Announcement

Collapse
No announcement yet.

BUILDING AN I.C.B.M. KATANA 1100

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    #76
    how long have you been running that engine?

    you may have just saved me 700 bucks...Canadian that is.
    KATANA CUSTOMS/TECH

    Instagram: @rjmedia.tech, Updated more often, even from the events

    Comment


      #77
      PMFR WEBSITE HAS BEEN HACKED.



      anyone having the edress give them a shout and let them know.
      KATANA CUSTOMS/TECH

      Instagram: @rjmedia.tech, Updated more often, even from the events

      Comment


        #78
        Last year it was a stock engine and I had about 250 runs last year and my best time was 7.18 in the 1/8. But in Dec I put in the 1166 13-1 pistons, g4 cams, 38mm cv carbs, air shifter and made about 80 runs this year untill 2 months ago I installed the 7" slick and 5/8 offset sprocket and made about 39 runs. This month I installed the wheelie bars and made 11 runs before cracking the mount. So I got over 50 runs on the 5/8 off set and no problems..........yet.

        The day you install some wheelie bars is when you'll start breaking something 8O

        If you ride normal with just a few outburst's from time to time you should be OK. Or you can just go with a stronger output shaft, GS Zone has one for about $300, still alittle pricey
        1166cc 1/8 ET 6.09@111.88
        1166cc on NOS, 1/8 ET 5.70@122.85
        1395cc 1/8 ET 6.0051@114.39
        1395cc on NOS, 1/8 ET 5.71@113.98 "With a broken wrist pin too"
        01 Sporty 1/8 ET 7.70@92.28, 1/4 ET 12.03@111.82

        Comment


          #79
          Last year it was a stock engine and I had about 250 runs last year and my best time was 7.18 in the 1/8. But in Dec I put in the 1166 13-1 pistons, g4 cams, 38mm cv carbs, air shifter and made about 80 runs this year untill 2 months ago I installed the 7" slick and 5/8 offset sprocket and made about 39 runs. This month I installed the wheelie bars and made 11 runs before cracking the mount. So I got over 50 runs on the 5/8 off set and no problems..........yet.

          The day you install some wheelie bars is when you'll start breaking something
          Jake, thanks for the info. I have a 5/8 offset sprocket on mine and have been a bit worried about not having the support. This calms the fears a bit as it's going to be street driven.

          Comment


            #80
            OK Jake,

            So according to my calc. you have run that engine about 350 seconds or 5.83 minutes?? with no problems.......lol

            I think I will get the support bearing. ahahahah

            katman
            KATANA CUSTOMS/TECH

            Instagram: @rjmedia.tech, Updated more often, even from the events

            Comment


              #81
              Swanny,

              how long has yours held together?
              KATANA CUSTOMS/TECH

              Instagram: @rjmedia.tech, Updated more often, even from the events

              Comment


                #82
                Originally posted by katman
                OK Jake,

                So according to my calc. you have run that engine about 350 seconds or 5.83 minutes?? with no problems.......lol

                I think I will get the support bearing. ahahahah

                katman
                Well I would stay on the gas longer but I seem to run out of track and my bike does'nt make a very good dirt bike with that slick.

                Plus don't forget my burnouts are longer than my run's so that should at least double my time, say 12 minutes.
                1166cc 1/8 ET 6.09@111.88
                1166cc on NOS, 1/8 ET 5.70@122.85
                1395cc 1/8 ET 6.0051@114.39
                1395cc on NOS, 1/8 ET 5.71@113.98 "With a broken wrist pin too"
                01 Sporty 1/8 ET 7.70@92.28, 1/4 ET 12.03@111.82

                Comment


                  #83
                  Here is my latest version I think I like better. Or I can keep everyone guessing with this one?

                  KATANA CUSTOMS/TECH

                  Instagram: @rjmedia.tech, Updated more often, even from the events

                  Comment


                    #84
                    late your bike is amazing!!! if u wouldnt mind could u post some details like your frame , swingarm , wheeles , plastics , etc.. thanks

                    Comment


                      #85
                      I counted 380 passes. At 7 seconds average ballpark figure that would be 2660 seconds plus burnouts. Am I missing something here, is my math that bad?

                      Comment


                        #86
                        Only 50 of those passes were with the 5/8 offset cog....................

                        read carefully.
                        KATANA CUSTOMS/TECH

                        Instagram: @rjmedia.tech, Updated more often, even from the events

                        Comment


                          #87
                          Only 50 of those passes were with the 5/8 offset cog....................

                          read carefully.

                          is that your bike?
                          KATANA CUSTOMS/TECH

                          Instagram: @rjmedia.tech, Updated more often, even from the events

                          Comment


                            #88
                            Only 50 of those passes were with the 5/8 offset cog....................

                            read carefully.

                            is that your bike?
                            KATANA CUSTOMS/TECH

                            Instagram: @rjmedia.tech, Updated more often, even from the events

                            Comment


                              #89
                              Swanny,

                              how long has yours held together?
                              It isn't running yet.

                              Comment


                                #90
                                I called PMFR today and told them their site has been compromized so they are looking into it. I also ordered the 5/8 outboard support kit while I was on the phone in a fit of impulsive buying.

                                Help I am in Deeeeep. and getting deeper. I feel like buddy on "The Abiss" but the first twist of the whick and it will be all worth it.
                                KATANA CUSTOMS/TECH

                                Instagram: @rjmedia.tech, Updated more often, even from the events

                                Comment

                                Working...
                                X