.png "Powered by vBulletin")
I just reassembled my carbs on my 79 GS850 and I thought I followed the directions to the letter. I have a piece that I am not sure where it is supposed to go. I have attached a picture. I haven't gotten to the part to put the carbs on the bike yet but I just did a manual sync for the sliders to go fully open and fully closed. Could someone please look at this pic and tell me what they think this piece is and where it goes? It's a little round cylinder tube. Some kind of sleeve? it's metal.
-
-
I've never seen anything like that on the VM22's or the VM29 smoothbore carbs. Are you sure it's from the carbs? Almost looks like brass. Do you know what kind of metal it is?Ed
To measure is to know.
Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182
Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846
Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf
KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection -
It's brass. To be honest a friend disassembled the carbs. It may not be from them but I just want to be sure. Where else do you think it would go?Comment
-
Hopefully someone more knowledgeable than me about the VM26's will chime in, but I've never seen a part like before.Ed
To measure is to know.
Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182
Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846
Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf
KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-ResurrectionComment
-
going out on a limb here .. but looks like the tube that goes betwix the carbs.to me but then i have no idea of what carbs you have .. or like wise..Comment
-
How about this part?
Like I said, I didn't take them apart and I am following the instructions on the article on bike cliffs site the best I can. Do these even go on the carbs?
Comment
-
Forgot to attach.Comment
-
That part holds the throttle shaft in place. Attaches with a screw to the main gang support.Originally posted by syren View Post
Edit: check this photo. I think it shows that second piece and where it is supposed to go.
Last edited by Nessism; 03-27-2009, 11:39 PM.Ed
To measure is to know.
Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182
Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846
Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf
KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-ResurrectionComment
-
Yes, that's where that second piece goes. There is a grove in the rod that the piece fits into and then screws to the post on the bracket.Originally posted by Nessism View PostThat part holds the throttle shaft in place. Attaches with a screw to the main gang support.
Edit: check this photo. I think it shows that second piece and where it is supposed to go.
I've rebuilt several sets of VM26's, and that first part does not look like anything I've seen. I don't think it belongs.85 GS1150E May '06 BOM
79 GS1000S Wes Cooley Beast
Comment
-
Ditto Bruce - the first part isn't from a set of VM26s.Originally posted by renobruce View Post79 GS1000S
79 GS1000S (another one)
80 GSX750
80 GS550
80 CB650 cafe racer
75 PC50 - the one with OHV and pedals...
75 TS100 - being ridden (suicidally) by my fatherComment
-
In case you needed a third opinion, I don't think that first piece is from a Mikuni VM either...Comment
Comment