventually i just snapped it off. I still have the fairing, and if you can find a windscreen to fit it, lemme know and you can have it for shipping cost. The windscreen shouldnt be too difficult to locate. It mounts easily, just with some L brackets that get bolted on to the headlamp ears. Orrr if you are in no hurry, I can use the one i have here to draw a mould from, and with some direction of what youd like, we could modify the mould and probably make one out of fibreglass in a relatively short amount of time. I have a buddy who is an expert glass man (does the body work for the Miss Budweiser hydrofoil/jetboat whatever) and we are in the design stages of starting a lil custom fiberglass biz that would revolve around making replica side covers for old UJMs (zooks to start with) so this would be another facet we could delve into .

[Mellow'dOut]

That looks like an old GIVI windscreen someone matted out. Givi's aren't cheap but they are better quality than Viper, Emgo, Rifle, etc that were the common bolt on fairings. http://www.giviusa.com/caschi_borse_...asp?CO_ID=9581

[seuadr]

wow.. 245a is pure sexy 240a also

[GSJohn]

Looks pretty close to this http://www.amazon.com/LOCKHART-CAFE-.../dp/B000GROHH4

[Bubba67]

Sorry meant to post this. Is this what you had in mind?

That's the Dunstall Cafe fairing, very close (and probably the one I'll end up getting). The one I'm looking for has a slanted screen rather than the bubble and note those cut-outs on the side for the turn signals.

Thanks for lookin' though.

[Bubba67]

Bubba I think that, unless i am wrong, is simply an Emgo, or Viper or whatever fairing you would find on Ebay or any other parts supplier that may call them a "cafe" fairing that has been cut down to the owners liking. They are made of ABS, so with a dremel you could go to town and come up with a pretty nice result. I had one of those fairings on my 1100G for a bit. The fairing itself was nice, but the windscreen that came with it was flimsy and developed stress cracks around the screws. Eventually i just snapped it off. I still have the fairing, and if you can find a windscreen to fit it, lemme know and you can have it for shipping cost. The windscreen shouldnt be too difficult to locate. It mounts easily, just with some L brackets that get bolted on to the headlamp ears. Orrr if you are in no hurry, I can use the one i have here to draw a mould from, and with some direction of what youd like, we could modify the mould and probably make one out of fibreglass in a relatively short amount of time. I have a buddy who is an expert glass man (does the body work for the Miss Budweiser hydrofoil/jetboat whatever) and we are in the design stages of starting a lil custom fiberglass biz that would revolve around making replica side covers for old UJMs (zooks to start with) so this would be another facet we could delve into .

TCK

If you had a pic of that fairing, that would be great.

A custom fairing would be sweet but I'm thinkin' low-dough and though I'm sure you guys wouldn't charge an arm and a leg for a fairing, I still couldn't justify the cost. Get that side cover biz going first before you start delving .

I can't believe how hard it is to find that exact fairing, or even close, on any of the big dealers sites .

Thanks

[doctorgonzo]

Almost identical to the $40.00 Emgo fairing on my bike... A guy on ebay sells them.

[Bubba67]

Looks pretty close to this http://www.amazon.com/LOCKHART-CAFE-.../dp/B000GROHH4

It is close and it is probably the one I will end up getting since this fairing seems impossible to find. Thanks.