Testarossa's 1980 GS750L Project

[Testarossa]

It was suggested that I start a project thread about my GS750L. So, no time like the present. As some of you may remember from my intro thread, this is the bike that I purchased from a neighbor for the princely sum of $300. So after pushing the bike half a block down the street to my house, it's time to get my hands dirty.

My first test was to check out the electrics. I had to jump this bike to another battery. The one in the GS is stone dead. Happily, all the lights, horn, indicators, and ignition are working properly.

Next on the list was to see if the the plugs fire and if the bike seems to have compression. I pulled the plugs and then re-attached to the leads. Then I laid them on the head and tried to start the bike. All plugs are making a fat blue spark. Apparently, the previous owner has installed a Dyna S and Accel coils and wires. Obviously, I can see the wires and coils, but cannot verify the presence of the Dyna. I have not yet removed the ignition cover.

As for a compression test, I have opted not to find out how bad it really is yet. I do own a compression tester, but I don't want to find out at the moment that I'm making only 100 lbs on each cylinder. (The bike does have 55,000 miles.) So I just simply plug the hole with a finger and hit the starter. Not scientific, but I can verify that the bike does make plenty of compression to start.

Now on to trying to start the bike. I can verify that the previous owner has Kreemed the tank, but left fuel in there while parked. This fuel smells rancid, so I removed the tank, and replaced it with a lawnmower tank that I use for carb syncing. Of course, the o-rings on all of the fuel crossover pipes are dry and broken. Major fuel leak. Soooo, I separated the carbs and replaced the o-rings. Carbs back on and I try to start the bike to no avail. I decided to pull a drain screw, and the float bowls are dry.

Well, I removed the carbs and discovered that the needle and seats are totally stuck. I tried to quickly clean everything out without doing my usual extended soak in the parts cleaner. Unfortunately, I was un-successful at removing the seats. The varnish is rather tenacious in these carbs. I was hoping that the basic cleaning that I did would be clean enough to start, so back to the bike.

It tries to start, but acts as if it's not getting enough fuel yet. I was able to make it run on starter fluid, but as soon as the starter fluid runs out, it dies.

continued on next post....

[Testarossa]

Now, I also have a set of BS 34 carbs from another project, and decided to pull them apart and see how the seats are supposed to come out. I re-read the carburetor rebuild info in my Mega Welcome, and tore the 34's apart completely. I must say that that document is an in-valuable resource. Just being able to verify how to dis-assemble something when you are unsure helps a ton.

When I am able to find time, I'll pull the 32's off the GS and clean em out properly. Somewhere along the line, a previous owner has installed different sized pilot jets. It has a combination of 40 and 42.5 jets. Could anyone verify what all the factory jet sizes would be? Currently, I have 180 air jets, 40 and 42.5 pilots, and 117.5 main jets. The bike has a UNI foam air filter and the PO says that he drilled out the baffles. I guess that these mods may require slightly richer jets. I would like to start from stock and at least get it running on gasoline, and then adjust jet sizes from there.

Also, one of the pilot jets in the BS 34 set is well stuck. Someone was fooling around with these carbs before I got hold of them. I found one main jet in the float bowl, and the particular pilot jet has the screwdriver slot rounded off. Anyone have a suggestion for removing this jet without doing damage to the carb? I suppose I could drag the carb to work and drill it out (I'm a machinist.) However, there is a risk of ruining the carb body if I go that route. Anyone tried to heat em up a bit before removal? This rack has been dry from gas for at least a year, so I shouldn't have to worry about burning.

[azr]

Sounds like a good project so far. If you're looking for any carbs specs, they are all in the first post on the "carb/fuel/exhaust" section

http://www.thegsresources.com/_forum/showthread.php?t=73723

don't have much to offer with the stuck screws other than soak the heck out of them. I sure wouldn't try drilling them but you're the specialist in that department.

[Testarossa]

Awesome, thanks for the link. I'm working on shedding my newbieness. As for drilling out the jet, that's last resort. I would put the carburetor on one of our Bridgeport Mills and indicate the hole to find centerline. Then carefully drill it out, but even that makes me nervous. I'd sure like to get it out by conventional means.

