Announcement

Collapse
No announcement yet.

Electrical Issues - A Couple of Questions

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Electrical Issues - A Couple of Questions

    So I finally got the 80GS550 engine back together, put some gas in the carbs, installed the battery, turn on the ignition, pull in the clutch, hit the start button and.......nothing. Put a screw driver across the solenoid posts..... nothing. I checked the voltage across the battery terminals 12.7V. Checked it across the cable connectors right at the terminals, 0V. Sanded off the cable connectors to shiny metal and reconnected the cables now I have 12+V across the connectors, so all good there (I should add that I was stunned that a little bit of build up on the connectors would completely wipe out conductance). Checked voltage at the solenoid and it was good as well.

    So I try again hit the start button and nothing. Put the screwdriver to the solenoid again and it cranks but shows no indication of trying to start. Test for spark and there was none so I figure I've got some electrical issues to figure out. Figured I would start with the start button since it is easier to hit the start button than using the screwdriver. I sanded down the contact surfaces on the button and nothing happened. So I measured the voltage at the kill switch and it was around 0.75V. Now I don't see anything in my manual that tells me what this voltage should be but I'm thinking it should be 12V.

    I should also add I measured voltage accross the battery and the crankcase and got 12+V, so that should indicated the ground connection there is good, right?

    So I go looking at the wiring schematic and the wires on the bike (man there are alot of them) and begin to feel a little overwhelmed. So my questions are, where should I start? And, what is the best way to actually clean the connections? Thanks in advance.
    Last edited by Guest; 12-11-2008, 11:18 AM. Reason: Additional Info

    #2
    If you put a screw driver across the solenoid posts and the solenoid is wired correctly then your starter is not getting current, either the starter is dirty or the solenoid is no good.

    Check your connections and make sure all bullet connector are cleaned and tight.

    Check to see with a test light that you have voltage to the swicth and from the switch to the solenoid trigger circuit ( the thinner wires on the solenoid ).

    Comment


      #3
      Pull you headlight bucket apart and check all the connections. I had a similar problem and the wire connections coming from the kill switch were loose and arcing. Reconnected, no further problems.

      Good luck! JOhn

      Comment


        #4
        Originally posted by glstine View Post
        So I finally got the 80GS550 engine back together, put some gas in the carbs, installed the battery, turn on the ignition, pull in the clutch, hit the start button and.......nothing. Put a screw driver across the solenoid posts..... nothing. I checked the voltage across the battery terminals 12.7V. Checked it across the cable connectors right at the terminals, 0V. Sanded off the cable connectors to shiny metal and reconnected the cables now I have 12+V across the connectors, so all good there (I should add that I was stunned that a little bit of build up on the connectors would completely wipe out conductance). Checked voltage at the solenoid and it was good as well.

        So I try again hit the start button and nothing. Put the screwdriver to the solenoid again and it cranks but shows no indication of trying to start. Test for spark and there was none so I figure I've got some electrical issues to figure out. Figured I would start with the start button since it is easier to hit the start button than using the screwdriver. I sanded down the contact surfaces on the button and nothing happened. So I measured the voltage at the kill switch and it was around 0.75V. Now I don't see anything in my manual that tells me what this voltage should be but I'm thinking it should be 12V.

        I should also add I measured voltage accross the battery and the crankcase and got 12+V, so that should indicated the ground connection there is good, right?

        So I go looking at the wiring schematic and the wires on the bike (man there are alot of them) and begin to feel a little overwhelmed. So my questions are, where should I start? And, what is the best way to actually clean the connections? Thanks in advance.
        To have your engine running is mandatory to have the appropriate fuel mixture and good working ignition system, so, following this;
        Make the following tests:
        First; Check your battery and cables voltage
        Second; With your circuit tester, check that your starter button completes a circuit.
        Third; Check electrical components plate ground connection, if you don't have a good ground connection install a cable directly to your battery negative post.
        Fourth; With your VOM or circuit tester check you are having voltage at coils terminals and as per your manual check your coils primary and secondary impedance.
        Fifth; Following your manual instructions make the required tests to your signal generator and your CDI; OR check the condition and voltage of your points.
        Sixth; Check all your harness connections concerning to your ignition system.
        Seventh; Check you are having fuel at your carburetors, if not check your fuel cock. One thing that works is to open the valve at reserve.

        Once you have both fuel and ignition your engine should start without any problem.
        GOOD LUCK

        Comment


          #5
          Thanks for the replies. I've already replaced the solenoid (had one I'd grabbed previously so I figured I would go ahead and put it on) and cleaned the battery connections so I guess I will just start at the fuse box and go from there.

          Is there a way to clean the larger plastic connectors or do I just want to make sure those are good and tight?

          Comment


            #6
            Is there a way to clean the larger plastic connectors or do I just want to make sure those are good and tight?
            CRC makes a product called QD electronics cleaner that works well to remove grease and grime from sensitive electronics. It is also safe on plastic. You should be able to get it at any autoparts store or Walmart.

            Another good product is DeoxIT from CAIG laboratories. They make products that clean and protect electrical connectors.

            Comment


              #7
              Clean the kill switch. Are you sure the clutch interlock switch if working?
              1983 GS 1100E w/ 1230 kit, .340 lift Web Cams, Ape heavy duty valve springs, 83 1100 head with 1.5mm oversized SS intake valves, 1150 crank, Vance and Hines 1150 SuperHub, Star Racing high volume oil pump gears, 36mm carebs Dynojet stage 3 jet kit, Posplayr's SSPB, Progressive rear shocks and fork springs, Dyna 2000, Dynatek green coils and Vance & Hines 4-1 exhaust.
              1985 GS1150ES stock with 85 Red E bodywork.

              Comment


                #8
                Well I started cleaning electrical contacts starting at the battery and to the fuse box which I cleaned to some degree (i'm going to go get some Deoxit today) and now get just a 1V loss to the kill switch. Messed around with the start switch some more and now it works. The clutch switch has apparently been disabled by the PO. Also going to get some spade connectors and start replacing the bullet connectors.

                Comment


                  #9
                  Don't forget to clean the main ground wire connection to the motor. It is also also a good idea to run the additional ground from the R/R to the battery. While you are picking up the contact cleaner also get some dielectric grease if you do not have it already and use it to re-assemble all connections that you clean up.

                  82 GS850L - The Original http://s224.photobucket.com/albums/d...ePics067-1.jpg
                  81 GS1000L - Brown County Hooligan http://s224.photobucket.com/albums/d...ivePics071.jpg
                  83 GS1100L - Super Slab Machine http://s224.photobucket.com/albums/d...t=DCP_1887.jpg
                  06 KLR650 - "The Clown Bike" :eek: http://s224.photobucket.com/albums/d...nt=SERally.jpg
                  AKA "Mr Awesome" ;)

                  Comment

                  Working...
                  X