Also, should I use red high strength locktite on these or will the heat of the engine going to burn that off?
Announcement
Collapse
No announcement yet.
adjustable cam sprocket bolt torque
Collapse
X
-
adjustable cam sprocket bolt torque
I have adjustable cam sprockets I will be putting on my set of webcams for my gs1000 engine. How tight should I torque the bolts down to? I obviously dont want the sprockets to shift postition on the cam. The stock torque on the bolts is 6-8 ft lbs for regular cam sprockets.
Also, should I use red high strength locktite on these or will the heat of the engine going to burn that off?Tags: None
-
jgordon
6.5 to 8.5 W/ red Locktight is perfect. Is this your first time for timing the cams?
It can make a big difference if you do it right!
-
Suzuki_Don
-
Originally posted by Tarbash 27 View PostI have adjustable cam sprockets I will be putting on my set of webcams for my gs1000 engine. How tight should I torque the bolts down to? I obviously dont want the sprockets to shift postition on the cam. The stock torque on the bolts is 6-8 ft lbs for regular cam sprockets.
Also, should I use red high strength locktite on these or will the heat of the engine going to burn that off?
The GS1000 & 750's 2V use allen head bolts to secure the cam sprockets & cams while the GS1100 & 750 4V use bolts. When I slotted my stock GS1000 cam sprockets back in the 1980's I used red loctite that had been date code expired and tightened the allen head bolts as tight as possible with a standard 5" long allen head wrench. Why, because as you have noticied the surface area under the cam sprocket bolts has been greatly reduced and you are no worried about the sprockets slipping. The Allen head bolt is only contacting cam sprockets along two small arcs vs. the stock 360 degrees. When I revisited cam timing again years later I needed a propane torch to break them free. I even dented the inner hex of the allen head's and I was praying I would get them out.
Rapidray & other drag racer's always use red locktite and sometimes tack weld that sprocket bolt in place so it does not move but I prefer easy servicing but then again I have a street bike. Last year I revisited cam timing again and replaced the stock GS Allen Head bolts with the following. Have a look, the flange head allen head bolt provides more surface area with the cam sprocket and does not interfere with the cam chain operation.
Steve
1979 GS1000E (45 Yrs), 1981 GPz550 (11 Yrs)
Comment
-
Tarbash 27
Well This is my first time timing cams. I did buy those better sprocket bolts from mcmaster carr. They are cut to the perfect length. I would like to keep these as tight as possible but dont want to strip them out. Since I will have to take the cams back out to do a valve adjustment, I could tack weld them, but I really dont want to just in case I have to fine tune them.
I will play with them tomorrow .
Comment
-
Sorry about the long winded response then Matt. You probably read the same threads because I recall Rapidray & Big Jay or someone talking about a V&H cam timing video, it would be great if they could provide a link to that process.
The biggest "challenge" I have found with degreeing cams is the 1" Dial Indicator stem is too fat to easily fit between the cam & bucket at max lift. If anything touches while rotating you have to start all over again. I unscrewed the knurled tip on the dial indicator and added a thin extension which made the process much easier. Good luck.Steve
1979 GS1000E (45 Yrs), 1981 GPz550 (11 Yrs)
Comment
-
jgordon
Originally posted by Suzuki_Don View PostDo you have any tips for us MR GORDON. On how to do it right that is.
Use a positive stop and a nice big degree wheel on the ignition side with a pointer. Make sure you're close to TDC looking at the timing mark. Rotate the engine back easy until it stops and read the degree wheel. Rotate the engine forward direction until it stops again and read the degree wheel. In the middle of those two numbers is TDC absolute.
Set the valves at the normal clearance and set up the dial indicator. Rotate the engine in the normal direction of rotation and watch the dial indicator until it hits 50 thousands. Write down that number. Rotate the engine again in the normal direction of rotation and when the dial indicator stops at the last 50 thousands before it zero's read it and write down the number.
Lobe center = Opening + closing + 180 / 2 - the smallest number.
Example
Opens at ...................30
Closes at ...................70
Plus .........................180
Total.........................280
Divided by 2...............140
Minus smallest number...30
Lobe Center...............110 degrees
I set the exhaust first and then the intake.
Hope this helps.
Comment
-
Suzuki_Don
That sounds great MR GORDON. I am gathering information for when I eventually get my cams back in. What is the best figure for the GSs. Would it be the same for the big motors and the small ones.
Comment
-
jgordon
Originally posted by Suzuki_Don View PostThat sounds great MR GORDON. I am gathering information for when I eventually get my cams back in. What is the best figure for the GSs. Would it be the same for the big motors and the small ones.
Depends on what you like. Top 110 ex./110 in. or Bottom 110 ex. /106 in.
You'll get different answers on all this.
You can call me Mr. Gordon ( not capped ) if you like (-:
Comment
-
Suzuki_Don
Originally posted by jgordon View PostDepends on what you like. Top 110 ex./110 in. or Bottom 110 ex. /106 in.
You'll get different answers on all this.
You can call me Mr. Gordon ( not capped ) if you like (-:Last edited by Guest; 02-09-2009, 11:02 PM.
Comment
-
Suzuki_Don
Originally posted by rapidray View PostJust so you know, a smaller # on the intake lobe center is ADVANCED, not retarded! Ray.
Thanks.
Comment
-
Originally posted by Suzuki_Don View PostThanks Ray. Is there a decent article around that takes you from go to whoa on doing the cam timing, lobe centre, thing for us that are comfortable working on engines but have not done this task before.
Thanks.
Didn't I provide you with a Pdf link to a "Degreeing Cam" article from Custom Rider Sept 1981? I thought I did bit I might be suffering from crs, so excuse me. Custom Rider (Off Shoot of Cycle Guide) wasn't around long but it was stuffed full of technical articles
I found this article on the Forum useful as well. Hope it helps
Steve
1979 GS1000E (45 Yrs), 1981 GPz550 (11 Yrs)
Comment
-
Suzuki_Don
Hi Thanks Super,
Yes that article does look familiar now. I think it is me going senile and getting forgetful. Thanks a lot.
Comment
-
jgordon
Originally posted by srsupertrap View PostSuzuki_Don,
Didn't I provide you with a Pdf link to a "Degreeing Cam" article from Custom Rider Sept 1981? I thought I did bit I might be suffering from crs, so excuse me. Custom Rider (Off Shoot of Cycle Guide) wasn't around long but it was stuffed full of technical articles
I found this article on the Forum useful as well. Hope it helps
http://medlem.spray.se/biker661/Camtiming.htm
Comment
Comment