Announcement

Collapse
No announcement yet.

1982 1100E 530 Chain Conversion Thread

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Turtleface
    Guest replied
    Well, everything's bolted up and seems to be ok. The installation process is pretty much the reverse of the disassembly, with the only exception being the front sprocket.



    Here's what we start with, no sprocket.



    Sprocket goes on first.



    Then the 6 mm spacer goes on.



    Lastly, the sprocket nut and the splined washer goes on, washer underneath the nut, of course. At this point in time, you can't tighten the nut, since you can't stop the sprocket from turning, so leave it be for the moment,

    Leave a comment:


  • rapidray
    replied
    Looking VERY nice!!! Ray.

    Leave a comment:


  • Shin-Ken 1074
    replied
    Hi Turtleface, good looking project you have started with the 530 chain. I run the 630 on my 1100 and at one time I was tempted to do the change over to the 530 set-up however, I just like the look of the 630 to much and couldn't go through with it. As you discovered there are fewer bike shops carrying the 630 these days and the ones that do seem to charge well for them.


    Thread hijack here to offer help to other 630 chain users.

    To fix my chain replacement problem I found an industrial chain supplier that imports Japanese made 630 O-Ring chain and will sell me the 96 links I need for about half the price the bike shops charge (well that was when I bought the last chain four years ago). Maybe this is a solution to anyone having problems finding 630 chain or paying what seems to be a high price for it. Iam very happy with the chain quality and after 40.000 km on it all is well, cheers.
    Last edited by Shin-Ken 1074; 12-13-2009, 05:51 PM.

    Leave a comment:


  • Mysuzyq
    replied
    +1, nicely done....your documentation would make even Posplayr proud!
    You should notice a difference with better response immediately, with the lighter set-up.....I did, even going the other way with gearing (taller, for a 'less busy' feel, on the highway).
    Tony.

    Leave a comment:


  • Turtleface
    Guest replied
    Originally posted by mighty13d View Post
    did you say something other than ''bike pron?" I mean holy crap that swinger cleaned up nicely. Kind of like taking the glasses off the nerdy girl in high school, slapping some heels and a nice dress on her and she's the queen of the prom! hahah nice write up. Probably could have used a pic of the wooden block positioned in there and one of a ''before chain removal, but after sprocket cover is off'' but otherwise I would give you an A+!

    VERY GOOD JOB!! maybe BassCliff can add this to his collection if it's not there already?????
    Thanks! Still have to fit it all together, I'll have to use the block trick to tighten down the front sprocket nut, I'll make sure to get a shot of it then. If this little write-up is well received, I'll continue with my plans to do more of them. I still need to clean carbs, refresh front forks, rebuild the brake system, install stainless lines, install my Progressive rear shocks and fork springs (thanks again, PO!) and the list goes on and on and on...And that's just to get it back to near stock condition. I say near stock, because any part I replace invariably has a better than stock option that usually turns out to be cheaper than the stock option, so I usually go the better than stock route.

    Leave a comment:


  • mighty13d
    Guest replied
    did you say something other than ''bike pron?" I mean holy crap that swinger cleaned up nicely. Kind of like taking the glasses off the nerdy girl in high school, slapping some heels and a nice dress on her and she's the queen of the prom! hahah nice write up. Probably could have used a pic of the wooden block positioned in there and one of a ''before chain removal, but after sprocket cover is off'' but otherwise I would give you an A+!

    VERY GOOD JOB!! maybe BassCliff can add this to his collection if it's not there already?????

    Leave a comment:


  • Turtleface
    Guest replied
    And here's the new parts.



    After I run over to a friends house to borrow his torque wrench, tomorrow's plan is to lube all the rear axle bits with a moly-fortified multi-purpose grease, and bolt everything back together. Loctite for all the sprocket, brake, and axle hardware. The hold downs for the adjuster blocks will probably get a little as well. Then I'll just have to install the new chain, install the masterlink, and adjust wheel alignment and chain slack. I'm pretty sure I've been riding on a trashed chain from the start, and if the bike was that much fun with a bad chain, I can only imagine what a new one will be like. And lighter than stock, and a quicker gear ratio as well. Today went pretty well, here's to hoping tomorrow will as well.

    Might as well post the limit of pictures, so here's some more pics of cleaned parts. Shiny!

    I know you guys are suckers for swing-arms, so here's a good one.



    Towards the rear, and a little closer.



    And here's how she sits now.

    Leave a comment:


  • Turtleface
    Guest replied
    Here's the rear wheel assembly before cleaning.



    Here's the rear sprocket and carrier before cleaning.



    And just the carrier.



    Here's how they look clean, and the new sprocket.

