1230

[chef1366]

Ah, another "L" back on the road. Kind of brings a tear to my eye. You da man Chef.

Shoot, I rode it there!

[jwhelan65]

Ah, another "L" back on the road. Kind of brings a tear to my eye. You da man Chef.

Possibly the worlds fastest "L" back on the road..

[chef1366]

Pretty much done
I had a nine mile Dyna 2000. I put the oil seal in cockeyed and ruined the trigger and rotor. Had to change ignition on the side of a highway. Good times.
Set the full advance with a degree wheel to 32 degrees on both coils.
Retourqed the head and checked the valve clearance.
Soldered the stator wires and cleaned up the rats nest of wires.
Installed a oil temperature guage (thanks Jim!)
Put on a new chain guard (thanks Scott!)
Plugs were clean and pretty white so I raised the needle one notch
In the carbs running 155 mikuni mains/50 pilot jets/DJ needle second notch from bottom
Degreed cams 108/108
Thanks to Kris V for use of his shop and hours of help. You the man!!
Raymond (Quicksilver Ray) for getting me a great deal on the Wiseco 1229 kit, trading me for the 1150 crank, the valve job and all the good advice.

http://s2.photobucket.com/albums/y32/chef1366/1229/

[gearhead13]

Lookin sweet!

[chef1366]

Lookin sweet!

You're next!
A bumpy road to completion but the sweet taste of victory!

[BassCliff]

Good going Bill. Just in time for some good summer riding.


All the best to you and yours,

Cliff

[gearhead13]

Isnt it always summer in Calif?
I pulled my engine out today, took about 3 hours or so. Hopefully i can get the 1170 kit for it.
I maxed out my torque wrench (140#) taking off the front spocket, a little too tight eh? A source of my noise maybe.

[chef1366]

Isnt it always summer in Calif?

Nah, it rains a couple of days a year.

[jwhelan65]

Great job Bill!

[chef1366]

Now it's jetting time.
Started with
155 Mikuni mains
50 Pilot jets
Needle on second from bottom
Plugs sooty with no heat color on threads
Now
152.5 Main
50 Pilot
Needle two and a half from bottom
This is a very safe jet with good color on the plugs and a half to one thread of heat.
I'll stick with this until the motor breaks in. The first jetting would inhibit the engine from breaking in with the rich settings.
With a cold engine I also did a Compression check with 110 across the board. Could be better but again on a cold motor. The motor only has 200 miles on it.

[jwhelan65]

Hell, just go ahead and slap a turbo on there while you at Bill...

[rapidray]

Isnt it always summer in Calif?
I pulled my engine out today, took about 3 hours or so. Hopefully i can get the 1170 kit for it.
I maxed out my torque wrench (140#) taking off the front spocket, a little too tight eh? A source of my noise maybe.

Unless you LIKE to buy new torque wrenches, do NOT use a torque wrench to disassemble things! Ray.

[Kris V]

Unless you LIKE to buy new torque wrenches, do NOT use a torque wrench to disassemble things! Ray.

So true...

[gearhead13]

Unless you LIKE to buy new torque wrenches, do NOT use a torque wrench to disassemble things! Ray.

Ya, I have had this cheap torque wrench for 24 years or so, I KNOW its not accurate, but makes a good breaker bar I have a second 1/2" and another 3/8"
I dont know if you seen one of these antiques(pictured), but I call it my good torque wrench

[Octain]

Kudos to Bill!!

Ride the $hit out of it!