[Testarossa]

Well, I made a small amount of progress this evening. I dis-assembled the carbs again, and allowed them to soak in the parts washer for 24 hrs. I was finally able to remove the needle and seats this time. Now with a proper cleaning the bike actually starts and runs on gasoline. Next step, I'll get a new battery and the stuff to change the oil. Bear with me as, this will take a little while. I'm really pushing to finish up my KZ1000 project. I'd already be done if I could paint worth a damn.

[Hoosier Daddy]

Any progress is good progress!

[Testarossa]

I just got done ordering some superbike bars, oil change stuff, valve cover gasket, and two pilot jets from Z1 Enterprises. Love Z1E! They always have what I need for my addiction.

So the plan is to change the oil, check valve clearances, adjust and sync the carbs, and get all the same jet sizes in all carbs. Love previous owners, they always do stuff to keep you on your toes. This one had 2 different sized pilot jets.

This should be fun. I'm so happy to not have to start with a total basketcase.

[Testarossa]

I hit a little snag on my other bike project yesterday, so I decided to start doing some maintenance on the GS today. First I wanted to lube and adjust the chain.


Of course, I discovered the reason why the bike has become difficult to push around. The rear brake caliper was stuck. I decided to see if I could get the piston moving again. I pulled the caliper apart to have a look.


Here's what I found:




This seems typical of any bike I have worked one that has sat for a while. There is a white powdery residue on the outside of the seal, and a resinous buildup around and behind the seal.


Once the caliper was cleaned and re-assembled, I bled the brakes and all is well. Got the chain lubed, and adjusted.

Then I decided to check out the front brakes. Of course those calipers were stuck as well. After I cleaned them up and bled the front, I discovered a leak around the base of the front reservoir. I'll have to replace that o-ring, and see if that seals the leak.

[Testarossa]

After playing with carburetor adjustments, it was idling well enough to go for a spin around the block. When I got back, I decided to shoot a quick video. Lets see if I can make this work.

http://www.youtube.com/watch?v=i5Zlp7eEmfU&list=UL6ALzAkfqLnU&playnext=1

OK that didn't work like I thought it would. Oh well, just click the link for my video.

[Hoosier Daddy]

Congrats!!!
Bet your neighbor is thrilled.

[Testarossa]

Congrats!!!
Bet your neighbor is thrilled.

Hahahahah! I must have rode past his house 10 times, and he never came out an looked. I know he was happy since I put some much needed cash in his hand before Christmas. We have a deal going. When I get the GS street legal I'm going to let him have one last ride, and he'll let me go for a spin on his Vulcan 2000. Potato-potato-potato.

I love it when I get one to the point that I can go for a spin. That's pure joy for me. Now I have to wait for parts.

Looks like this one might get painted soon. I had to dump out 1.5 gal of rancid gas from the tank. I tried the petcock first. No joy. It was plugged full of varnish. So I decided to dump it out through the filler neck. That wrecked his Rustoleum paint job. I'm needing to shoot a few more coats of clear on my KZ, so I may just shoot the GS at the same time.

[gearhead13]

I dont know if you got the pilots out yet, but I was able to remove buggered pilots by drilling a little, and using a small easy out. People try to use mal-fitting screwdrivers on these and just mess them up, not that they are so tight.
My 750 had 60k km on it, had 140 psi on all four when I got it. There was a TON of dirt/silt in the oil pan, might want to think about dropping it and cleaning, all that gunk goes through the oil pump unfiltered

[Testarossa]

Thanks gearhead13, that stuck jet was in another set of carbs. I probably wasn't too clear on that. Anyway, all my jets are nice and clean now. I learned about the jet screwdriver before on my boat. Since then I ground an old screwdriver that fits these jets tightly now. I have also used a left hand twist drill to remove broken, stuck screws before, but I'm not sure if I have one small enough. I'll cross that bridge later.

Is it possible to get the oil pan out while the motor is in the frame?

That black clutch dust really builds up in the bottom of these bike motors. One of the pleasures of running a wet clutch.

[gearhead13]

Is it possible to get the oil pan out while the motor is in the frame?

That black clutch dust really builds up in the bottom of these bike motors. One of the pleasures of running a wet clutch.

Should just have to pull the exhaust, and drop the pan

[Testarossa]

Sounds easy enough. Thanks again.