Thanx so much....Anita
Announcement
Collapse
No announcement yet.
Air box question
Collapse
X
-
Krooozn
Air box question
I reinstalled the carbs today and when I was trying to tighten the clamps that hold the airbox to the carbs.....I began to notice that they wouldn't get tight enough to seal the carb to the box. They are made of a hard plastic type substance and no matter how much I tighten the clamps....it was still loose. So can anyone tell me if there is any sort of gasket/oring, etc that goes on the carb tubes to make the seal more airtight...or is this how it is suppose to be? I tried looking in my service manual, but struck out....
Thanx so much....AnitaTags: None
-
Forum LongTimerGSResource Superstar
Past Site Supporter
Super Site Supporter- Mar 2006
- 35622
- Torrance, CA
The airbox boots get hard with age and the clamps get stretched out when people over tighten them. There are also instances with Suzuki superceeded some clamp part numbers and messed up - the new clamps are too large. Not sure which applies in this case but the problem could be related to one of these. Good luck and hope this helps.Ed
To measure is to know.
Mikuni O-ring Kits For Sale...https://www.thegsresources.com/_foru...ts#post1703182
Top Newbie Mistakes thread...http://www.thegsresources.com/_forum...d.php?t=171846
Carb rebuild tutorial...https://gsarchive.bwringer.com/mtsac...d_Tutorial.pdf
KZ750E Rebuild Thread...http://www.thegsresources.com/_forum...0-Resurrection
-
Suzuki_Don
Anita it sounds like the rubber intake tubes that connect the airbox to the throat of the carbs has gone hard and will not squeeze down when the clamps are tightened.
These two parts are not that expensive for your bike. There is a left and right part as follows.
Part# 13881-44100 Desc OUTLET LH Price $11.48
Part# 13882-44100 Desc OUTLET RH Price $11.48
These details are from Alpha Sports so from another vendor they will be even cheaper than that.Last edited by Guest; 02-14-2010, 03:22 PM.
Comment
-
With bad clamps I've cut old clamps and put them underneith the stretched clamps.
Or just buy new ones and new boots.1983 GS 1100E w/ 1230 kit, .340 lift Web Cams, Ape heavy duty valve springs, 83 1100 head with 1.5mm oversized SS intake valves, 1150 crank, Vance and Hines 1150 SuperHub, Star Racing high volume oil pump gears, 36mm carebs Dynojet stage 3 jet kit, Posplayr's SSPB, Progressive rear shocks and fork springs, Dyna 2000, Dynatek green coils and Vance & Hines 4-1 exhaust.
1985 GS1150ES stock with 85 Red E bodywork.
Comment
-
Forum LongTimerBard Award Winner
GSResource Superstar
Past Site Supporter
Super Site Supporter- Oct 2003
- 17441
- Indianapolis
They're actually a soft rubber. Since you referred to them as "hard plastic" I'm guessing that you simply need new airbox to carb boots.1983 GS850G, Cosmos Blue.
2005 KLR685, Aztec Pink - Turd II.3, the ReReReTurdening
2015 Yamaha FJ-09, Magma Red Power Corrupts...
Eat more venison.
Please provide details. The GSR Hive Mind is nearly omniscient, but not yet clairvoyant.
Celeriter equita, converteque saepe.
SUPPORT THIS SITE! DONATE TODAY!
Co-host of "The Riding Obsession" sport-touring motorcycling podcast at tro.bike!
Comment
-
Krooozn
Thanx to all who responded to my question....I have just ordered new boots and clamps from BikeBandit.com.....their prices were really good.....I also ordered new air filters for the bike as well....as that was something on my need list.....getting one-piece at a time closer to starting my bike!
Thanx again to all.....Anita
Comment
-
Originally posted by Krooozn View Post....I have just ordered new boots and clamps from BikeBandit.com.....their prices were really good.....
Actually, it's not hard to do, but you can still do better than Bike Bandit.
Prices for your airbox boots:
Alpha $11.48
Bike Bandit $9.57
Cycle Parts Nation $7.27
Many other suppliers on the list, but they tend to lie between BB and CPN.
.sigpic
mine: 2000 Honda GoldWing GL1500SE and 1980 GS850G'K' "Junior"
hers: 1982 GS850GL - "Angel" and 1969 Suzuki T250 Scrambler
#1 son: 1986 Yamaha Venture Royale 1300 and 1982 GS650GL "Rat Bagger"
#2 son: 1980 GS1000G
Family Portrait
Siblings and Spouses
Mom's first ride
Want a copy of my valve adjust spreadsheet for your 2-valve per cylinder engine? Send me an e-mail request (not a PM)
(Click on my username in the upper-left corner for e-mail info.)
Comment
Comment