• Required reading for all forum users!!!

    Welcome!
    Register to access the full functionality of the GSResources forum. Until you register and activate your account you will not have full forum access, nor will you be able to post or reply to messages.

    A note to new registrants...
    All new forum registrations must be activated via email before you have full access to the forum.

    A Special Note about Email accounts!
    DO NOT SIGN UP USING hotmail, outlook, gmx, sbcglobal, att, bellsouth or email.com. They delete our forum signup emails.

    A note to old forum members...
    I receive numerous requests from people who can no longer log in because their accounts were deleted. As mentioned in the forum FAQ, user accounts are deleted if you haven't logged in for the past 6 months. If you can't log in, then create a new forum account. If you don't get an error message, then check your email account for an activation message. If you get a message stating that the email address is already in use, then your account still exists so follow the instructions in the forum FAQ for resetting your password.

    Have you forgotten your password or have a new email address? Then read the forum FAQ for details on how to reset it.

    Any email requests for "can't log in anymore" problems or "lost my password" problems will be deleted. Read the forum FAQ and follow the instructions there - that's what we have one for...

  • Returning Visitors

    If you are a returning visitor who never received your confirmation email, then odds are your email provider is blockinig emails from our server. The only thing that can be done to get around this is you will have to try creating another forum account using an email address from another domain.

    If you are a returning visitor to the forum and can't log in using your old forum name and password but used to be able to then chances are your account is deleted. Purges of the databases are done regularly. You will have to create a new forum account and you should be all set.

fried fuse

  • Thread starter Thread starter Anonymous
  • Start date Start date
A

Anonymous

Guest
I went to hook up something, pulled the fuse cover off and the MAIN was melted into the box, but bike still runs, 82gs11e???
 
Meltdown!!!!!!

Meltdown!!!!!!

Bost:
OK..first you need to disassemble the box(battery disconnected first of course) keep track of which wires go where(write it out with illustrations that you can decipher) the trick is to pick apart the melted sections to get to the fuse itself.Once you get to the fuse you will probably notice the fuse is intact but is of a rating way too high eg.30 amp as opposed to the 10 amp.Depending on the damage you may have to get a replacement single seperate fuseholder & reuse the box for all the other fuses.If the rating of the suspect fuse is correct you have some poor connections which WILL make for a heat buildup.If the damage is too much you really should consider getting a whole new box.It really should'nt be too much $$.
By the way what were you "hooking up" that may have caused this & why?
Rick....
Ps: if you do get a replacement box you can make sure of good connections
 
thanks Rich, i was hooking up an accessory plug for cell ect, took off helmet lock and used the fixture by shock, took off cover to use screw posts for plug and noticed the melted plastic, and the 20amp fuse, thank you for the help
 
A bad/dirty connection on the fuse will also cause the fuse to get hot and melt the fuse holder
 
If you switch the fuse box you'll need one that takes 2 power inputs. Atleast my 1100 needs this and it's older than yours. One is for fuses that always have power on, the other is for fuses that are switched by the key.

Steve
 
I had the same problem, the entire box melted. I replaced the entire fuse holder with a fuse block bought at an electronics store. The reason the block melted was too much resistance on the wires due to poor electrical connections. Make sure all your connections are clean, tight and wiring is soldered to the fuse block not just connected with spade connectors.
 
Michael Falke said:
I had the same problem, the entire box melted. I replaced the entire fuse holder with a fuse block bought at an electronics store. The reason the block melted was too much resistance on the wires due to poor electrical connections. Make sure all your connections are clean, tight and wiring is soldered to the fuse block not just connected with spade connectors.
Click to expand...

Second that! Bad connections anywhere on the bike can lead to exactally what Michael said. I know this first hand! Clean them all up good when you get a chance. Take a weekend and go connection hunting and make sure they are all good connections everywhere you can. This is mostly true of an older bike but can happen on a newer one as well if there is early corosion.
 
If you're going to clean the electrical connections then don't forget the ground wires. If the connection on the fuse panel gets bad enough it could fry the regulator/rectifier. Better yet, mount it directly to the frame.
 
You must log in or register to reply here.
Back
Top