    Leave a comment:


  • Turtleface
    Guest replied
    Here are the paint sticks in holding the pistons apart.



    I tied the caliper to the frame with picture hanging wire, I wrapped the wire with black electrical tape where it contacted the frame, to prevent damage.

    After the caliper's off, remove the cotter pin holding the rear axle. Remove the nut on the end of the axle, a screwdriver through the hole in the axle on the opposite side will help, and then the whole axle and wheel assembly should pull out from the swingarm. I took the opportunity to clean the swingarm, and the axle spacers and axle. I cleaned up the sprocket carrier as well, and all the hardware.

    Here's the rear axle assembly, with spacers!



    And here's what the same parts look after a quick bath, and reinstalled on the cleaned swingarm.



    Just throwing everything back together so I don't lose anything. Here's a shot of the front sprocket cover area after a good cleaning.



    Got the vast majority of gunk off, there's still some in the harder to get to crevices. The rest will have to wait until I pull the engine next year for paint. I'm probably going to have everything soda blasted during prep.

    Leave a comment:


  • Turtleface
    Guest replied


    Next, I unbolted the bolt on the top of the swingarm, the one holding the adjuster blocks in place.



    Back off the lock nut, and remove the adjuster bolt far enough to swing the adjuster down out of the way.



    Remove the adjuster block. Repeat for the other side. At this point in time, I chased all the threads in the both of the adjuster assemblies. There was surface rust on mine, and this cleaned them up nicely. Action is now nice and smooth, everything turns well without any sort of binding.



    Remove the cotter pin on the castle nut, the castle nut, and the two bolts holding on the caliper. I slide the caliper onto a pair of Home Depot paint sticks at were approximately the same thickness as the rotor. Hopefully this keep the pistons pushed in, eliminating the need for brake bleeding later.

    Leave a comment:


  • Turtleface
    Guest replied
    Progress So Far

    Well, it's been a full day, that's for sure. Now that I've figured out how everything works, this seems like a pretty simple task, all in all. I've gotten everything apart and clean. Ready for it all to go back together tomorrow. I recently received a free center stand for my bike, from the PO, and recommend one to anyone who doesn't have one. It sure makes this procedure a breeze. The biggest problem I ran into was finding the motivation to scrub, scrub, scrub, scrub and scrub some more. Cleaning was the biggest time consumer today. Here's how I progressed:



    Started by removing this bolt, and pulling the shift linkage off the shaft.



    Next, these six bolts come out. They're all different lengths, so I just kept them in the sprocket cover, or threaded into their holes, to remember where each one went.



    Here's what my front sprocket area looked like when I pulled the cover. Gross! The red stuff seems like a mixture of dirt and chain-lube. Looks like a rusty mess, but it's all just gunk. You can see the build up right above the bottom bolts. That stuff had to be chiseled out with a screwdriver.



    Remove these two bolts and get the chain guard out of the way. Now's a great time to clean it up, while you have it off. At this point in time, I ran a piece of 1x2 pine through the rear wheel, and situated it so that it braced the wheel against the swing arm so I could remove the front sprocket nut. After that, I cut the dead chain off with an angle grinder.

    Leave a comment:


  • Turtleface
    Guest replied
    Originally posted by katman View Post
    that's the correct way dude. Make sure you put the locking washer between the spacer and the nut.

    If you take the shaft bushing off you will see it fits inside the indide of the stock sprocket outer damper. the hole is larger on the inside.
    Ok, I see how that works now. Thanks a ton. I'm glad I planned on this being a few days project, instead of trying to knock it out in a few hours. Gives me time to consult the Resources. Once I've got everything cleaned, re-lubed, and re-torqued, I'll post pics of the entire process, probably sometime tomorrow night. We'll have ourselves a nice pictorial tutorial for everyone else to follow.

    Leave a comment:


  • Guest
    Guest replied
    Originally posted by Turtleface View Post
    Here's the other way
    that's the correct way dude. Make sure you put the locking washer between the spacer and the nut.

    If you take the shaft bushing off you will see it fits inside the indide of the stock sprocket outer damper. the hole is larger on the inside.
    Last edited by Guest; 12-12-2009, 04:41 PM.

    Leave a comment:


  • Turtleface
    Guest replied
    Here's the other way

    Leave a comment:


  • Turtleface
    Guest replied
    Katman, you're not talking about the number 48 piece in that fiche are you? The spacer I'm talking about isn't listed in either of the pictures you posted.

    Here's a picture of the stock pieces I took off:


    Here's a picture of the new sprocket


    Here's a picture of the spacer I'm confused about


    Here's one way I could put these pieces on

    Leave a comment:

Working...
X