Twinpot Brake upgrade on 78 Skunk

[Chuck78]

So, even if the surface area of both designs is the same...square inch wise...the stopping power is greater with the elongated pads verses the circle style? Ya lost me in the applied psychics.... but I do have to agree that the circle style brake pad isn't really used anymore....might be a reason for that.

yes, correct. all of the surface area of the elongated pads is working on the larger effective rotor diameter area, whereas the round pads, half of the pad is effectively working on a much smaller diameter rotor, therefore has the effect of a much smaller diameter brake. factor in on top of that upgrading the front from 275 duals up to 296 duals, and it is very easy to see why this is a substantial braking upgrade!

[tkent02]

Haha - I've done that too... In the year plus that I ran these wheels not one person noticed.

I had one large diameter front brake and one small one for a year, and one was solid one was drilled. Can't even remember what was on the rear.
No one notices things like that unless your in a bike show or something.

[80GS850GBob]

Chuck78- that does make sense!

tkent02- {chuckle}we must be different here then, we always scrutinize each others cycles...looks/speed/mods.....

[tkent02]

Sorry, missed it. I was busy the last few days cleaning the garage.

[CrazyCloud]

I used Honda GL 1500 Valkyrie rotors for mine (1997-2003). They are nice because the bolt pattern is the same as stock, just need to enlarge holes to 8mm. They are a 296mm rotor. Also, the inner part of the rotors are Aluminum, so they drill very easily. They are a little different look than the CBR rotors, I like 'em. All clearances were fine with Salty's kit.

[80GS850GBob]

CrazyCloud, now that's different, and in a good way!

[steve murdoch]

Jason can you post a pic of the whole bike showing the new set-up.
Very different look.

[CrazyCloud]

Full shot for you Steve. I'll try to replace it with a better one when I get a chance.

[steve murdoch]

That pic works fine.
Dual disc spoke wheels are my favourite look. I think those rotors look great.

[CrazyCloud]

Thanks, I wasn't sure how they would look but I think they gave it some class!

[salty_monk]

A bit more traditional looking than the CBR ones. A good option to have

[80GS850GBob]

I gotta ask...what's the braking difference between the different sized twin pot calipers that everyone is using and the matched hole calipers?
Salty knows where this is going....along the way of procuring parts for my twin pot upgrade, my 07 Kawi EX650 MC came with it's matching calipers - which happen to be the same sized hole type. I'm told those aren't the ones of choice.....I get that....but it's my usual curiosity that makes me ask why this is?...why is the big and lil holed version so much better?

[Chuck78]

what's the braking difference between the different sized twin pot calipers that everyone is using and the matched hole calipers?

my 07 Kawi EX650 MC came with it's matching calipers - which happen to be the same sized hole type. I'm told those aren't the ones of choice.

but it's my usual curiosity that makes me ask why this is?...why is the big and lil holed version so much better?

is that a typo and you meant master cylinder bores?if your caliper setup does not properly match your master cylinder, you will have either a very spongy lever feel since you need to be moving twice as much fluid as you are, or a very hard lever feel.

EDIT - Ahhh I see... your wording and terminology were confusing. I looked up those calipers. That year has similar calipers to the ones we use, but non-universal L and seperate R caliper brackets without the matching holes on top and bottom on the universal L or R brackets

Also, more likely what you are referring to is that both of the pistons are the larger diameter, unlike the ones with the "universal L &/or R" bracket that have a smaller piston and a larger piston in each caliper. The pads look nearly the same. That would be excellent if those calipers would also work with dan's brackets as well. They appear to have a steel bracket still, so they could also be chopped up and welded onto as I did on mine.

I am guessing that with a smaller&larger piston, you may get a little bit of brake shoe toe-in to avoid squeal/noise, but causing a little more uneven pad wear. with a larger piston pair in each caliper, I am speculating that if the master cylinder bore is the same as with the older style, then you will get more power out of the caliper but a softer lever feel with more lever travel needed to reach full braking. basically you would have easier effort on the lever, but more travel of the lever needed. So you would have more powerful brakes, but your lever would come back further. I suppose they could change the geometry of the lever and the leverage it exerts to alter that as well. Lots of variables here.

[80GS850GBob]

Chuck, No, what I'm talking about is the 2 different types of twin pot calipers- the ones folks here are using, are the big and small piston version - while the other type is the matched sized piston twin pots. Lacking a pick Id say the one type in question would be the oem matched sized piston, twin pot calipers of an 07 Kawi EX650A7f.
Using CrazyClouds last posted pick- that type of twin pot caliper has the big piston hole on top and a lil one on the bottom- twin pot, but two different sized pistons.....the ones on an 07 Kawi EX650A7f have both pistons the same size....hope that helps explain my end of it.

Edit- yeah, sometimes it's hard to convey things from my head to the web...or others. Wasn't trying to talk down to you or anything.

[salty_monk]

"Feel" at the lever and less likely to squeal. The pads tend to wear even regardless in my experience. I believe the main reason they probably changed is for cost reasons. Less material & less SKU's, less material in the pad & a slightly easier pad swap (which helps dealer margins). They have one less piston & one less size O ring to stock.

I have ridden a couple of bikes with those later brakes fitted. Similar in every way. The bracket does not suit our purposes as well & they don't work with that bracket. Eventually I will look at them as an alternative when it becomes impossible to get good calipers but haven't had a chance as yet other than to have a quick look and see that it will be a 4 bolt bracket & will be more complex than what we currently have. (Read MORE EXPENSIVE )