repair for broken float post

[headsbikesmopars]

Anyone have a good repair for a broken float post ? I have heard of JB weld and drilling and threading also using a roll pin. Pot metal..didn't take much to break that thing off..!!!! Mine is broken right thru the center of the pin hole, right at the top. Not enough left to drill but it does fit back on there nicely. A good epxy that isn't affected by fuels might be all I need. The sad part is I was almost finished, having to adjust float level was all and now this delay....
thanks

Terry

[Larry D]

My #2 float post broke in the same place. I thought I had a pic, but I don't. Anyway, the way the float pin rests in the semi-circle hole works just fine, as long as the other side is intact. All the pin does is pivot the float and with the other post intact, it's not coming loose. I do keep my eye out for another set of 32mm carbs, but the bike runs great and I'm not worried about it.

[posplayr]

Did a little research this morn.

Seeing as how strong as this aluminum brazing is, U might not even need to center drill the post. One of my original ideas was to use a roll pin to hold the post into the carb body. U could still use the roll pin to hold the part in place, but this stuff is so strong it is probably not required.

Any epoxy will need 2-3 days to fully cure before allowing it to come in contact with gas. Epoxy will not have the strength this stuff does.

http://www.thegsresources.com/_forum/showthread.php?t=137952

Pos

[nisom512]

I had same problem with my carbs when I got hte bike home and then it wouldnt start any more so I took them apart and whala broken post so I went on Ebay and bought a new set for $50 Great deal. they are on my 550 now and I have used the original set for parts......

thats just my idea.

[SqDancerLynn1]

I would like to take a carb to one of those guys and see them repair it with that crap ?? aluminum weld ??

[almarconi]

I still don't understand how people break the posts off. A series of very light taps on the pin with a punch usually moves it enough to get pliers on it.

[headsbikesmopars]

Thanks everyone who posted. Larry has a good point. It can't really go anywhere once the bowl is installed. I talked to a local GSer friend today and he said he has done the same thing. My brother broke some on his GS550 also. Makes me wonder how many of these carbs have been broken over the years that Suzuki has been using the CV's. My Kawasaki Triples don't have a float pin that is press fit. It just slides in and the bowl when installed keeps it from moving. Simple and easy.

Terry

[Roemy24]

Gentlemen, I'm working on a permanent fix for this situation. I'm an applications engineer for a company that makes prototypes, who also has a material that is chemical/heat resistant. I'm experimenting right now and am practically done designing and building. I'll try to have better pictures posted tommorrow or Tues. Anyway, attached is a picture that is a few revisions old but you'll get the idea. The newer one encloses the top posts a little better. Fairly inexpensive also to build and ship.

[duaneage]

Use a .22 shell casing, cut it to size and fit it over the post. You can then drill a small hole for the pin. .22 magnum is longer and may work better

[Suzuki mad]

Gentlemen, I'm working on a permanent fix for this situation. I'm an applications engineer for a company that makes prototypes, who also has a material that is chemical/heat resistant. I'm experimenting right now and am practically done designing and building. I'll try to have better pictures posted tommorrow or Tues. Anyway, attached is a picture that is a few revisions old but you'll get the idea. The newer one encloses the top posts a little better. Fairly inexpensive also to build and ship.

Would the extra material inside the float bowl area cause an inballance in the ammount of fuel in the carb body and cause it to lean out or stop or limit the motorcycle before full rev's were attained?

[Billy Ricks]

When reistalling the pins I leave a little gap between the head of the pin and the post so I can get a screwdriver under the head and gently pry it back. The bowls won't allow the pin to back out.

[Nessism]

The post that snaps off is the one next to the nail head on the float pin. The pin is flared just under than nail head so it creates an interference fit to the post.

If you place a small socket on the work bench, and then center the nail head of the float pin over the socket before driving out the pin, it won't snap off.

[hcritz]

Hey Guys...
There is a guy on the soc4 forum (Honda CB) that does micro laser welding...he repairs a lot of the broken post for guys there...
I believe his Nic there is bigjim.
Here's a link to the web page.

http://www.sohc4.net/index.php?title=Main_Page

[hcritz]

Here is a link with picts of his work...

http://forums.sohc4.net/index.php?topic=18649.0

[duaneage]

Grab the big end with a small pair of wire cutters and pull it out, no tapping needed. This is the one thing in the carb rebuild document on this site that should be addressed. I broke a tower doing this first time and had to get a replacement body.