Announcement

Collapse
No announcement yet.

gs1100g charging problem

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
    #1

    gs1100g charging problem

    ----my bike just quit one day--checked everything -finally tappe rectifier lightly with hammer--spark normalized but periodically will quit and bike will stall. Ordered new one in stops stalling but doesn't allow charging to happen. Old one does but will give out???? thankyou Bob
    Tags: None
    #2
    Do the stator papers
    404 Not Found
    http://www.thegsresources.com/gs_garage.htm

    You may have a bad stator, connections or battery.
    Who knows until you check.
    1983 GS 1100E w/ 1230 kit, .340 lift Web Cams, Ape heavy duty valve springs, 83 1100 head with 1.5mm oversized SS intake valves, 1150 crank, Vance and Hines 1150 SuperHub, Star Racing high volume oil pump gears, 36mm carebs Dynojet stage 3 jet kit, Posplayr's SSPB, Progressive rear shocks and fork springs, Dyna 2000, Dynatek green coils and Vance & Hines 4-1 exhaust.
    1985 GS1150ES stock with 85 Red E bodywork.

    Comment

      #3
      Greetings and Salutations!!

      Hi Mr. bwarnock,

      Here is your unofficial "mega-welcome". Please pay particular attention to the "Top 10 Common Issues", the Carb Rebuild Series, and the Stator Papers. As has been suggested, it's always a good idea to make sure all of the electrical connections and grounds on the entire bike (including fuse box and ignition switch) are clean and corrosion-free. Now let me roll out the welcome mat for you...

      Please click here for your mega-welcome, chock full of tips, suggestions, links to vendors, and other information. Then feel free to visit my little BikeCliff website where I've been collecting the wisdom of this generous community. Don't forget, we like pictures! Not you, your bike!

      Thanks for joining us. Keep us informed.

      Thank you for your indulgence,

      BassCliff

      Comment

        #4
        Old electrial connectors are way to commond on these old bikes. Check all connections for clean metal and tight fit. By tapping on it you may have caused the plug to make contact and then the contact was lost by ridding. Thats a good place to start good clean connectors, good luck.

        Comment

          #5
          gs1100g charging

          Thankyou for your help.

          I did separate wires leading to fuse box etc. and my cutting out problem is gone. Seems to be running just fine however when I did check my volts coming though to battery it showed around 12.4 when reving to 4000 rpm was around 12.8----at idle is around 12.0 ---other than that runs fine. Not sure if those numbers will sustain batter enough.

          thx Bob

          Comment

            #6
            Hi Mr. bwarnock,

            Those voltage numbers will probably not keep your battery charged. Go through the troubleshooting procedures in the Stator Papers to find out what is not working. Note that the Stator Papers specify starting with a known good battery when troubleshooting. You should be getting around 14.5v at the battery when revving around 4000-5000 rpm. Keep us informed.


            Thank you for your indulgence,

            BassCliff

            Comment

              #7
              Originally posted by bwarnock View Post
              Thankyou for your help.

              I did separate wires leading to fuse box etc. and my cutting out problem is gone. Seems to be running just fine however when I did check my volts coming though to battery it showed around 12.4 when reving to 4000 rpm was around 12.8----at idle is around 12.0 ---other than that runs fine. Not sure if those numbers will sustain batter enough.

              thx Bob

              No smoke is good, but sorry no cigar on those voltages

              Comment

              Previous template Next
              Working...
              X