Yeah actually I was thinking about one of the standard crank models.
Announcement
Collapse
No announcement yet.
how do i get my bike into a pickup??
Collapse
X
-
Clone
I use a piece of C-channel and back my truck up to the curb. then either push it up or drive it on, the angle isn't so bad and the tires sit in the channel and don't come out the sides easily. 8)
Comment
-
lartross
-
Pete Logan
For riding in to my trailer, I use three ramps. One for the bike and a lighter ramp on each side for dabbing feet. Those foot ramps have saved mine a couple times
I also screw a piece of channel alongside the tires on each side. If you have a ribbed bed in the truck that may be just as good. If you don't want to screw into the truck bed, throw a piece of shuttering cut to size in the back and screw into that. I don't use any stand, and tie down with ratchet straps fore and aft on each side.
So far no problems on the road.
Pete
Comment
-
Morgan
For riding in to my trailer, I use three ramps. One for the bike and a lighter ramp on each side for dabbing feet. Those foot ramps have saved mine a couple times
-Morgan
Comment
-
I don't really know if any one technique is better than any other, but this is how I generally load a bike into the back of a van. The loading area height is generally about the same as that as the bed of a pickup, so, it should work with either vehicle.
>>>>Press Here<<<<Frosty (falsely accused of "Thread-Hijacking"!)
"Make it idiot proof and someone will make a better idiot."
Owner of:
1982 GS1100E
1995 Triumph Daytona 1200
Comment
-
Forum LongTimerCharter Member
GSResource Superstar
Past Site Supporter- May 2002
- 19251
- Toronto, Canada
[quote="dpep"][Talk about a Freudian slip!! Good eye, Ron.
Yeah actually I was thinking about one of the standard crank models.[/quote]
I understand they can be REALLY easy to find, Don. Many men wake up to one every morning :roll: :roll:Bertrand Russell: 'Men are born ignorant, not stupid. They are made stupid by education.'
Comment
-
wrench
[quote="argonsagas"]Originally posted by dpep[Talk about a Freudian slip!! Good eye, Ron.
Yeah actually I was thinking about one of the standard crank models.[/quote]
I understand they can be REALLY easy to find, Don. Many men wake up to one every morning :roll: :roll:
John.
Comment
-
Pete Logan
Originally posted by MorganFor riding in to my trailer, I use three ramps. One for the bike and a lighter ramp on each side for dabbing feet. Those foot ramps have saved mine a couple times
-Morgan
Originally posted by frosty5011I don't really know if any one technique is better than any other, but this is how I generally load a bike into the back of a van. The loading area height is generally about the same as that as the bed of a pickup, so, it should work with either vehicle.
Pete
Comment
-
Hoomgar
My 78 GS1000 has been lifted in and out of pickups on several occations by two people. Front wheel first. Then both on the back making sure you lift it high enough before sliding it in so as not to drag the bottom.
I am not recommending this as I am very large and strong as well as my friends and family members but I am thinking that if two of us do it often with little effort then people of smaller stature should be able to do it with 3 or 4 people. It's quite easy.
I like to put my bike on it's side stand then and push it diagnally into the bed. Front wheel cut the whole way left and tucked tight into the corner behind the driver and the rear wheel pulled over against the right side of the bed. Then a tight rope from the top tripple tree clamp area to the corner of the bed is all that is really needed to secure it for even the longest journeys. More rope is always better but if you tie ropes off to the right them you only want them snug, not tight.
Doing it this way I have been able to drive normally giving almost not thought at all to the bike in the back. many a bike has made the trip with my in this fassion. Both street and dirt bikes a like.
Hope that helped. I know it was a late post. Sorry
Comment
-
Anonymous
-
Hoomgar
-
Anonymous
-
Not that my method adds any info to all these posts, but here goes:
I have a 10' 2x12 with some metal ramp-ends bolted on (overpriced at big hardware stores). I back my truck across the street to my neighbors driveway, which is steep where it meets the street. Push or drive the bike to his driveway and wheel it onto the truck - the ramp is almost level and I can do it alone. Then I put the sidestand down and hook a tiedown to each eye-bolt on the sides of the front of the bed and hook then to the handlebars. Then I get on the bike, lean forward and bounce my considerable weight to compress the forks, at the same time tightening the tiedowns - alternating left to right. Solid as a rock."When I give food to the poor, they call me a saint. When I ask why they are poor, they call me a communist." Bishop Helder Camara
"Beware of the man with only one gun. He probably knows how to use it."
http://i13.photobucket.com/albums/a2...dStatesMap.jpg
82 GS1100E....black w/WC fairing and plenty o corrosion and low levels of attention
Comment
-
Pete Logan
Originally posted by Bert PattersonNot that my method adds any info to all these posts
Pete
Comment
Comment